Front Door weatherstrip
p/n: 90-0145-72
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Rear Window Gasket
p/n: 70-0533-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has the divider bars molded directly into it. It has properly molded corners to precisely conform to the glass and has the slot to accommodate the outer edge's decorative molding.
Front Door weatherstrip
p/n: 50-0558-72
Door edge weatherstrip. This part is the primary door to body weatherstrip.
Windshield Gasket
p/n: 70-0526-50
This Windshield Gasket mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. This seal has molded sections for the wiper transmissions and the slot to accommodate the outer edge molding.
Front Door Vent Window Set
p/n: 90-0395-90
This Front Door Vent Window Set is a six (6) piece set that contains the main vent window seals, base extensions, and division post seals. All of the pieces were designed from original parts for a precise, factory fit.
Front Door Vent Window Weatherstrips
p/n: 38-0051-55
This Front Door Vent Window Weatherstrips contain the main seals for the vent windows and the base extension pieces for the frame. They are designed and molded from original parts for superior fitment and seal.
Hardtop Roof Rail Weatherstrip
p/n: 70-0570-68
Hardtop roof rail weatherstrip (1950-2nd type). Goes over the front doors only. This part fits on the roof of the vehicle and seals the side window when the window is fully raised.
Door weatherstrip
p/n: 70-0948-73
Weatherstrip, front door bottom. High quality weatherstrip with molded right and left hand ends.
Door Weatherstrip
p/n: 70-0550-73
Weatherstrip, door bottom (1951-2nd type). Molded left and right, overall length forty (40) inches.
Engine Mount Service – Revulcanization Only
p/n: 25-0072-11
This Revulcanization Service Only is designed to restore your Right and Left Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Trunk Weatherstrip
p/n: 70-1039-84
This Trunk Weatherstrip set is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Trunk Weatherstrip
p/n: 70-0870-84
This Trunk Weatherstrip is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the lid.
Trunk Weatherstrip Set
p/n: 70-0871-84
This Trunk Weatherstrip Set is designed from original parts for superior fitment and seal. The set contains the strips and corners that mount to the body and the strip that mounts to the decklid.
Engine Mount Service – Revulcanization Only
p/n: 25-0077-11
This Revulcanization Service Only is designed to restore your Front Lower Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Engine Mount Service – Revulcanization Only
p/n: 25-0062-11
This Revulcanization Service Only is designed to restore your Front Upper Engine Mount at Crossmember to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Door Weatherstrip
p/n: 70-0668-73
Weatherstrip, body hinge pillar to door, bellows type of seal. One thirty seconds (1/32) inch thick. Die cut to exact outline.Length: 29.50 inches.
Trunk Weatherstrip Corners
p/n: 60-0511-85
These trunk weatherstrip corners are designed from the original part for superior fitment and seal. The seals mount to the front corners of the trunk directly to the body.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Hood to Cowl Weatherstrip
p/n: 70-0940-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Front Spring Rubber Bumpers
p/n: 70-0329-32
This Front Spring Rubber Bumper Pair fits to the upper control arms on frame. Manufactured to OEM specifications to install for an authentic fit, finish and function.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Vent division bar weatherstrip
p/n: 70-0821-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Gearshift Boot
p/n: 70-2126-24
Boot, transmission gear hand shift lever. Molded in pliable black rubber which may be painted if needed for restoration.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Front Stabilizer Bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber.
Door Conduit
p/n: 70-0828-21
Conduit, hydraulic line & power window wire. Front doors only. 2 pieces cut nine and one half (9-1/2) inches.Length: 9.50 inches. Height: 1.50 inches.
Fender Skirt Edge Weatherstrip
p/n: 60-0109-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish, and seal. This weatherstrips fits between the rear wheel fender skirt and the rear fender quarter panel.
Door Weatherstrip
p/n: 50-0219-73
This Door Weatherstrip is made of a high-quality sponge extrusion to original configuration. This weatherstrip is for the front door opening, lower front body hinge pillar.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Body Mounting Pad
p/n: 27-0092-48
Insulator, body mounting pad. Metal core & locating collar covered with rubber.
Body Mounting Pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Side Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Solenoid Plunger Boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Wiring Grommet
p/n: 70-0355-14
This Wiring Grommet is used to run electric wire into light body under fenders, for headlights, taillights, some parking lights and auxiliary (fog) lights. Fully molded from top-quality EPDM dense rubber to provide excellent durability.
Window Stop Stem Bumper
p/n: 33-0622-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and function. Designed as a window stop cushion for front and rear door, rear side and quarter windows as needed.
