Parking Light Mounting Pad
p/n: 30-0195-17
Gaskets, front parking light to fender.Length: 19.875 inches.
Parking Light Mounting Pad
p/n: 30-0447-17
Pad, parking light to fender. Requires two (2) per car.Length: 4.125 inches.
Parking Light Mounting Pad
p/n: 30-0282-17
Gaskets, parking light (fender light).Length: 2.75 inches. Width: 1.75 inches.
Parking Light Mounting Pad
p/n: 30-0416-17
Gasket, fender light. Faithful copy with correct shape and detail as originalLength: 2.75 inches.
Peel-N-Stick Door Edge Weatherstrip
p/n: 70-0390-WT
This Peel-N-Stick Door Edge Weatherstrip is designed for a specific set of vehicles but with its generic shape, has many uses outside of its original purpose. Available by the foot. Available by the foot.
Peel-N-Stick Door Weatherstrip
p/n: 70-0331-WT
This Peel-N-Stick Door Weatherstrip is made from high-quality EPDM sponge rubber. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-1691-WT
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The self-adhesive weatherstrip mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-1690-WT
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The self-adhesive weatherstrip mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Peel-N-Stick Trunk Weatherstrip
p/n: 30-0356-WT
This trunk weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Plug Wire Sleeve
p/n: 30-0204-21
Sleeve, plug wire tube to distributor cap. One (1) pair required per car.Height: .9375 inches.
Power brake carpet grommet
p/n: 70-3147-24
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Power brake pedal pad
p/n: 70-2411-22
Cover, power brake pedal, with "Easamatic power brake" logo. Fully molded with script just like original.
Power Steering Bushing
p/n: 70-1968-36
Bushing, power steering cylinder to frame. Two (2) required per car.Height: .625 inches.
Power window switch bezel pad
p/n: 70-2136-21
Mounting pad, power window die cast bezel. Used under single window switch, typically found on front passenger door and rear windows.
Power Window Switch Bezel Pad
p/n: 70-2137-21
Mounting pad, power window die cast bezel. Used under 4 way switch, typically found on drivers door.Width: 2.0 inches.
Prop shaft retainer bushing
p/n: 70-2268-27
Retainer, intermediate bearing. All models with two piece driveshafts.
Prop shaft support service
p/n: 30-0526-24
Support, drive shaft intermediate bearing retainer. Revulcanization service only.
Radiator Mounting Pad
p/n: 30-0395-31
Spacer or Pad, radiator anchorage stud, upper stud. One (1) pair required per car.Length: 2.5625 inches.
Radiator Mounting Pad
p/n: 30-0208-31
Pad, radiator lower splasher to grille. Fastens into place with rivets. One four (4) piece set required per car.Length: .875 inches. Width: .875 inches.
Radiator Mounting Pad
p/n: 30-0309-31
Grommet, several usages. Radiator core cradle tie rod to frame or rear stabilizer pad to link to where the leaf springs are bolted. Fully molded rubber. 2nd type with chamfered edge. Comes as a (4) piece set.
Radiator Mounting Pad
p/n: 30-0451-31
Spacer or Pad, lower radiator anchor stud. Used in conjunction with our #30-0395-31.Height: .3125 inches.
Radiator mounting pad
p/n: 30-0121-31
Grommet, radiator cradle to frame tie rod. 1st type, with locating boss. One four (4) piece set required per car. See also our #30-0309-31.
Radiator Mounting Pad
p/n: 30-0469-31
Pad (or Grommet), radiator to dash tie rod. Die cut from one fourth (1/4) inch rubber. Four (4) used per car.Height: .25 inches.
Radiator Mounting Pad
p/n: 30-0209-31
Shim, radiator core mounting stud spacer. Fully molded rubber. Use as required. Comes as a pair of two (2). Two and seven eighths inch (2 7/8") square by five eighths inch (5/8") inside hole diameter by three eighths inch (3/8") height.
Rear Bumper Grommet
p/n: 30-0006-29
Grommets, rear bumper.Length: 3.625 inches. Width: 3.3125 inches.
