Front Stabilizer Bushing
p/n: 30-0363-33
Bearings or bushings, front stabilizer rod. One (1) pair used per vehicle. Fully molded rubber.
Front Stabilizer Bushing
p/n: 30-0123-33
Bushings, front stabilizer mounting bracket. Fully molded rubber.
Front suspension bumper
p/n: 30-0229-32
Bumper assembly, front suspension rebound (upper arm). Straight style with stud.
Front Suspension Bumper
p/n: 30-0489-32
Bumper, front suspension (inside of coil spring). Made with three eighths (3/8) inch stud as original.
Front Suspension Bumper
p/n: 30-0228-32
Bumper assembly, front suspension inside coil spring, with five sixteenths (5/16) inch threaded studs as found originally.
Front Suspension Bumper
p/n: 70-1294-32
Bumper, front load rebound, upper.Width: 1.625 inches. Height: 2.75 inches.
Front Suspension Bumper
p/n: 70-1295-32
Bumper assembly, front load compression, lower.Width: 2.125 inches. Height: 2.75 inches.
Front Suspension Bumper
p/n: 30-0490-32
Bumper, front suspension (inside of coil spring). Made with three five sixteenths (5/16) inch studs as original.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Fuel Filler Neck Grommet
p/n: 30-0158-41
This Fuel Filler Neck To Body Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Fuel Line Grommet
p/n: 30-0320-41
Grommet, fuel line through engine pan. Two and one fourth (2-1/4) inch diameter.
Fuel Line Grommet
p/n: 30-0045-41
Grommet, fuel gauge and gas line through rear frame cross member. For five eighths (5/8) inch by two and three eighths (2-3/8) inch slot.Length: 2.
Fuel Neck Grommet
p/n: 30-0101-41
Grommet, fuel filler neck. For inside of body, on floor of wheel carrier.
Fuel Neck Grommet
p/n: 30-0099-41
Grommet, fuel filler neck. Three and one half (3-7/16) inch inside diameter for four (4) inch hole in apron.
Fuel Neck Grommet
p/n: 30-0241-41
Grommet, gas tank inlet to wheel housing. Also used as grommet, gas tank inlet tube to wheel compartment bottom.
Fuel Neck Grommet
p/n: 30-0232-41
Grommet, fuel filler neck. 2-1/2" inside diameter. Fits 3-3/8" hole in sheet metal. Overall width 4-1/8".
Fuel Neck Grommet
p/n: 30-0157-41
Seal, fuel filler neck through rumble seat floor pan. Highest quality workmanship, rubber with brass core as original.
Fuel Tank Support Pad
p/n: 30-0482-41
This Fuel Tank Support Pad is made of a high quality EPDM dense rubber. This cushion is used to help reduce noise. Available by the foot.
Gearshift Boot
p/n: 30-0178-24
Boot, gearshift cover. For cane shifts only. Length: 4.0 inches. Width: 3.0 inches. Height: 5.125 inches.
Gearshift Boot
p/n: 30-0129-24
Boot for column gearshift, short type. Black rubber. For brown see our #30-0129-89. All series with column shift.Height: 1.4375 inches.
Gearshift Boot
p/n: 30-0412-24
Grommet, shifter shaft to shroud. One (1) per car.Length: 4.125 inches. Width: 2.3125 inches.
Gearshift Seal
p/n: 30-0165-24
Seal, gearshift to floorboard.Length: 5.625 inches. Width: 4.875 inches.
Gravel Shield
p/n: 30-0007-44
Gravel deflector, underside of running board at rear. Length: 7.125 inches.
Gravel shield bumper
p/n: 70-2825-44
Anti-rattler, front stone shield. Insulates the front stone shield from the front bumper. Six (6) piece set.
Gravel Shield Bumper
p/n: 30-0384-44
Cushion, rear gravel to bumper. Six (6) feet long. One (1) strip required per car.Length: 72.00 inches. Width: .25 inches. Height: .6875 inches.
Hardtop Weatherstrip
p/n: 70-2012-68
Weatherstrip, hardtop roof rail, auxiliary. Installed in side window flipper seal. This is a factory service department fix designed to reduce wind noise on 56th series hardtops that also can be used on 55th series models.
