Suspension bushing
p/n: 30-0385-36
Bushing and pin assembly, cartridge, Inlox type, front wheel lower support arm inner pin. Shipped with instructions for re-installing.Length: 5.75 inches.
Suspension bushing
p/n: 30-0386-36
Bushing and pin assembly cartridge. Inlox type, front wheel lower support arm inner pin. Shipped with instructions for reinstalling.Length: 5.75 inches.
Front spring bumper
p/n: 70-0339-32
Bumper, front spring, upper arm on frame. Rubber with heavy steel core, including five sixteenths (5/16) inch stud.
Front suspension bumper
p/n: 30-0490-32
Bumper, front suspension (inside of coil spring). Made with three five sixteenths (5/16) inch studs as original.
Front suspension bumper
p/n: 30-0228-32
Bumper assembly, front suspension inside coil spring, with five sixteenths (5/16) inch threaded studs as found originally.
Front spring bumper service
p/n: 15-0006-35
Bumper, front spring to frame. Revulcanization service only.Width: 4.625 inches.
Axle rebound pad
p/n: 70-0473-32
Pads, rear axle, springs to frame, on frame. Large pads, fully molded with screw fastening holes.
Front suspension bumper
p/n: 30-0489-32
Bumper, front suspension (inside of coil spring). Made with three eighths (3/8) inch stud as original.
Axle rebound pad
p/n: 50-0371-35
Bumper, rear axle. Revulcanization service only.Height: 3.5 inches.
Ride regulator control grommet
p/n: 70-0344-33
Grommets, ride regulator control rod through fender splash shield. Two (2) per car.Length: 5.875 inches. Width: 1.75 inches.
Rear Axle Suspension Bumper
p/n: 70-2638-35
This Rear Axle Suspension Bumper is fully molded with new rubber vulcanized to new steel cores. Used on all models with conventional spring suspension.
Front suspension service
p/n: 70-0754-32
Bumper, front suspension on shock absorber arm. Revulcanization service only.Width: 2.125 inches. Height: 3.0 inches.
Rear spring bumper
p/n: 60-0179-35
Bumper, rear spring on frame. Entire assembly with rubber vulcanized to steel as original.
Front suspension bumper
p/n: 40-0356-32
Bumper, front suspension upper arm. Vulcanized into one piece as original with steel plate and stud.
Axle rebound pad
p/n: 15-0003-35
Bumper, frame to axle, rear, with steel core as original.Width: 3.0 inches.
Rear axle bushing
p/n: 25-0081-32
Insulators, rear axle housing, upper and lower. Four (4) piece set.
Rear spring bumper service
p/n: 60-0425-32
Bumpers, rear springs to frame. Revulcanization service only.Length: 3.0 inches. Width: 2.5 inches.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Axle rebound pad
p/n: 40-0373-32
Bumpers, rear axle. Revulcanization service only.Length: 3.0 inches.
Front spring bumper
p/n: 40-0349-32
Bumper, front spring to frame. (Also known as front axle bumper).Length: 5.0 inches. Width: 2.5625 inches.
Axle rebound pad
p/n: 30-0125-32
Bumpers, rear axle spring.Length: 5.375 inches. Width: 2.75 inches. Height: 2.1875 inches.
Front suspension bumper
p/n: 30-0229-32
Bumper assembly, front suspension rebound (upper arm). Straight style with stud.
Ride Regulator Control Grommet
p/n: 70-0332-33
Grommets, ride regulator control rod through fender splash shield. Two (2) required per car.Length: 2.4375 inches. Width: 2.0 inches.
Rear spring bumper service
p/n: 60-0279-35
Bumper, rear spring on frame. Revulcanization service only.
Axle rebound pad
p/n: 13-0002-35
Pad, front axle rebound, integral dovetail retaining lug. Excellent copy.
Front spring bumper
p/n: 30-0227-32
Bumper assembly, front spring rebound (upper arm). Steel core, with treaded stud just like original.
Axle rebound pad
p/n: 70-2071-32
Bumper, rear axle impact. Fully molded with new metal core.Width: 4.625 inches. Height: 1.875 inches.
Front spring bumper
p/n: 30-0119-32
Bumper, front spring compression, lower arm. Steel core, retained by clip (not included).Height: 2.625 inches.
Axle rebound pad
p/n: 30-0054-32
Pads, rear axle rebound.Length: 5.125 inches. Width: 1.4375 inches.
Axle Rebound Pad - Rear
p/n: 10-0128-35
Axle Rebound Pad - Rear. Made from top quality rubber to ensure durability. This part is compatible with (1912 - 1915) Sterns-Knight models.
Front suspension bumper
p/n: 70-1295-32
Bumper assembly, front load compression, lower.Width: 2.125 inches. Height: 2.75 inches.
Front Suspension Bumpers - Lower Control Arm
p/n: 70-1463-32
This Front Suspension Bumper pair for the Lower Control Arm is made from high-quality EPDM rubber with a steel core for a precise, factory like fit. Width: 2-1/4" inches. Height: 1-7/8" inches.
Upper Control Arm Shaft Set
p/n: 20-1291-32
This three (3) piece Upper Control Arm Shaft set is designed from the original part for superior fitment and performance. Renew the performance of your aged and worn front suspension to restore the ride of your classic vintage vehicle.
Axle rebound pad
p/n: 30-0043-32
Pads, front axle rebound. Correct shape and design like original.Length: 3.625 inches. Width: 2.125 inches. Height: 2.125 inches.
