Hood to radiator weatherstrip
p/n: 60-0670-42
Weatherstrip or seal, hood panel to radiator support. Correct extruded rubber strip. Used on vehicles with factory A/C.
Hydraulic Pump Mounting Pad
p/n: 70-0946-67
This Hydraulic Pump Mounting Pad is designed from the original part for superior fitment and function. For folding top hydraulic pump mount. Special design to hold pump mounting bracket to floor pan. Four (4) pads needed per car. Height: 1" inch.
Inner Fender Seal
p/n: 60-0667-45
Seal, inner fender to frame. Extruded rubber strip replacement. Available by the foot.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Parking Light Lens Gasket Set
p/n: 70-4463-36
This Parking Light Lens Gasket set is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the Parking Light Lens and the Parking Light Housing or Bezel.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0773-WT
This Peel-N-Stick Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Power Top Cylinder Spacer
p/n: 70-0822-67
This Power Top Cylinder Spacer is used as the folding top power cylinder support. Molded from 100% EPDM dense rubber for durability. Four (4) spacers used per car.
Quarter Window Lock Pillar Fillers
p/n: 60-0602-79
This Quarter Window Lock Pillar Filler pair seals the bottom of the rear side window, and may also be known as a u-jamb or door jamb seal. Fully molded authentic rubber construction with brass metal core.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Rear Bumper To Body Filler
p/n: 60-0359-30
This dense rubber Rear Bumper To Body Filler is designed from the original part for a superior fitment. The part is approximately sixty-six (66) inches long and fits between the vehicle body and the rear bumper.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Rigid Run Channels
p/n: 70-0347-58
This Rigid Run Channel pair is stainless beaded and mohair-lined to help eliminate window rattles and provide a smooth sliding surface for glass movement. Also works to protect the glass.
Running Board or Inner Fender Splash Filler
p/n: 60-0288-45
This eight (8) foot Splash Filler strip is used for the running board apron to body or fender splash panels anti-rattle filler. This filler strip is top-quality EPDM sponge rubber to accept rivets or retaining screws.
Shock Absorber Bushing
p/n: 70-0547-32
This Shock Absorber Bushing is manufactured with high-quality EPDM rubber to OEM specifications. The bushing is the double cone style. Designed from original part to ensure proper fit.
Shock Absorber Grommet
p/n: 60-0235-33
This Shock Absorber Grommet is fully molded and designed from the original part for superior fitment and durability. The grommet the plain cylinder type with flat ends for shock absorber mounting.
Shock and Stabilizer Grommet
p/n: 70-0274-33
This Shock and Stabilizer Grommet is fully molded using EPDM dense rubber. Designed from original with locating collar. Eight (8) required per car.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.
Solenoid Plunger Boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Splash Apron / A-Arm Dust Shield
p/n: 70-2800-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Steering Column Gasket - Automatic Transmission
p/n: 70-4467-36
This Steering Column gasket is designed from the original part for superior fitment and sealing. Gasket is machine cut from quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Taillight Gasket
p/n: 60-0693-15
Seal, taillight bezel. Correct profile and long lasting material. Six (6) strips cut twelve and three fourths (12-3/4) inches long.Length: 12.75 inches.
Taillight Lens to Bezel Gaskets
p/n: 70-4464-69
This Taillight Lens to Bezel Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the taillight lens and taillight housing bezel.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Transmission Mount Service
p/n: 60-0465-25
Transmission mount. One (1) per car. Revulcanization service only.Length: 5.75 inches.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Vent division bar weatherstrip
p/n: 60-0636-56
Front vent window division post seal. Fully molded with metal core and attaching tabs. This part fits opposite the glass run channel and seals the vent window when the vent is closed. See Front door vent weatherstrip for main rubber seal.
Window Felt Beltline Weatherstrips
p/n: 80-0215-57
This is an Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This eight (8) piece set includes inner and outer window felt beltline weatherstrips for each side window and quarter window.
Window Regulator | Accelerator Rod Seal
p/n: 60-0652-70
This Window Regular | Accelerator Rod Seal is used as a front window regulator seal for 1955-60 passenger cars with electric windows and for 1957-62 Corvette models. Used as an accelerator rod through toeboard seal for 1955-62 V8 only Corvettes.
Window Stop Stem Bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Window Stop Stem Bumper
p/n: 33-0540-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. Designed as a window stop cushion for front and rear door, rear side and quarter windows as required.
Wiper Motor Mounting Gasket
p/n: 70-4466-53
This Wiper Motor Mounting gasket is designed from the original part for superior fitment and sealing. Gasket is machine cut from quality dense rubber to authentic original dimensions. This gasket fits to mount and isolate the wiper motor to the firewall / cowl.