Rear Bumper Grommet
p/n: 30-0078-29
Grommets, rear bumper. Molded left and right as original with excellent detailing. Fully molded rubber with retaining flange.
Rear Bumper Grommet
p/n: 30-0047-29
Grommets, rear bumper. For models with luggage racks. Length: 4.125 inches. Width: 3.375 inches.
Rear Bumper Grommet
p/n: 30-0067-29
Grommets, rear bumper. Length: 4.3125 inches. Width: 2.6875 inches.
Rear Bumper Grommet
p/n: 30-0127-29
Grommets, rear bumper extension bar through rear fender for wrap around bumpers. Fully molded rubber w/ full detail as in original.
Rear Bumper Grommet
p/n: 30-0197-29
Grommets, rear bumper. Molded left and right. Fully molded rubber.
Rear Bumper Grommet
p/n: 30-0137-29
Grommets, rear bumper support bar to body. Fully molded rubber w/ retaining flange.
Rear Door hinge pillar seal
p/n: 30-0496-73
Weatherstrip, rear door hinge pillar. Attaches to body on hinge pillar. Molded without metal core.
Rear door vent weatherstrip
p/n: 30-0118-74
Rear door vent window rubber. Order our #30-0347-74 division post seal separately.
Rear Door Vent Window Weatherstrips
p/n: 30-0481-74
This Rear Door Vent Window Weatherstrip pair is designed from the original parts for superior fitment and seal.
Rear door weatherstrip
p/n: 90-0121-72
Weatherstrip, rear door kit. Includes sufficient weatherstrip for door perimeter, bottom and hinge pillar. Adhesive is not included in the kit.
Rear Door weatherstrip
p/n: 90-0147-72
Weatherstrip, rear door kit. Includes weatherstrip for door perimeter and hinge pillars.
Rear Engine Mount Service - Revulcanization Only
p/n: 30-0403-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Rear Engine Mount Service - Revulcanization Only
p/n: 30-0509-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Rear Engine Support Assembly - Revulcanization Only
p/n: 30-0328-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Rear quarter vent weatherstrip
p/n: 30-0187-77
Weatherstrip, rear quarter vent window. Full swing type.
Rear Quarter Vent Window Weatherstrips
p/n: 30-0333-77
This Rear Quarter Vent Window Weatherstrip pair is designed from the original parts for superior fitment and seal. A two (2) piece pair that fits both driver (Left) and passenger (Right) sides of the rear quarter panel vent / wing window assemblies.
Rear Quarter Vent Window Weatherstrips
p/n: 30-0249-77
This Rear Quarter Vent Window Weatherstrip pair is designed from the original part for superior fitment and seal. For full swing type rear vent windows.
Rear Quarter Vent Window Weatherstrips
p/n: 30-0016-77
This full swing type Rear Quarter Vent Window Weatherstrip pair is designed from the original part for superior fitment and seal.
Rear Shield to Bumper Seal
p/n: 30-0476-44
This Rear Shield to Bumper Seal is made of high quality EPDM dense rubber. The seal is designed from an original part so it fits correctly. Overall length is seven (7) feet.
Rear Spring Pad
p/n: 30-0452-32
Insulator, rear spring leaf clip. Seven and one half (7-1/2) inch long, customer may trim for shorter lengths. May use up to eight (8) per car.
Rear Spring Pad
p/n: 70-2080-32
Pad, rear spring insulator. Order four (4) per car.Length: 4.75 inches. Width: 2.875 inches.
Rear Spring Pad
p/n: 70-0245-32
Pad, rear spring insulator for two and one fourth (2-1/4) inch wide springs. (see our number 70-0191-32 for two (2) inch springs). Four (4) per vehicle.
Rear spring pad
p/n: 30-0370-32
Separator, spring leaf, rear. Use as required, up to twenty four (24) needed per car.
Rear Stabilizer Bushing
p/n: 70-1967-33
Bushing, rear stabilizer. Four (4) are required per car. Fully molded rubber. One and one half inch (1 1/2") outside diameter by five eighths inch (5/8") inside hole diameter by seven eighths inch (7/8") height.
