Front Door Vent Window Weatherstrips
p/n: 20-1110-55
These Front Door Vent Window Weatherstrips are designed from the original parts for superior fitment and seal. Molded as left and right and contain metal cores with attaching tabs that run vertically on the division post.
Sound Deadener Underlayment Set
p/n: 70-4602-88
This five (5) piece die-cut Sound Deadener Underlayment Set lays under the carpet. This sound deadener will decrease road noise and decrease heat inside the interior compartment. Pre-cut and ready to be installed into your vehicle to improve driving comfort.
Voltage Regulator Cover Shield
p/n: 70-4531-17
This Voltage Regulator Cover Shield is designed from the original part for superior fitment and function. This cover shield is located over and above the voltage regulator.
Steering Column At Floor Seal
p/n: 20-1072-36
This Steering Column At Floor Seal is designed from the original part for superior fitment and sealing. This part fits around the steering column to seal the column at the body floor pan.
Trunk Weatherstrip
p/n: 20-0302-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The decklid weatherstrip mounts around the full perimeter of the trunk directly to the body.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1089-42
This Firewall To Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. An exact reproduction using dense and sponge rubber extrusion with fasteners imbedded in place as original.
Accelerator Pedal Pad
p/n: 20-1075-40
This Accelerator Pedal Pad is made of top-quality EPDM rubber with a high level of fit and finish. Designed to be a direct fit reproduction.
Rear Leaf Spring Shackle Assembly
p/n: 20-1066-32
This reproduction Rear Leaf Spring Shackle Assembly is complete with shackle bar plates, rubber bushings and lock nuts. For fitting the suspension leaf spring at its rear spring eye to the vehicle body. Two (2) assemblies required per car.
Brake Pedal Pad
p/n: 20-1044-22
Pad, brake pedal. Models with automatic transmission and manual brakes.
Rear Leaf Spring Insulator
p/n: 20-2733-32
This Rear Leaf Spring Insulator is an exact replacement of the rear spring center mount rubber insulator block that mounts below the leaf spring. Four (4) required per vehicle. Fits 2-1/2" leaf spring.
Clutch Pedal Rod Boot
p/n: 20-1049-23
This Clutch Pedal Rod Boot is designed from the original part for superior fitment and seal. Accordion style boot seals the clutch rod to the floor.
Adjustable Hood Bumper
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Brake Pedal Pad
p/n: 20-1043-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pad for models with manual transmission and manual drum (not disc) brakes.
Accelerator Pedal Rod Seal
p/n: 20-2745-41
This Accelerator Pedal Rod Seal is used when running the accelerator rod through the firewall. The seal helps to block out air and wind noise from entering into the cabin.
Door Bumper
p/n: 20-0067-71
This Door Bumper is designed from the original part for an authentic fit, finish and function. Installs on back edge of door. Usually two (2) to eight (8) per vehicle.
1-1/4" Body Hole Plug
p/n: 20-1039-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is one and one fourth (1-1/4") inches in diameter.
3/4" Body Hole Plug
p/n: 20-1038-21
This Body Hole Plug is designed from the original part for superior fitment, finish and function. This plug is made from high quality EPDM dense rubber to provide excellent durability. This body plug covers a sheet metal hole that is three-fourths (3/4") inches in diameter.
Sun Visor Tips
p/n: 20-2882-88
These Sun Visor Tips are reproductions manufactured to OEM specifications to install for an authentic fit, finish and function. Sold as a pair.