Fender & Fender Skirt Edging
Rumbleseat step pad
p/n: 40-0412-44
Step pad, rumbleseat upper, with "P" logo. Fully molded with core and mounting stud.Height: .625 inches.
Rumbleseat step pad
p/n: 25-0018-44
Step, rumbleseat fender with molded-in studs.Length: 6.375 inches.
Body to Fender Seal
p/n: 60-0001-45
This Body to Fender Seal pair installs on the right and left of the front body to fender. Length: 22.0 inches.
Front Fender Cushion Strip
p/n: 16-0003-44
Cushion strip, front fender to running board, close reproduction. Length: 17.75 inches.
Front Apron Crossbar Grommets
p/n: 70-1131-45
This Front Apron Crossbar Grommet pair is designed from the original part for superior fitment, finish and function. Width: 3-1/2" inches. Height: 3-1/2" inches.
Front apron crossbar grommet
p/n: 70-1130-45
Grommets, front splash apron crossbar.Width: 3.5 inches. Height: 3.6875 inches.
Crown molding mounting pad
p/n: 50-0244-44
Mounting pads, rear fender crown molding. Requires two (2) per car.Length: 40.625 inches.
Front Fender Seal
p/n: 30-0189-44
Liners, front fender to running board. Reversible right and left like original. Length: 15.0 inches.
Fender to Radiator Seal
p/n: 40-0085-44
This Fender to Radiator Seal is molded out of EPDM rubber Overall length is 11.25 inches.
Front Fender Seal
p/n: 30-0264-44
Liner, front fender to running board. Reversible right and left replacement. Length: 15.50 inches.
Front apron crossbar grommet
p/n: 30-0040-44
Grommets, front apron crossbar. Molded left and right just like original.Length: 3.625 inches. Width: 3.625 inches.
Rumbleseat step pad
p/n: 40-0124-44
Pad, rumbleseat step, with "Dodge" logo, slip over type to fit old steel core. Perfect detail and lettering.Height: .50 inches.
Rumbleseat step pad
p/n: 40-0012-44
Pad, rumbleseat step bears Chrysler medallion logo in center.Height: .50 inches.
Fender Skirt Edge Seals
p/n: 70-0897-44
Fender Skirt Edge Seal pair. Length: 60.0 inches. Width: 5/8 inches.
Fender welting 1/4" bead 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five
Fender welting 50ft chrome
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting with 3/16 Bead - 50 Ft. Roll
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Fenderskirt Edge Seal
p/n: 70-0790-44
Fenderskirt Edge Seal - Two (2) strips six (6) feet long. Length: 72.0 inches. Width: 0.375 inches.
Fender Skirt Edge Weatherstrips
p/n: 70-0055-45
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Fenderskirt edge seal
p/n: 25-0092-44
Seal, fender skirt. Two 5 foot lengths of extrusion.Length: 60. inches. Width: .9375 inches.
Rumbleseat step pad
p/n: 40-0353-44
Pad, rumbleseat step, with "DS" logo. Fits old bracket and bezel. See our #40-0055-44 also.Height: .50 inches.
Rumbleseat step pad
p/n: 40-0209-44
Pad, rumbleseat step slip over style for original core, "DB" logo.
Shoe scraper mounting pad
p/n: 60-0325-45
Pad, mounting, boot scraper-to-front fender, right and left.Width: 3.25 inches.
Fenderskirt Edge Seal
p/n: 70-0154-45
Seal, fenderskirt edge, exact copy, trim notch for skirt lock at installation. Compare sketch with your original to be sure. Two (2), five (5) foot strips.
Fenderskirt edge seal
p/n: 25-0102-44
Seal, fenderskirt. Two 5 foot lengths of extrusion.Length: 60.0 inches. Width: .625 inches.
Fenderskirt edge seal
p/n: 70-0289-45
Seal, fenderskirt edge. Good quality and workmanship, see sketch for comparison. Ten (10) foot strip.Length: 120.0 inches. Width: .1875 inches.
Rumbleseat step pad
p/n: 40-0055-44
Pad, rumbleseat step, with "DeSoto" logo, full slipover type to fit old carcass and outer trim ring. See also our #40-0353-44.Height: .50 inches.
Fenderskirt edge seal
p/n: 70-2557-45
Sealing strip, fenderskirt edge. Two (2) strips approximately fifty (50) inches long for both sides of car. Original profile and appearance.
Access hole plug
p/n: 10-0010-44
Cover, rear apron over fuel tank. 3-1/2 inch diameter hollow cup to cover hole above fuel gauge sending unit.
Fender Skirt Edge Weatherstrips
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Fenderskirt edge seal
p/n: 40-0279-44
Pad, wheel shield. Closely copied from original for perfect fit. Ten (10) foot strip, sufficient for one (1) car.Length: 120.0 inches. Height: .75 inches.
Fenderskirt edge seal
p/n: 60-0298-45
Seal, wheel streamliner (fenderskirt) to fender. Two (2) strips each cut five (5) foot long.Length: 60.0 inches. Width: .625 inches.
Fenderskirt edge seal
p/n: 25-0096-44
Sealing strip, fenderskirt to body. Two extruded rubber strips fifty one (51) inches long matching original profile.Length: 51.0 inches. Width: .375 inches.
Fender to Radiator Seal
p/n: 40-0066-44
This Fender to Radiator Seal is designed from original parts so it fits correctly. Sold as a eight and seven-sixteenths (8-7/16) inch pair.
Fenderskirt edge seal
p/n: 70-1281-44
Seal, fenderskirt edge. Exact original profile. Two strips four (4) feet long.
Fenderskirt edge seal
p/n: 70-1280-44
Seal, fenderskirt edge. Exact original profile. Two (2) strips four (4) feet long.Height: 1.0 inches.
Rumbleseat step pad
p/n: 40-0050-44
Pad, rumbleseat step, with "P" logo, fully detailed slipover pad for old core. Fits original trim ring.Height: .50 inches.
Fenderskirt edge seal
p/n: 70-0992-44
Sealing strip, fenderskirt edge to body. Two (2) strips seventy two (72) inches long.Length: 72.0 inches. Width: .75 inches. Height: .4375 inches.
Body / Cowl to Fender Seals
p/n: 70-2787-43
This Body / Cowl to Fender Seals pair is designed from the original part for superior fitment and function. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Front Fender Seals
p/n: 60-0522-45
Seal, front fender baffle, right and left. One (1) pair per car. Length: 5-1/4" inches.
Fenderskirt edge seal
p/n: 40-0476-44
Seal, fenderskirt edge. Two (2) strips of proper cross section forty two (42) inches long.Length: 42.0 inches. Width: .8125 inches.