Harmonic Balancer - Revulcanization Service
p/n: 30-0520-12
This front Harmonic Balancer - Revulcanization Service is designed to restore your engine's vibration damper to a like new original condition. Service only requires your metal core. Please call or email for more service details and ordering.
Headlight Lens Gasket
p/n: 30-0176-14
Gaskets, headlight lens and reflector mounting. A three sixteenths (3/16) inch cross section rubber ring of proper diameter.
Headlight Mounting Pad
p/n: 30-0142-14
Gaskets, headlight body mounting to fender. Cut to exact size as original.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Headlight Mounting Pad
p/n: 30-0291-14
Pads, headlight support bar to fender. Molded right and left.Length: 3.75 inches. Width: 3.75 inches.
Headlight Mounting Pad
p/n: 30-0265-14
Mounting pad, headlight bracket to fender. Molded right and left with proper beading and shape as original.Length: 9.375 inches.
Headlight Mounting Pad
p/n: 30-0134-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. Made with a metal core. This pad acts as the headlight adjusting collar.
Headlight Mounting Pad
p/n: 30-0354-14
Gasket, headlight front assembly to fender. Between headlight bucket and the fender receiver hole. One (1) pair per car, sold only in pairs.
Headlight Mounting Pad
p/n: 30-0145-14
Pads, headlight bracket to fender mounting. Proper edge form.Length: 4.375 inches.
Headlight Mounting Pad
p/n: 30-0133-14
Pads, headlight bracket mounting to fender. Molded left and right. Proper construction with beading as original. Sold in complete pairs only.Length: 9.
Headlight Mounting Pad Set
p/n: 30-0236-14
Pad set, headlight mounting. Six (6) piece replacement set. Sold in complete sets only.
Headlight Mounting Pad Set
p/n: 30-0161-14
Pad and Grommet Set, headlight support bar to radiator shell. Four (4) piece set, sold in complete sets only.
Headlight stanchion pad
p/n: 30-0240-14
Cushion (rubber washer), front light to radiator shell. One (1) pair required per car.
Headliner Retainer Grommet
p/n: 70-1713-88
Grommet, headliner bow end. Twelve (12) required per car.Length: 1.4375 inches.
Heater core tube grommet
p/n: 30-0421-31
Grommet, heater inlet and outlet hose. Soft pliable rubber.
Heel plate
p/n: 70-3608-88
Heel plate to protect driver's side floor carpet. Identical to original. Only for models with carpet.
Hinge Post Weatherstrip
p/n: 30-0381-73
Weatherstrip, right and left hinge side on front door, convertible styles only.
Hood Bumper
p/n: 30-0150-42
Bumpers, hood rest, reversible.Length: 2.1875 inches. Width: 1.5625 inches.
Hood Bumper
p/n: 30-0080-42
Bumper, inner hood rest. Good copy and material. One (1) pair required per car.Length: 1.50 inches. Width: .875 inches.
Hood Bumper
p/n: 30-0151-42
Bumpers, hood catch. Right and left.Length: 2.50 inches. Width: 1.4375 inches.
Hood Corner Pad
p/n: 30-0088-42
Pad, hood front corner. Metal core, retained by four (4) tabs.Length: 3.25 inches. Width: 1.25 inches.
Hood Corner Pad
p/n: 30-0010-42
Pads, hood rear corners. High quality rubber with metal core as original.Length: 3.4375 inches. Width: 1.875 inches.
Hood Corner Pad
p/n: 30-0130-42
Pads, hood front corners. Large self prong type with metal core molded left and right.Length: 3.375 inches.
Hood Corner Pad
p/n: 30-0183-42
Pads, hood corners. Right and left replacement. Brass core, integral holding tabs.Length: 3.125 inches.
Hood Corner Pad
p/n: 30-0037-42
Pads, hood front corner. Metal core, retained by single rivet.Length: 1.75 inches. Width: 1.375 inches.
Hood Corner Pad
p/n: 30-0225-42
Pads, front and rear hood corners, brass core, right angle.Length: 2.625 inches. Width: 2.625 inches.
