Main Wiring Loom Grommet
p/n: 20-1811-20
This Main Wiring Loom Grommet is used to run the main wiring loom to the firewall without being damaged by sheet metal. Designed from original part so it fits correctly.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Peel-N-Stick Trunk Weatherstrip
p/n: 20-1389-WT
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Radiator mounting pad
p/n: 20-1873-48
Pads, radiator support to frame. One upper & one lower. Two (2) required per car.
Rear Bumper Stone Deflector Seal
p/n: 20-1868-47
This Rear Bumper Stone Deflector Seal install between the body and rear bumper. This seal is an exact reproduction of the original bumper to body seal. The seal comes complete with installation fasteners.
Rear Spring Pad
p/n: 20-1275-32
This Rear Spring Pad is used as a spring insert silencer. The leaf spring insulator installs between the leaves.
Rear Window Gasket
p/n: 20-1776-81
This Rear Window Gasket around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Splash Apron
p/n: 20-1867-45
This four (4) piece Splash Apron pair is designed from the original part for superior fitment and seal. Installs on the fender splash apron.
Spring Clamp Liner Set
p/n: 20-1272-32
Six (6) piece Spring Clamp Liner Set. The front spring takes eight pieces for both sides and the rear spring takes four pieces for both sides.
Spring Shackle Bushing Set
p/n: 20-1834-32
This Spring Shackle Bushing Set is for the rear of the rear leaf spring on car models and the front of the front leaf spring on truck models. Two (2) sets needed per vehicle.
Spring Shackle Bushing Set
p/n: 20-1836-32
This Spring Shackle Bushing Set is for the front of the rear leaf spring. One (1) set completes one spring.
Spring Shackle or Shock Absorber Link Bushing
p/n: 20-1274-32
This Bushing is manufactured to OEM specifications to install for an authentic fit, finish and function. Used for front or rear leaf spring on Ford models. Used as a rubber, shock absorber link bushing on Chrysler models.
Stabilizer Bar Bushing Set
p/n: 20-1717-33
This four (4) piece Stabilizer Bar Bushing set is designed from the original part for superior fitment and function. These are the stabilizer bar to frame mounting bushings.
Stabilizer Bar Bushing Set
p/n: 20-1841-33
This twenty-six (26) piece Stabilizer Bar Bushing Set for the front is used to allow the rod to flex and rotate, but stays in place where it is attached to the vehicle frame.
Standard bumper
p/n: 20-1852-41
Bumper, fuel tank filler lid. Gray rubber.Ford Cars 1960-63 Bumper, license plate rubber. Used on rear bumper. 2 required per car.
Standard Bumper
p/n: 20-0001-88
This Standard Bumper pair is designed from the original part for superior fitment and function. This rubber bumper fits ashtray or glovebox doors.
Steering Column Floorplate
p/n: 20-1782-88
Seal, steering column to floor. Installs under floor mat.
Steering Column Floorplate
p/n: 20-1694-88
Seal, steering column tube. Installs on top of floor mat.
Taillight Mounting Pad
p/n: 20-1793-15
Kit, taillight mounting pad. Fin and Oval type. Six (6) piece set.
Transmission Mount
p/n: 20-1269-11
This Transmission Mount is designed from the original part for a correct fitment. Mounts at the rear of manual and automatic transmissions.
Trunk Weatherstrip
p/n: 20-1389-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Vent Window Division Post Weatherstrips
p/n: 20-1891-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Ventilator Air Inlet Duct Door Gaskets
p/n: 20-1827-31
This Ventilator Air Inlet Duct Door Gasket pair is designed from the original part for superior fitment and seal. These gaskets seal between the ventilator air inlet duct door to the duct inside.
Window Felt Beltline Weatherstrip - Left Quarter Window
p/n: 20-1901-60
This is a Standard material style Left Side Quarter Window only Window Felt Beltline Weatherstrip pair (also known as beltline weatherstrip). These anti-rattlers come ready to install with finished ends and body curvature bends for a factory like appearance.
Window Felt Beltline Weatherstrip - Right Quarter Window
p/n: 20-1900-60
This is a Standard material style Right Side Quarter Window only Window Felt Beltline Weatherstrip pair (also known as beltline weatherstrip). These anti-rattlers come ready to install with finished ends and body curvature bends for a factory like appearance.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Window Felt Beltline Weatherstrips - 3ft Pair
p/n: 30-0244-57
This side window Window Felt Beltline Weatherstrip pair can be used as inner and/or outer. The weatherstrip is flexible, pile lined, rubber covered, with black bead. Available in 3ft pairs.
Window Pinchweld Seal
p/n: 20-1882-52
Seal, garnish molding to dash rubber. Eighty four (84) inches long. Replaces factory #B7A-7003127-E.
Window Pinchweld Seal
p/n: 20-1881-52
Seal, garnish molding to dash rubber. Forty six (46) inches long. Models WITH A/C. Replaces factory #B7A-7003127-B.
Window Sash Channel
p/n: 20-1909-62
This Window Sash Channel is designed from the original part for superior fitment and seal. Thirty-four and three-fourths (34-3/4") inch long EPDM rubber extrusion that goes between glass and metal sash lift channel. One (1) roll required per window.
Windshield Gasket
p/n: 20-1874-50
This Windshield Gasket mounts around the full perimeter of the front glass. The weatherstrip has vulcanized, or bonded, ends which means no cutting or splicing is required. It also has the slot to accommodate the outer edge's decorative molding.
Wiring grommet
p/n: 20-1801-17
Grommet, license plate light wire. Installs where wire comes in rear bottom of trunk.