Boot, distributor dust and moisture. Original equipment, exact copy. V-16 only.
Pad, horn grille mounting below headlight in fender.
Pad, horn grille housing mounting. Five and one fourth (5-1/4) inch by seventeen (17) inch overall.
Mounting pad, horn grille housing.
A six (6) piece Door Conduit set for the front door electric window wires or power lock vacuum lines. The set includes two (2) hoses and two (2) pairs of grommets.
This Door Conduit Set is designed from the original part for superior fitment and function. Conduit contains the front door electric window wires and/or power lock vacuum lines. Set includes two (2) hoses and three (3) pair of grommets. Length: 12.0 inches.
Sleeve, spark plug wires from distributor to wiring tube, rubber only.
Bumpers, horn cover. Rubber with brass core construction like original.Length: 4.0 inches. Width: .625 inches.
Sleeve, plug wire tube to distributor cap. One (1) pair required per car.Height: .9375 inches.
Hose, hydraulic window lift. Eighteen (18) inches long.
Pad, starter pedal. Rectangular outline, curved as original to fit oval steel pedal core, proper tread pattern to match other pedals.
Mount, antenna, insulator shell assembly, running board. Revulcanization service only. Use in conjunction with our # 50-0305-21.
Filler strip, radiator brace rods. Retains ignition wire and thermometer tube in hollow brace rods. Thirty (30) inch strips.
Boot, starter rod through toe board, tall style. Brown rubber. For black see our #40-0257-21. One and five eighths (1-5/8) inch high with steel bushing.
Boot, starter rod through toe board, short style. Brown rubber. For black see our #40-0258-21. One and one fourth (1-1/4) inch high with steel bushing.
Starter rod boot
Starter rod boot
Cover, top of horn relay.
Boot, spark plug wire, at spark plug. All original textures and details.Length: 2.0 inches.
Boot, hydraulic window lifting cylinder, front and rear.
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
Grommet, ignition cable.Length: 2.125 inches. Width: 1.50 inches.
Boot, generator splash shield rubber.
Grommet, horn mounting bracket.Width: 2.125 inches.
Pad, starter pedal, snap over cover with tread pattern matching other pedals.Length: 2.25 inches.
Pad, starter pedal. Excellent quality with detail and workmanship as found in original.
Conduit (double rubber hose), body to door, for hydraulic and electrical lines to power window.
Cover, starter cable terminal post inside to frame. Full detail and molded as original part.
Grommet, horn wire exit from horn motor cover. Eleven thirty seconds (11/32) inch inside diameter. Two (2) per car.
Grommet, two (2) hole, for hydraulic pump through sheet metal.Length: 1.9375 inches. Width: 1.125 inches.
Grommets, horn wire exit from horn motor cover.
Separator, horn contact. For standard or non-flexible wheel.
Shield, generator splash.
This is a three (3) piece Horn Button Contact set which is designed from the original part for superior fitment and function. Renews the operation of the steering wheel horn blowing ring.
End loop, radio antenna. Cord reinforced rubber with metal grommet. Mounted on running board on some models.
Grommet for trumpet horn wire through motor cover. Close reproduction. Two (2) per car.
This Antenna Mount Pad pair is designed from the original part for superior fitment and seal. For rear mounted twin (dual) antennas. See our 32-0390-21 for insulating Antenna Grommet pair.
Cushion ring, horn button contact, upper.
Nipple, coil wire to distributor at coil end.
Cushion, standard steering wheel horn button contact. Two and one half (2-1/2) inch diameter.
Button, starter pedal rod. Brown rubber.
This Antenna Mount Pad is a high-quality reproduction of the original factory part. This mount pad installs between the antenna mounting base and fender to protect the painted surface.
Mount, radio antenna wire, under running board. Found on several models with factory type antennas that mount under the running board.
Pad, roof mounted antenna gasket. Models with antenna mounted above center of windshield.
Boot, running board antenna wire connection.
Ring, horn button contact. Accessory banjo steering wheel. Four and one eighth (4-1/8) inch outside diameter.
Pad, starting motor foot switch. Rubber construction, internal threaded as original.Height: 1.25 inches.
Cushion, horn blowing button.Height: 1.0 inches.
Mounting pad, power window die cast bezel. Used under 4 way switch, typically found on drivers door.Width: 2.0 inches.
Edge liner, battery carrier cover.Length: 42.0 inches. Width: .25 inches. Height: .6875 inches.