Horn button contact cushion
p/n: 50-0409-21
Separator, horn contact. For standard or non-flexible wheel.
Cowl Vent Hose
p/n: 60-0457-54
Hose, cowl vent drain. Seems to be correct for some models rather than our #50-0259-54.
Horn Button Contact Set
p/n: 60-0492-21
This is a three (3) piece Horn Button Contact set which is designed from the original part for superior fitment and function. Renews the operation of the steering wheel horn blowing ring.
License Light Mounting Pad
p/n: 60-0074-17
Mounting pad, license light. Three and one eighth (3-1/8) inch by eight and seven eighths (8-7/8) inch. Fully detailed.Length: 8.875 inches.
Door Lower Weatherstrips
p/n: 20-1652-73
This three (3) piece Lower Door Weatherstrip set is designed from the original part for superior fitment and seal. Use full-length for front doors, cut third piece in half to complete installation for both rear doors.
License Lens Gasket
p/n: 70-2276-16
Gasket, license light lens. Fully molded with proper details.Length: 3.0 inches. Width: 1.6875 inches.
Brake and clutch shank seal
p/n: 70-0465-23
Grommets, brake and clutch pedal shank below floorboard.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Backup Light Mounting Pad
p/n: 60-0072-17
Mounting pads, back up lights, elliptic, sharp beaded edge. One and five sixteenths (1-5/16) inch by two and seven eighths (2-7/8) inch.Length: 2.
Steering gear bushing
p/n: 30-0340-36
Bushing, steering gear lever ball stud (Pitman arm). Originally made in one piece as spool bushing, but replacements made in halves.
Cowl vent weatherstrip
p/n: 70-0143-54
Gasket, cowl vent. Perfect copy of original, not a sponge substitute, top quality material.
Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Division bar chrome retainer
p/n: 70-3226-51
Retainer (rubber), outer windshield, stainless center post molding. Use with original stainless molding and clips.
Fabric Hood Lacing
p/n: 20-0354-42
This Fabric Hood Lacing installs where the hood rests on the cowl panel. Original woven style lacing complete with installation tacks. Sold as a forty-nine (49) inch strip.
Fuel Tank Filler Neck Grommet
p/n: 20-0345-39
This Fuel Tank Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Cowl Vent Gasket
p/n: 60-0081-54
Gasket, cowl vent. These parts are made of the highest quality and authenticity.Length: 15.0 inches.
Convertible Top Rest Bump Stop Block
p/n: 70-0397-67
This Convertible Top Rest Bump Stop Block pair is designed from the original part for an authentic fit, finish, and appearance. Attaches to the folding pillar arm of the convertible top assembly. This rubber only bumper block glues to the original metal core.
Antenna Wire Mount
p/n: 70-2263-19
Mount, radio antenna wire, under running board. Found on several models with factory type antennas that mount under the running board.
License Light Mounting Pad
p/n: 25-0045-17
Pad, rear license light body.Length: 7.0 inches. Width: 3.375 inches.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Taillight Gasket
p/n: 70-0900-15
Gasket, taillight housing. Also order #70-0471-15 for the taillight mounting pad, and for the taillight lens gasket order #70-0658-15. Length: 8.25 inches.
Antenna Mount Pad
p/n: 70-2621-21
Pad, roof mounted antenna gasket. Models with antenna mounted above center of windshield.
Hood to Cowl Weatherstrip
p/n: 60-0056-42
This Hood to Cowl Weatherstrip is extruded from a high quality dense rubber for a durable and proper seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Hood to Cowl Weatherstrip
p/n: 60-0090-42
This Hood to Cowl Weatherstrip is extruded from a high quality dense rubber for a durable and proper seal. This pair comes with pre-drilled holes for easy installation.
2-3/8" Firewall Grommet
p/n: 70-0185-20
This Firewall Grommet is used to run the main wiring harness in addition to five (5) accessory wires through the firewall. Designed from the original part for superior fit and seal.
Door Lock Weatherstrip
p/n: 50-0172-70
Weatherstrip, door lock, front and rear. Protects door lock mechanism from dust and weather.Length: 3.625 inches.
Trunk Weatherstrip
p/n: 60-0562-85
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts on the lower length of the trunk directly to the body.
Flexible Run Channel - 30 Inch Pair
p/n: 40-0309-57
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available in 30" pair.
Fender Welting
p/n: 20-1590-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Thirty (30) foot roll.
