Hood Bumpers & Fittings
Hood to fender weatherstrip
p/n: 70-2728-42
Seal, hood to fender. Mounts on fender at hinge area inside hood opening. Fits around hood hinge assembly to isolate engine compartment from car interior. Replaces factory #E3SZ-16071-B, E3SZ-16072-B.
Hood hinge top strap pivot
p/n: 70-0045-42
Pivot, hood hinge top strap. Cold rolled steel as original. Furnished in a four and one half (4-1/2) foot strip long enough for all models.
Hood corner pad
p/n: 17-0036-42
Pads, hood front corners, exact copy with metal core as original. Right and Left.Width: 2.50 inches.
Hood to cowl weatherstrip
p/n: 30-0138-42
Guard strip, hood to cowl. Brass core with molded integral hood rest.Length: 14.875 inches.
Hood to cowl bumper
p/n: 30-0223-42
Bumpers, hood to cowl. Brass core, one and one half (1-1/2) inch by four and one half (4-1/2) inch.Length: 4.50 inches. Width: 1.50 inches.
Hood center protector
p/n: 70-0342-42
Protector, hood center. Brass core as original threaded to fit original screws.
Hood Bumper
p/n: 40-0118-42
Bumpers, hood top panel to side panels. Four (4) piece set with brass core as original. Four (4) per vehicle.
Hood corner pad
p/n: 30-0130-42
Pads, hood front corners. Large self prong type with metal core molded left and right.Length: 3.375 inches.
Hood bumper
p/n: 70-0013-42
Pads, hood hold-down clamp, mount on clamp swivels to hold hood corners in. Set of four (4) rubber pads in solid brass, chrome plated cups.
Hood corner pad
p/n: 17-0035-42
Pads, hood rear corners, exact copy with metal core as original. Right and Left (reversible).Width: 2.50 inches. Height: 1.75 inches.
Hood corner pad
p/n: 30-0011-42
Pads, hood front corners, large type. Molded right and left with metal cores and double tab retainers.Length: 3.1875 inches. Width: 2.125 inches.
Hood corner pad
p/n: 30-0059-42
Pad, hood rear corner. Molded left and right with a metal core.Length: 2.50 inches. Width: 1.75 inches.
Hood bumper
p/n: 40-0313-42
Bumper, hood panel assembly. Same as our #40-0164-42. (except vulcanized to brass cores).Length: 1.375 inches. Width: 1.3375 inches.
Hood ventilator wedge pad
p/n: 70-0317-42
Wedge pads, hood side ventilators. Fourteen (14) piece set.
Hood ventilator bumper kit
p/n: 70-0011-42
Pad set, hood vent door open limit. Set of twenty (20) pads for one (1) hood, including split rivets for installing.
Hood corner pad
p/n: 30-0183-42
Pads, hood corners. Right and left replacement. Brass core, integral holding tabs.Length: 3.125 inches.
Hood corner pad
p/n: 30-0088-42
Pad, hood front corner. Metal core, retained by four (4) tabs.Length: 3.25 inches. Width: 1.25 inches.
Hood corner pad
p/n: 30-0010-42
Pads, hood rear corners. High quality rubber with metal core as original.Length: 3.4375 inches. Width: 1.875 inches.
Hood corner pad
p/n: 25-0052-42
Pad, hood corner front or rear. Made with metal core.Length: 2.25 inches. Width: 1.5 inches.
Hood Vent Bumper
p/n: 33-0053-42
Bumper, hood ventilator door, self retaining. Five sixteenths (5/16) inch diameter, forty eight (48) piece set.
Hood corner pad
p/n: 60-0042-42
Pads, hood corners, right and left. Four (4) piece set.Width: 1.125 inches. Height: 1.125 inches.
Hood corner pad
p/n: 50-0290-42
Pads, hood corners, rear, right and left, metal cores.Width: 1.5 inches. Height: 1.25 inches.
Hood corner pad
p/n: 50-0452-42
Pad, hood corners, rear. Molded left and right with metal core.Width: 1.625 inches. Height: 1.375 inches.
Hood to fender weatherstrip
p/n: 70-1016-42
Seal, hood to fender. Exact profile rubber extrusion. Two (2) strips sixteen (16) inches long. Used on vehicles with A/C.
Hood corner pad
p/n: 60-0399-42
Bumpers, hood front corners. Right and Left with metal cores.Width: 1.625 inches.
Hood corner pad
p/n: 40-0089-42
Pads, hood front corners. Rubber with metal core as original.Length: 1.4375 inches.
Hood corner pad
p/n: 60-0053-42
Pads, hood rear corners, right and left. Metal core as original, with metal tabs for securing to hood.Width: 1.3125 inches. Height: 1.50 inches.
Hood corner pad
p/n: 30-0225-42
Pads, front and rear hood corners, brass core, right angle.Length: 2.625 inches. Width: 2.625 inches.
Hood to cowl weatherstrip
p/n: 30-0049-42
Scuff pad, hood to cowl. Superior duplication of part with better rubber than original.Length: 8.25 inches.
Hood corner pad
p/n: 25-0029-42
Pads, front hood corners, right and left. Brass core as original, with self-held steel tabs.Length: 1.75 inches. Width: 1.3125 inches.
Hood corner pad
p/n: 25-0030-42
Pads, rear hood corners, right and left. Brass core as original, with steel self-held tabs.Length: 1.75 inches. Width: 1.1875 inches.
Hood bumper
p/n: 50-0326-42
Bumper, hood side pilot. Four (4) piece set required per car. Steel washer vulcanized inside rubber.
Hood Louver Corner Stop
p/n: 33-0129-42
Corner stop, hood louver, self-holding, original size and profile, fits one fourth (1/4) inch hole in sheet metal.
Hood corner pad
p/n: 70-0047-42
Pads, hood corners, rear. Original style with metal core and metal fastening tabs.
Hood corner pad
p/n: 50-0036-42
Pads, hood corners, front. Original type with metal core and retaining tab.Width: 1.625 inches.
Hood corner pad
p/n: 27-0032-42
Pads, hood rear corners, right and left. Metal core as original with integral mounting tabs for hole in hood corner.Width: 1.4375 inches. Height: 1.
Hood corner pad
p/n: 40-0127-42
Pads, hood corners, brass core. Approximately 80 degree angle. Integral tabs for installing.Length: 1.50 inches.
Hood corner pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Hood corner pad
p/n: 60-0052-42
Pads, hood front corners, right and left. Metal core as original, with metal tabs for securing to hood.Width: 1.0 inches. Height: 1.25 inches.