Hood Corner Pad
p/n: 30-0059-42
Pad, hood rear corner. Molded left and right with a metal core. Length: 2.50 inches. Width: 1.75 inches.
Hood Corner Pad
p/n: 30-0011-42
Pads, hood front corners, large type. Molded right and left with metal cores and double tab retainers.Length: 3.1875 inches. Width: 2.125 inches.
Hood Hinge Top Strap Pivot
p/n: 70-0045-42
A Hood Hinge Top Strap Pivot manufactured to OEM specifications to install for an authentic fit and finish. Cold rolled steel as original.
Hood Inner Center Rest Pad
p/n: 30-0222-42
This Hood Inner Center Rest Pad pair is designed from the original part for an authentic fit, finish, and appearance. Rubber only pads that fit original bracket.
Hood Rest Pad
p/n: 30-0092-42
Hood Rest Pad. Molded rubber with a steel core. Six (6) required per car. Length: 1.75 inches Width: 1.625 inches.
Hood to Cowl Bumpers
p/n: 30-0223-42
Bumpers, hood to cowl. Brass core, one and one half (1-1/2) inch by four and one half (4-1/2) inch.Length: 4.50 inches. Width: 1.50 inches.
Hood to Cowl Weatherstrip
p/n: 30-0138-42
Guard strip, hood to cowl. Brass core with molded integral hood rest.Length: 14.875 inches.
Hood to Cowl Weatherstrip
p/n: 30-0233-42
Seal, hood to cowl. High quality closed cell sponge rubber construction as original.Width: .4375 inches. Height: .5625 inches.
Hood to Cowl Weatherstrip
p/n: 70-1296-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. Fully molded with carrot-bumper retainers.
Hood to Cowl Weatherstrip
p/n: 30-0049-42
Scuff pad, hood to cowl. Superior duplication of part with better rubber than original.Length: 8.25 inches.
Hood to Cowl Weatherstrip
p/n: 30-0527-42
Weatherstrip, hood to cowl. Overall thirty seven (37) inches long.
Hood to Fender Bumper
p/n: 30-0304-42
This Hood to Fender Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Six (6) required per car.
Horn Cover Bumper
p/n: 30-0283-21
Bumpers, horn cover. Rubber with brass core construction like original.Length: 4.0 inches. Width: .625 inches.
Hydraulic Pump Mounting Pad
p/n: 70-1610-67
Cushion mount, hydraulic pump.Width: .6875 inches. Height: 1.0 inches.
Ignition Cable Grommet
p/n: 70-1598-21
Grommet, ignition cable.Length: 2.125 inches. Width: 1.50 inches.
Instrument board retainer
p/n: 70-3609-20
Instrument board wind lace retainer. Both R & L sides. Anti-rattle instrument panel ends. 11 1/4" long. Replaces 310646 & 310647.
Insulator
p/n: 30-0404-48
Insulator, used on various places on vehicle. Uses 10 to 14 per car running board to frame bracket. Replaces factory #324851.
License Lens Gasket
p/n: 70-2121-17
Gasket, rear bumper license plate lens. Machine die-cut from 1/16" rubber.Length: 6.5625 inches. Width: 1.625 inches.
License Light Mounting Pad
p/n: 30-0122-17
Pad, rear license light mounting, with correct dimensions and beading.Length: 8.125 inches.
Lock Cylinder Gasket
p/n: 30-0022-71
Pads, door handle escutcheon.Width: 1.875 inches. Height: 1.375 inches.
Lock cylinder gasket
p/n: 30-0389-71
Gasket, door lock handle escutcheon, front and rear doors. Two (2) or four (4) required per car.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Overdrive Linkage Grommet
p/n: 70-2031-24
Grommet, overdrive control linkage. Spool type grommet used on manual transmission models with factory overdrive. Three fourths inch (3/4") outside diameter by three eighths inch (3/8") inside hole diameter by three eighths inch (3/8") height.
Parking Light Gasket
p/n: 70-2023-15
Gasket, parking light housing. Die cut from durable black sponge-cell rubber. One (1) pair needed per car.Length: 11.375 inches.
Parking Light Lens Gasket
p/n: 70-1521-16
Gasket, parking light lens.Length: 14.875 inches. Width: 2.0 inches.