Gearshift Seal
p/n: 60-0471-24
This Gearshift Seal is designed from the original part for superior fitment and function. For the gearshift at floor.
Track Bar Bushing
p/n: 25-0080-32
Bushing, rear axle track bar. Made in halves for easier replacement. Sold in pairs, two (2) pair needed per bar.Height: .75 inches.
Center Division Bar Chrome Molding Retainer
p/n: 70-0373-51
Center Division Bar Chrome Molding Retainer for outside windshield center post stainless molding. Use with original stainless molding and clips. Length: 15-1/2 inches. Width: 1-1/4 inches.
Brown Starter Button Cover
p/n: 40-0419-89
Pad, starter button. Made with brown rubber like original.
Engine Mount
p/n: 20-1978-11
This Engine Mount is designed from the original part for superior fitment and function. This engine mount works to absorb and isolate engine and driveline vibrations. The set services one mount. 1937-1941 require four (4) sets for both Front and Rear. 1942-1948 require two (2) sets.
Rear Bumper Stone Deflector
p/n: 20-1569-29
This Rear Bumper Stone Deflector installs between the metal gravel deflector and the inside of the rear bumper. Made from top quality rubber to ensure durability and proper seal.
Running Board Mounting Pad
p/n: 20-1603-49
Grommets, running board to frame and front fender to cowl. Rubber grommets and metal washers. Twenty four (24) piece set.
Top Motor Grommet Set
p/n: 20-1637-67
This Top Motor Grommet Set contains three (3) pieces that are used for the top motor to the firewall bracket. Designed from the original part for superior fit and seal.
Gearshift Gasket
p/n: 60-0397-24
This sponge rubber Gearshift Gasket is one-half (1/2) inch thick. For the gearshift at floorboard. One required per vehicle.
Gravel Shield Bumper Set
p/n: 60-0146-30
This Gravel Shield Bumper Set is used as a rear bumper deflector. Also used between the radiator grille and the lower panel. Two (2) required per car. Designed from the original part for superior fitment and seal.
License Light Mounting Pad
p/n: 50-0034-17
Pad, rear license light and trunk handle body.Length: 7.50 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Exhaust System Hanger
p/n: 70-0626-13
Insulator (hanger) tailpipe to frame. See also our #70-0600-13.Length: 3.9375 inches. Width: 1.9375 inches.
Trunk Hinge Mounting Pad
p/n: 70-1231-87
Mounting pads, trunk hinge. Four (4) piece set.Length: 8.8125 inches.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Brown Gearshift Boot - Steering Column
p/n: 30-0069-89
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Brown rubber. Two and one quarter (2-1/4) inches long.
Trunk Weatherstrip
p/n: 20-1688-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Trunk Handle Mounting Pad
p/n: 50-0200-87
Mounting pad, trunk handle escutcheon.Length: 6.75 inches.
Bumper Seal
p/n: 70-0563-45
Filler valance or deflector, rear. Eight (8) inches long (cut shorter where required), three (3) to four (4) required per car.
Fuel Neck Grommet
p/n: 60-0049-41
Grommet, fuel filler neck with proper retaining flange. Oval style. Three and three fourths inch (3-3/4) outside width by four and one half inch (4-1/2") outside length by three fourths (3/4") inch height.
Accelerator Rod Seal
p/n: 40-0205-88
This Accelerator Rod Seal is used as an accelerator rod through the toeboard. Molded from a high-quality EPDM dense rubber.
Hood to Cowl Weatherstrip
p/n: 60-0138-42
This Hood To Cowl Weatherstrip pair installs at the rear of the engine bay to seal between the hood and vehicle body cowl. Sold as a pair for left and right side.
Handbrake Seal
p/n: 60-0396-24
Seal, handbrake at floorboard. Rubber sponge, one (1) required per vehicle.Length: 4.50 inches. Width: 2.0 inches. Height: 1.25 inches.
Convertible Weatherlip
p/n: 70-0616-67
Weather deflector, edge of folding top fabric near folding post, mounted on body.
Firewall Grommet
p/n: 40-0222-21
This Firewall Grommet is used to run the throttle cable and wiper vacuum line through the firewall as well as a drain hole for the cowl vent. The holes in the three (3) hole design measure: 9/16", 3/8", and 1/4".
