Side Window Parts, Other
Push-Out Window Gasket Set
p/n: 90-0153-81
This Push-Out Window Gasket Set is for the Side OR Rear push-out windows. This three (3) piece kit includes the push-out window frame gasket and the inner and outer window glass weatherstrip.
Windshield A-Pillar Post Weatherstrips
p/n: 82-0155-68
This Windshield A-Pillar Post Weatherstrip pair is designed from the original part for superior fitment and seal. These windshield frame weatherstrips install on the A-pillar post to seal the front edge of door window to the body.
Push-Out Window Frame Gasket
p/n: 70-4132-81
This Push-Out Window Frame Gasket is for the side OR rear push-out windows and has properly molded corners for a precise, factory fit. Up to six (6) used per van.
Hinge Post Weatherstrip Seals
p/n: 20-1148-62
Hinge Post Weatherstrip Seals for upper front corner of door window.
Door conduit
p/n: 60-0653-21
Conduit, front door electric window wires and/or power lock vacuum lines. Set includes two (2) hoses and three (3) pair of grommets.Length: 12.0 inches.
Door Conduit Set - Wiring - Vacuum Hoses
p/n: 60-0655-21
A six (6) piece Door Conduit set for the front door electric window wires or power lock vacuum lines. The set includes two (2) hoses and two (2) pairs of grommets.
Rear Door Window Upper Seal
p/n: 70-4198-79
This Rear Door Window Upper Seal pair is designed from the original part for superior fitment and sealing. This rectangular shaped seal pair mounts to the rear door at the upper front and over the rear side window.
Division Bar Grommet
p/n: 70-3132-62
Grommets, rear door vent divider post, upper and lower, right and left. 4 piece set.
Side Window Rear Vertical Seals
p/n: 82-0158-68
This Side Window Rear Vertical Seal pair is designed from the original part for superior fitment and seal. This part attaches to the rear vertical B-post edge of the side windows for coupe and hatchback models.
Front of Door to Window at Beltline Seals
p/n: 70-4661-62
This Front of Door to Window at Beltline Seal pair is designed from the original part for superior fitment, finish and function. This LH and RH seal pair installs at the front corner of the side windows, near the side-view mirror.
Division Bar Grommet
p/n: 70-0483-62
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Vent frame deflector
p/n: 70-1792-62
Deflector, beneath vent frame.Length: 5.75 inches. Width: 1.0 inches.
Rear quarter window bumper
p/n: 70-0688-62
Bumper, rear quarter window on door lock pillar. One and one fourth (1-1/4) inch square with metal core. Two (2) per car.Length: 1.375 inches.
Quarter window filler
p/n: 20-3085-62
Seal assembly. Installs on body below rear quarter glass to body weatherstrip.
Upper Division Post Bumper
p/n: 70-3554-62
Bumper, upper division post. Rubber with metal cores. Both R & L sides.
Rear of Door Run Channel Seals - Convertible & T-Top
p/n: 70-4654-58
This Rear of Door Run Channel Seal pair is designed from the original part for superior fitment, finish and function. This window run channel seal fits at the end of the side window glass run channel. Molded as left and right.
Quarter window bumper
p/n: 60-0669-62
Bumper, quarter window on body lock pillar.Though we haven't been able to determine a part number, this part is used on 1951 hardtops and convertibles.
Side Window Rear Vertical Seals
p/n: 82-0157-68
This Side Window Rear Vertical Seal pair installs on the rear quarter section and seals the back edge of the door window to the body. Made from top quality rubber for durability and a like factory seal.
Body to door conduit
p/n: 70-0506-21
Conduit (double rubber hose), body to door, for hydraulic and electrical lines to power window.
Door conduit
p/n: 70-0828-21
Conduit, hydraulic line & power window wire. Front doors only. 2 pieces cut nine and one half (9-1/2) inches.Length: 9.50 inches. Height: 1.50 inches.
Roof rail filler
p/n: 70-2024-73
Seal, roof rail at quarter window. Fully molded with brass core.Length: 1.375 inches. Width: .6875 inches.
