Front Suspension Bumper
p/n: 20-0034-32
Bumper, front suspension upper arm. Three eighths (3/8) inch by three fourths (3/4) inch bolt, twenty four (24) threads.
Door Bumper
p/n: 70-2365-71
Bumpers, rear door opening. Proper configuration with slots for retaining screws like original.
2-1/2" Black Bow Drill Cloth Tape
p/n: 70-1172-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Body Mounting Pad
p/n: 70-2165-48
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. Used on the bottom of most mounting locations.
Cowl Drain Gutter Hose Grommet
p/n: 33-0329-54
This Cowl Drain Gutter Hose Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Decklid Top Cover Weatherstrip
p/n: 70-3922-67
This Decklid Top Cover Weatherstrip is designed from the original part for a superior fitment and seal. This seal mounts around the full perimeter of the soft top storage compartment.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Firewall To Hood Weatherstrip - Cowl Lacing
p/n: 20-1860-42
This Firewall To Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the closing hood and the vehicle firewall.
Fuel Tank Filler Neck Grommet
p/n: 20-1298-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This fully molded flexible rubber grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Hood to Cowl Weatherstrip
p/n: 20-1310-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An reproduction using the correct profile dense rubber extrusion.
Hood to Cowl Weatherstrip
p/n: 70-3959-43
This Hood To Cowl Weatherstrip has the proper rubber cross section and made from top quality rubber to ensure durability. Designed from the original part for a superior fitment and seal.
Solenoid Plunger Boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Window Regulator | Accelerator Rod Seal
p/n: 60-0652-70
This Window Regular | Accelerator Rod Seal is used as a front window regulator seal for 1955-60 passenger cars with electric windows and for 1957-62 Corvette models. Used as an accelerator rod through toeboard seal for 1955-62 V8 only Corvettes.
Glovebox Door Link Grommet
p/n: 70-0968-88
This Glovebox Door Link Grommet is designed from the original part for superior fitment and function. Grommet works to cushion the glovebox door closure.
Window Pinchweld Seal
p/n: 20-1739-52
Seal, garnish molding to dash rubber. Eighty six (86) inches long. Replaces factory #B9A-7003127.
2-1/2" Tan Bow Drill Cloth Tape
p/n: 70-1173-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
Folding seat bumper
p/n: 70-2579-88
Bumper, folding front seat frame rest cushion. Manufactured from dense rubber with a molded in metal retaining washer. Two (2) used per car.
Glovebox Door Check Grommet
p/n: 27-0105-88
This Glovebox Door Check Grommet is manufactured out of 100% EPDM dense rubber for durability. Designed from original for a proper fit.
Cowl Ventilator Grille Weatherstrips
p/n: 20-1886-54
These Cowl Ventilator Grille Weatherstrips are used to reduce noise from the cowl top ventilator grille. These U-Shaped stripes are designed for a superior fitment and seal.
Exhaust Tailpipe Hanger Strap
p/n: 60-0308-13
This Exhaust Tailpipe Hanger Strap is made from high-quality rubber for a precise, factory like fit for your classic vehicle. Muffler/tailpipe system, reproduction strap type is manufactured to OEM specifications.
Parking Light Lens Gaskets
p/n: 20-1239-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Lens and the Parking Light Housing or Bezel.
Parking Light To Fender Mounting Pads
p/n: 20-1240-16
This Parking Light To Fender Pad pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the parking light assembly and the vehicle fender on each side.
Tie Rod Dust Covers
p/n: 20-2484-36
This Tie Rod Dust Cover, drag link seal, is sold as a four (4) piece set. The seals are designed from originals for proper fitment.
Window Sash Channel
p/n: 20-1909-62
This Window Sash Channel is designed from the original part for superior fitment and seal. Thirty-four and three-fourths (34-3/4") inch long EPDM rubber extrusion that goes between glass and metal sash lift channel. One (1) roll required per window.
Hood Bumper
p/n: 25-0076-42
This Hood Bumper is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Six (6) required per car.