2-1/2" Firewall Grommet
p/n: 30-0111-21
This Firewall Grommet is used to run the speedometer cable through the firewall. The grommet is retained by a steel collar, not included.
Taillight Lens Gasket
p/n: 60-0100-15
Gasket, taillight lens.Length: 5.125 inches. Width: 1.875 inches.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Door Weatherstrip
p/n: 20-0390-72
This Door Weatherstrip is the primary door to body weatherstrip. Includes enough to do front, top and backside of one door. Order two (2) for both doors.
Firewall Grommet
p/n: 40-0221-21
This Firewall Grommet is used to run the speedometer cable, oil tube, and the temperature tube through the firewall. The three (3) holes measure 5/16", 1/4", 3/16".
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Cowl Vent Gasket
p/n: 20-1613-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Manufactured to OEM specifications to install for an authentic fit and finish.
Front coil spring pad
p/n: 50-0358-35
Insulators, front coil spring. Fabric reinforced rubber as original.
Stabilizer Shaft Link Bushing
p/n: 60-0317-33
This Stabilizer Shaft Link Bushing works to support the vehicle front stabilizer or sway bar shaft. Six (6) required per vehicle.
Black Gearshift Boot - Steering Column
p/n: 30-0069-36
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Black rubber. Two and one quarter (2-1/4) inches long.
Brake and Clutch Pedal Bumpers
p/n: 60-0104-24
Bumpers, brake and clutch pedal shank, rides under floorboard. One and one eighth (1-1/8) inch clearance for pedal shaft. Compare with part 60-0579-24.
1-1/2" Firewall Grommet
p/n: 70-0186-20
This Firewall Grommet is used to run the vacuum operated radio antenna lines through the firewall. Designed from the original part for superior fit and seal.
Firewall Grommet
p/n: 40-0223-21
This Firewall Grommet can be used for a variety of applications since the grommet is plain (no holes). Designed from the original part for superior fit and seal.
Starter Pedal Pad
p/n: 25-0049-89
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Gearshift Boot - Brown
p/n: 20-2166-26
This Gearshift Boot is designed from the original part for superior fitment and seal. This boot fits over the gearshift tower to make a weathertight connection for the transmission gearshift rod as it passes up through the vehicle floorboard.
Hood Bumper Set
p/n: 20-1588-42
This twelve (12) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Quarter Window Vertical Leading Edge
p/n: 20-1656-76
This Quarter Window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment, finish and function. This part fits Ford convertible only and is the weatherstrip that holds the quarter window glass in the frame.
Door Handle Gasket
p/n: 70-2230-69
Gasket, outside door handle. Precision die cut from one thirty seconds (1/32) inch dense rubber to fit original factory handles.
Threaded Ends Insulator for Propeller Shaft and Exhaust Muffler
p/n: 70-0631-27
A steel core, double end threaded quality rubber Insulator that functions as an exhaust system muffler pipe bracket insulator. Also functions as a propeller shaft bearing to frame crossmember insulator.
2-1/4" Firewall Grommet
p/n: 50-0166-20
This Firewall Grommet is used to run the wiring harness through the firewall mat. Designed from the original part for superior fit and seal.
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
Door Check Link Rod End Stop
p/n: 70-0479-70
End nut, check link (rubber bar with steel bar insert). Three fourths (3/4) inch by three fourths (3/4) inch by two (2) inch threaded five sixteenths (5/16) inch. (For round stop nut, see our #70-0326-70).
Shock Absorber Arm Bushing
p/n: 30-0192-32
Bushing, shock absorber arm. Restore proper shock action.Height: 1.375 inches.
Steering column seal
p/n: 60-0478-36
Seal, steering column at toe board, for steering column housing and shifter control shaft jacket. Top quality sponge rubber, accurately cut.
Door Weatherstrip
p/n: 60-0047-73
Weatherstrip, lower door. Fastens to cab threshold. Two strips thirty six (36) inch long each.Length: 36.0 inches. Width: .4375 inches.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Hood Bumper Set
p/n: 20-0359-42
This ten (10) piece Hood Bumper set is designed from the original parts for superior fitment and function. Manufactured to OEM original standards.
Lower Door Weatherstrip Retainers
p/n: 20-0393-73
This Lower Door Weatherstrip Retainer pair is designed from the original part for superior fitment, finish and function. A pair of retainers for the lower door weatherstrips that mount on the left and right rocker sills. Does not include door weatherstrips.