Radiator Stone Deflector Seal
p/n: 20-2954-28
Seal, front stone deflector to radiator. Nineteen and three fourths (19-3/4) inches long.
Splash Apron
p/n: 20-1320-45
This Splash Apron pair is designed to original specifications for superior fitment and proper seal. For front fender apron to frame front splash shield. Installation staples included.
Hood to Fender Bumper Set
p/n: 20-1312-42
This four (4) piece Hood to Fender Bumper Set is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure.
Taillight Lens Gaskets
p/n: 20-1230-15
A four (4) piece Taillight Lens Gasket set designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lens and taillight housing bezel.
Ventilator Air Valve Gaskets
p/n: 20-2966-31
This Ventilator Air Valve Gasket pair is designed from the original part for superior fitment and seal.
Hood bumper
p/n: 70-2871-42
Bumper, hood, front adjustable. Bumper threads into radiator support on left and right side. Two (2) required per car.
Overdrive Cable Grommet
p/n: 20-1812-20
This Overdrive Cable Grommet is used to help protect the overdrive pull cable when passing through the sheet metal of the firewall.
Trunk Decklid Adjustable Bumper
p/n: 70-2708-87
This Trunk Decklid Bumper is a quality reproduction of the original factory part. This adjustable rubber bumper attaches to the vehicle body to support / cushion the trunk lid closure. Screws into trunk. Two (2) required per car.
Headlight Bucket To Fender Gasket
p/n: 20-1542-14
This Headlight Bucket To Fender Gasket is designed from the original part for superior fitment and seal. These gasket fits the headlight bucket and front fender.
Back-up Light Gaskets
p/n: 20-1249-17
This Back-up Light Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the Back-up Light Housing to the vehicle body.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Hood bumper
p/n: 70-2876-42
Bumper, hood adjustable, rear. Slip-over rubber cover for threaded stud that mounts on both sides of cowl.
Rear Spring Pad
p/n: 20-1275-32
This Rear Spring Pad is used as a spring insert silencer. The leaf spring insulator installs between the leaves.
Trunk Bumper
p/n: 70-2741-87
Bumpers, adjustable trunk. Screws into trunk. Two (2) required per car.
Hood Bumper
p/n: 70-2735-42
This adjustable Hood Bumper mounts at the front of the vehicle over the radiator. 1.0 x 44mm thread with 23mm hex head.
Windshield Wiper Pivot Gaskets
p/n: 20-1326-53
This Windshield Wiper Pivot Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the wiper pivot bezel to the cowl structure.
1/16" Sash Channel Filler - Cork
p/n: 70-1115-57
This 1/16" Sash Channel Filler offers the best quality cork product for your classic vehicle project. Manufactured to OEM specifications to install for an authentic fit and finish. Available by the foot.
Body Hole Plug
p/n: 20-1041-21
Plug, cowl and floor pan. This body plug covers a sheet metal hole that is one and one seven eighths (1-7/8) inch in diameter.
Accelerator Pedal Rod Seal
p/n: 20-1448-41
This Accelerator Pedal Rod Seal is used to run the pedal linkage to the firewall. Designed from original part so it fits correctly.
Clutch or Brake Pedal Bumper
p/n: 20-1051-24
This Clutch or Brake Pedal Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a clutch or brake pedal arm stop cushion.
Standard Bumper
p/n: 20-0001-88
This Standard Bumper pair is designed from the original part for superior fitment and function. This rubber bumper fits ashtray or glovebox doors.
Front fender center pad
p/n: 20-1865-45
Pads, back center of front fender. Mounts where fender bolts to cowl.
Door Bumper
p/n: 20-0067-71
This Door Bumper is designed from the original part for an authentic fit, finish and function. Installs on back edge of door. Usually two (2) to eight (8) per vehicle.
Door Bumper, Upper / Lower
p/n: 20-2825-71
This Door Bumper is a quality reproduction of the original factory part. Upper / Lower push-in type. Four (4) required per car.
Glovebox Arm Bumper Stop
p/n: 20-1399-88
Stop, glovebox arm.Ford Truck 1957-64 Stop, glovebox arm. Requires 2 each. Ford Cars 1955-68 Bumper, glovebox door check arm stop.
Hood bumper
p/n: 20-1309-42
Bumper, hood pull cam. Two (2) required per car.Ford Cars 1957-60 Bumper, hood pull cam. 2 required per car. Ford Cars 1958-59 Bumper, trunk lid.
Spring Shackle or Shock Absorber Link Bushing
p/n: 20-1274-32
This Bushing is manufactured to OEM specifications to install for an authentic fit, finish and function. Used for front or rear leaf spring on Ford models. Used as a rubber, shock absorber link bushing on Chrysler models.
1-1/4" Body Hole Plug
p/n: 20-1039-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one fourth (1-1/4") inches in diameter.
Body Hole Plug
p/n: 20-1040-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one half (1-1/2") inch in diameter.