Division Bar Grommet
p/n: 70-0272-62
Grommets, rear door vent divider post, top and bottom, right and left.
Sash channel weatherstrip
p/n: 60-0690-58
Weatherstrip, sash channel. Correct extrusion. Two (2) strips cut twenty five and one half (25-1/2) inches long.
Power window switch bezel pad
p/n: 70-2137-21
Mounting pad, power window die cast bezel. Used under 4 way switch, typically found on drivers door.Width: 2.0 inches.
Window division bar filler
p/n: 70-2661-62
Filler, quarter window division bar, upper and lower. Fits into inside garnish molding between rear seat side window and rear side window.
Hydraulic window lift grommet
p/n: 70-0642-21
Grommet, window lift hydraulic line through floor panel. Single hole type (for two (2) hole type, see our #70-0643-21).Length: 1.5 inches. Width: 1.
Push-Out Window Weatherstrip
p/n: 70-4183-76
This Push-Out Window Weatherstrip mounts around the full perimeter of the glass and will flex around the window corners. A replacement for the original part offering a precise fit.
Quarter window pivot cover
p/n: 20-2787-62
Covers, fastback quarter window lower pivot, plastic. Installs on pivot rod at fiberglass interior panel.
Rear quarter window bumper
p/n: 70-1096-62
Bumper, rear quarter window. Made of molded neoprene rubber with steel washer core. Two (2) per car.Length: 1.0625 inches.
Hydraulic window lift grommet
p/n: 70-0643-21
Grommet, window lift hydraulic lines through floor panel, 2-hole style (for cars requiring single-hole style, see our #70-0642-21).Length: 1.5 inches.
Door Flipper Stop
p/n: 70-2853-62
This Door Flipper Stop is designed from the original part for superior fitment and seal. The rear flipper stop mounts inside the flipper opening at the very rear of the door flipper.
Front of Vent Window to Door Seals
p/n: 20-2786-62
These Front of Vent Window to Door Seals are installed at the front of the door and next to the door weatherstrip. Sold as a pair.
Power window switch bezel pad
p/n: 70-2136-21
Mounting pad, power window die cast bezel. Used under single window switch, typically found on front passenger door and rear windows.
Quarter Window Vertical Leading Edge
p/n: 20-1656-76
This Quarter Window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment, finish and function. This part fits Ford convertible only and is the weatherstrip that holds the quarter window glass in the frame.
Front Door To Window Seal
p/n: 20-2838-79
This Front Door to Window Seal pair is designed from the original part for superior fitment and seal. This part seals the bottom of the side window and the front door.
Hydraulic pump mounting pad
p/n: 70-0852-67
Pad, mounting, hydraulic pump. Used on models with hydraulic window lifts or hydraulic convertible top. Two (2) to three (3) required. per car.
Hydraulic pump mounting pad
p/n: 70-1610-67
Cushion mount, hydraulic pump.Width: .6875 inches. Height: 1.0 inches.
Glass Run Channel-Vent Window Delete
p/n: 70-3891-58
This Glass Run Channel is for applications where the vent window has been eliminated. One pair fits both driver (Left) and passenger (Right) side doors.
Hydraulic pump mounting pad
p/n: 70-0986-62
Mounting bracket and pad, for hydraulic pump. Number used as required.Length: 1.75 inches. Width: .8125 inches.
Channel Filler Weatherstrip
p/n: 20-2091-62
This Channel Filler Weatherstrip is designed from the original part for superior fitment and seal. This door glass to body filler seal fits in the metal channel that holds the glass piece. Sold in a 36" strips.
Channel filler weatherstrip
p/n: 20-1633-62
Seal, door glass and stainless frame special. Top, bottom, and sides for one door.Width: .375 inches. Height: .625 inches.
Channel filler weatherstrip
p/n: 20-2575-62
Seal, door glass and window frame. Retains glass in frame. Enough for one window only.
Window Stop Stem Bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.