Mounting pad and seal, windshield frame to cowl. Approximately forty two and one half (42-1/2) inch overall length.
Weatherstrip, windshield lower. Height: .5625 inches.
Weatherstrip, split windshield, fully molded to include end caps for lower glass frame, especially tooled for these cars.
Seal, windshield, lower.Length: 43.50 inches.
Mounting pad, windshield lower frame to body. Forty eight (48) inches long. Molded in two (2) parts with joint in center. Canvas base as original.
Weatherstrip, cowl to windshield. Glass frame. Three (3) piece set of right and left molded ends plus center section of soft yielding rubber.
Mounting pad, windshield frame to cowl. Molded in two (2) parts with joint in center. Canvas base as original.Length: 48.0 inches.
This windshield gasket weatherstrip comes in a ten foot (10') strip and mounts around the full perimeter of the front glass. It has the slot to accommodate the outer edge's decorative molding and the ends may require trimming and bonding for installation.
Weatherstrip, windshield glass frame to stanchion. Seventeen (17) inches long, to proper cross section.Length: 17.875 inches.
Pad/Seal, windshield frame, lower. Forty six (46) inches overall.Length: 46.0 inches.
12 (twelve) foot strip of windshield weatherstrip channel. Seals windshield glass to body and protects interior of vehicle.
Weatherstrip, windshield side, inner frame to windshield post, upper, fits dovetail slot in swinging glass frame.
Weatherstrip, windshield inner frame to windshield post. Made from top quality molded EPDM rubber. Approximately eleven (11) inches long.
Filler or plug, windshield upper corner.
This Windshield Gasket mounts around the full perimeter of the front glass. It has the slot to accommodate the outer edge's decorative molding and the ends may require trimming and bonding for installation.
Bumpers, windshield frame to pillar. Closed bodies with split windshield. 2 rights and 2 lefts required per car. Four (4) piece set.Length: 2.25 inches.
Weatherstrip, windshield to dash (anti-glare). 2 piece set.
Pads, windshield stanchion base, mounting. Good copy.Length: 4.375 inches.
Pads, windshield stanchion mounting. Perfect copy, including concave bottom face to properly fit cowl, right and left.Length: 3.125 inches.
This three (3) piece Swing-Out Windshield Weatherstrip Set is designed for superior fitment, finish and function. Three (3) piece set, consisting of stationary weatherstripping for bottom and sides.
Mounting pad. Windshield post in open cars. 6 cylinder
Pad, windshield lower weatherstrip, retainer-to-cowl.Length: 44.0 inches. Width: 1.5625 inches.
Pad, windshield stanchion mounting. Molded left and right. Varsity Roadster only.
Seal, windshield frame. Fits original frames only. Replaces factory #48-7103110.
This Swing-Out Windshield Weatherstrip comes in an eleven (11) foot strip. The seal slides into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Pads, lower windshield post, approximately two and one half (2-1/2) inches square by one fourth (1/4) inch thick.Length: 2.5 inches. Width: 2.5 inches.
Seal, windshield outer trim. Four (4) piece set for top and bottom of division post trim and for right and left lower corners of windshield panels.
Set, windshield chrome plastic molding. Includes: one (1) windshield molding strip (cit to fit), one (1) pair upper corner molding, and one (1) pair lower corner molding. Five (5) piece set.
This Windshield Frame To Body Weatherstrip mounts around the full perimeter of the front glass and has properly molded corners for a precise, factory fit. For Ford 3-Window 2-Door Coupes ONLY.
This Windshield Gasket comes in a four (4) foot strip and is for horizontally split windshields. The slot fits on the upper half and the projecting edge meets the lower half when the windshield is closed.
Pad, windshield side arm-to-cowl.Width: 3.1875 inches.
Pad, windshield side arm-to-cowl, right and left. Replaces #370356.
End caps, for horizontally divided windshield weatherstrip, right and left, to seal ends of our #19-0005-52 weatherstrip that goes across windshield.
Weatherstrip, windshield garnish molding on lower windshield post. Molded rubber replacement for #469222-3.
Filler, windshield division channel ends, upper and lower. Two (2) piece set.
Seal, windshield frame to body. Replaces factory #40-7003110.
This Windshield Frame To Body Seal is made from the original design with quality materials for a precise, factory fit. This part installs around the perimeter of the windshield frame.
This Three Piece Windshield Reveal Molding is designed from the original part for superior fitment. This part fits across the top and on each side of the windshield. The part is made with top quality materials and with the proper molding profile for an exact fit and finish.
This three (3) sided, One Piece Windshield Reveal Molding is designed from the original part for superior fitment. This part fits across the top and on each side of the windshield. The part is made with top quality materials and with the proper molding profile for an exact fit and finish.
Pads, windshield post. Replaces factory #B-7603105.
This Window Weatherstrip is made of a high-quality EPDM dense rubber extrusion. The weatherstrip is used for the upper scraper seal.
This Removable Roof Front Seal is designed from the original part for superior fitment and sealing. This part fits on the rear of the metal cab roof and seals against the removable fiberglass top when the top is placed on the vehicle.
This Windshield Frame Upper (Header) Weatherstrip is designed from the original part for superior fitment and sealing. This windshield frame upper weatherstrips mounts to seal between the windshield frame and hardtop of the vehicle. Made of a high-quality EPDM rubber as the original.
This Windshield Trim To Glass Weatherstrip pair for convertibles is designed from the original part for superior fitment, finish and function. These LH and RH windshield trim weatherstrips go between the windshield and the windshield molding.
This four (4) piece Windshield Wiper Pivot Gasket set is designed from the original part for superior fitment and seal. This reproduction gasket is die cut from original style EPDM rubber for an authentic fitment, finish and function.
Pads, windshield post. Replaces factory #48-7603105.
This Windshield Upper Reveal Molding is designed from the original part for superior fitment. This part fits across the top of the windshield. The part is made with top quality materials and with the proper molding profile for an exact fit and finish.
Molding, upper windshield corner. Replaces factory #D7TZ-10030A42-B.