Rear Window Gasket
p/n: 30-0392-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. Designed to be used with reveal molding (not included).
Rear Window Gasket
p/n: 30-0485-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 30-0522-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 30-0358-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. For vehicles with perimeter reveal molding.
Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Rear Window Gasket
p/n: 30-0141-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket
p/n: 30-0359-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 30-0513-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. Designed to be used with reveal molding.
Rear Window Gasket
p/n: 30-0488-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 30-0086-83
This Rear Window Gasket comes in a seven (7) foot strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Rear Window Gasket
p/n: 30-0479-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket Set
p/n: 70-1818-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The seal mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Rear Window Gasket Set
p/n: 30-0487-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The gasket has the divider bars molded directly into it and has molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket Set
p/n: 30-0529-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The seal mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket Set
p/n: 30-0505-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The seal mounts around the full perimeter of the back glass and has properly molded corners. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket Set
p/n: 30-0368-81
This Rear Window Gasket Set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket Set
p/n: 30-0465-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The gasket has the divider bars molded directly into it and has molded corners for a precise, factory fit. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket Set
p/n: 30-0511-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The seal mounts around the full perimeter of the back glass and the locking strip holds it tight for a precise, factory fit.
Rear Window Gasket Set
p/n: 70-1682-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The seal mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Rear Window Gasket Set
p/n: 30-0289-81
This Rear Window Gasket Set mounts around the two (2) separate back windows. They have vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket Set
p/n: 30-0463-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The seal mounts around the full perimeter of the back glass and has properly molded corners for a precise, factory fit.
Rear Window Gasket Set
p/n: 30-0506-81
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. The seal mounts around the full perimeter of the back glass and the locking strip holds it tight for a precise, factory fit.
Red Brake and Clutch Pedal Pad
p/n: 30-0114-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0114-22.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Rigid Run Channel
p/n: 30-0180-57
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Rigid Run Channels
p/n: 30-0023-57
This Rigid Run Channel pair for the division bar is un-beaded, steel core, plush lined, and cloth covered. Available as 28" pair.
Roof emblem mounting pad
p/n: 70-2575-88
Pad, roof emblem mounting gasket. Machine die cut sponge rubber to exact required shape.
Rumble Seat Lid Bumper Pad
p/n: 30-0275-44
Bumpers, rumble seat stop bracket. Self-retaining type as original.Length: 1.1875 inches. Width: .75 inches. Height: .375 inches.
Rumble Seat Step Mounting Pad
p/n: 30-0271-44
Gasket, rumble seat step center. Length: 5.875 inches.
Rumble Seat Step Mounting Pad
p/n: 30-0181-44
Pad, rumble seat step bracket to fender. Four and one fourth (4-1/4) inch long.Length: 4.375 inches.
Rumble Seat Step Mounting Pad
p/n: 30-0272-44
Gasket, rumble seat step. For left hand drive upper. Length: 5.0 inches.
Running Board Center Strip
p/n: 30-0034-49
Running board center strip. Fits original metal retainer. Authentic reproduction with correct detail.
Running Board Door Opening Step Pads
p/n: 30-0216-49
This Running Board Door Opening Step Pad pair is designed from the original part for superior fitment and seal. Provides a perfect copy of the original accessory.
Running Board Edge Seal
p/n: 30-0169-44
Liner, running board to body, (side apron to body seal). Set consists of two (2) pieces seven (7) foot long. One (1) inch width is after fold over.
Running Board Matting
p/n: 30-0218-49
Running board matting for Model 115C only. Made from the molded running board matting for the 120's (our #30-0214-49).
Running Board Matting
p/n: 30-0428-49
This reproduction Running Board Matting pair is designed from the original part for superior fitment, finish and function. Fully molded with crowned blocks. Top quality rubber, flawless detail. No splicing or butting required.
Running Board Matting
p/n: 30-0214-49
Running board matting. Fully molded right and left hand. Top quality rubber, flawless detail. Includes rubber cross molding for in front of rear fender.