Hood Bumper
p/n: 27-0098-42
Bumper, hood front to radiator ledge, adjustable. Includes plated bolt and rubber cushion.Length: 2.1875 inches.
Fuel Filler Neck Grommet
p/n: 20-0585-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Outside Door Handle Mounting Pads
p/n: 20-0568-69
This Outside Door Handle Mounting Pad set is designed from the original part for superior fitment and function. This four (4) piece molded rubber set does two (2) doors.
Door Handle Gasket Set
p/n: 27-0102-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Clutch or Brake Pedal Pad
p/n: 20-0848-22
This reproduction Clutch and/or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Axle Rebound Pad
p/n: 20-1287-32
Bumper, rear spring and axle. 1957-59: Full size Fords: Five (5) required per car (1 in center, 2 each side).
Body Mount Isolator Pad
p/n: 50-0507-48
Isolator, body mounting. Fully molded rubber. Two inches (2") outside diameter by seven eighths inch (7/8") inside hole diameter by three fourths inch (3/4") height.
Bumper Support Bar Pad
p/n: 70-0993-30
Bumper, impact bar end to body, for rear bumper. Fully molded rubber. Two inches (2") length by seven sixteenths inch (7/16") width by eleven sixteenths inch (11/16") height.
Bumpers - Filler Door/Lower Door/Rear License Plate Support
p/n: 20-1302-41
A rubber Bumper pair designed from the original part for superior fitment, finish and function. Fits to the lower door and / or the fuel filler cover and / or the license plate support. Type with threaded end.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Gearshift Knob
p/n: 20-0521-24
This black column shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This sphere shaped reproduction part is a direct push on replacement for that broken, aged-out original knob.
Gearshift Knob
p/n: 20-0629-24
This white column shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This sphere shaped reproduction part is a direct push on replacement for that broken, aged-out original knob.
Strut Rod Bushing
p/n: 50-0522-27
Bushing, strut rod at drive shaft tube. Two (2) per car required.Length: 1.65625 inches.
Body Mount Isolator
p/n: 70-2232-48
Isolator, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by fifteen sixteenths inch (15/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body Mounting Pad
p/n: 70-2233-48
Pad, body mounting to chassis. Fully molded rubber. One and seven eighths inch (1 7/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter by nine sixteenths inch (9/16") height.
Body Mounting Pad
p/n: 70-2234-48
Pad, body mounting to chassis. Fully molded rubber, square type. Six (6) or more are used per car. Two and three sixteenths inch (2 3/16") square by three fourths inch (3/4") inside diameter hole by one half inch (1/2") inch height.
Hood Bumper
p/n: 50-0489-42
Bumper, hood to fender ledge. Number required varies. Molded rubber type.Width: 1.5 inches. Height: 1.0 inches.
Hood to Fender Bumper
p/n: 60-0542-42
This Hood to Fender Bumper set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
License lens gasket
p/n: 50-0357-17
Gasket set, rear license light assembly. One (1) rubber ring and one (1) cork rubber gasket comprise set.
Tailgate Bumper
p/n: 20-0694-45
These Tailgate Bumpers are sold as pair. The bumpers fit in brackets and comes with chains.
Tailgate Bumper
p/n: 70-1910-87
This Tailgate Bumper is designed from the original part for superior fitment, finish and function. This station wagon tailgate bumper is commonly used on GM station wagon models.
Body / Cowl to Fender Seals
p/n: 70-3075-43
This Body / Cowl to Fender Seals pair is designed from the original part for superior fitment and function. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions.
Rear View Mirror Mounting Pad
p/n: 70-3082-70
This single Rear View Mirror Mounting Pad To Door gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is for one (1) door mounted rear view mirror.
Parking light lens gasket
p/n: 20-0608-16
Gaskets, parking light lens. Useage: 1957-63: Style-Side Trucks 1957-58: F100-600 Trucks
Taillight Lens Gaskets
p/n: 20-1230-15
A four (4) piece Taillight Lens Gasket set designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lens and taillight housing bezel.
Window Stop Stem Bumper
p/n: 33-0622-62
This Window Stop Stem Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.