Window Felt Beltline Weatherstrips
p/n: 70-0555-58
These Window Felt Beltline Weatherstrips are sold as a three (3) foot pair. The beltline is used for side windows inner and/or outer, front and/or rear doors. Available in a 3ft pair.
Clutch Control Boot
p/n: 30-0273-24
Boot, clutch control unit governor.1940-42: Cars with Overdrive 1941-42: Cars with Electromatic
Engine Snubber Pad Set
p/n: 30-0311-11
This four (4) piece Engine Snubber Pad Set is designed from original for correct fit and function. Sold only in complete sets. One four (4) piece set required per car.
Firewall Grommet
p/n: 30-0070-21
This Firewall Grommet is used to run instrument board cables through the firewall. The oval type with masked hole for six (6) wires or cables is the necessary replacement for correct restoration.
Cowl Vent Gasket
p/n: 30-0050-54
Gasket, cowl vent. Perfect reproduction, high quality, original configuration, not a sponge substitute.Length: 14.0 inches. Width: 5.75 inches.
Front Stabilizer Bushing
p/n: 30-0123-33
Bushings, front stabilizer mounting bracket. Fully molded rubber.
Suspension bushing
p/n: 30-0341-36
Bushing, insulator, upper support arm, outer above steering knuckle support. Four (4) piece set.
Hood Corner Pad
p/n: 30-0037-42
Pads, hood front corner. Metal core, retained by single rivet.Length: 1.75 inches. Width: 1.375 inches.
Taillight Mounting Pad
p/n: 30-0318-15
Gaskets, taillight mounting, with proper beading and shape as original. For all models with center license mounting. Length: 7.125 inches.
Door Bumper
p/n: 34-0305-71
Bumper assembly, front door hinge, upper, stop. Two (2) per car, steel core as original.Height: .6875 inches.
Suspension bushing
p/n: 30-0339-36
Bushing, insulator, front suspension lower support arm, inner. Four (4) piece set.
Suspension bushing
p/n: 30-0335-36
Bushing, insulator, torque arm to frame at rear. Four (4) piece set.
Brake and Clutch Pedal Pads
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Prop shaft retainer bushing
p/n: 70-2268-27
Retainer, intermediate bearing. All models with two piece driveshafts.
Bumper Grommet
p/n: 30-0039-28
Grommets, front or rear bumper. On models without trunk racks. Two (2) pair used per car if needing both front and rear bumper grommets.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Heel plate
p/n: 70-3608-88
Heel plate to protect driver's side floor carpet. Identical to original. Only for models with carpet.
Engine Mount Pad
p/n: 30-0267-11
This Engine Mount Pad pair is used as a support insulator at the timing gear cover. Correct design and rubber compound.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Rear Bumper Grommet
p/n: 30-0067-29
Grommets, rear bumper. Length: 4.3125 inches. Width: 2.6875 inches.
Front Spring Bumpers
p/n: 30-0120-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. Self retaining type bumper manufactured with top quality materials.
Hood Corner Pad
p/n: 30-0010-42
Pads, hood rear corners. High quality rubber with metal core as original.Length: 3.4375 inches. Width: 1.875 inches.
Front Spring Bumpers
p/n: 30-0087-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. Self retaining type bumper manufactured with top quality materials.
Accelerator Pedal Service
p/n: 30-0474-41
Pad, accelerator pedal. Revulcanization service only.Length: 9.625 inches. Width: 1.9375 inches.
Axle Rebound Pad
p/n: 30-0371-32
Bumper, rear frame to axle rubber. Two (2) per car.Length: 5.1875 inches. Width: 2.0625 inches.
Transmission Mount Service
p/n: 30-0316-24
Insulator assembly, transmission support. Revulcanization service only. Send in your old core for service.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Side Roof Rail Weatherstrip
p/n: 30-0031-65
Weatherstrip, side window. Fits metal channel. Made of high-quality EPDM rubber. Twelve (12) foot strip.
Spring Shackle Bushing
p/n: 30-0344-32
Bushing, rear spring and shackle. One and one eighth (1-1/8) inch diameter with nine sixteenths (9/16) inch hole. One set contains twelve (12) pieces.
Front Suspension Bumper
p/n: 30-0489-32
Bumper, front suspension (inside of coil spring). Made with three eighths (3/8) inch stud as original.
Front Door Vent Window Weatherstrips
p/n: 30-0018-55
This four (4) piece Front Door Vent Window Weatherstrips contain the upper and lower seals that cover the top, front, and bottom of the vent window. All of the pieces are designed from original parts for a precise, factory fit.
Windshield Gasket
p/n: 30-0280-50
This Windshield Gasket mounts around the full perimeter of the front glass and has the divider bar molded directly into it for a precise, factory fit.
Engine Mount Service – Revulcanization Only
p/n: 30-0325-11
This Revulcanization Service Only is designed to restore your Rear Engine Support Mount to a like new original condition. Service requires your metal core. Please call or email for more service details and ordering.
Running Board Trim Strips
p/n: 30-0396-49
This Running Board Trim Strip set is designed from the original part for superior fitment, finish and function. Manufactured with quality stainless steel and with retaining clips.
Running Board Matting
p/n: 30-0428-49
This reproduction Running Board Matting pair is designed from the original part for superior fitment, finish and function. Fully molded with crowned blocks. Top quality rubber, flawless detail. No splicing or butting required.