Splash Apron / A-Arm Dust Shield
p/n: 70-2801-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Radiator Side Seals
p/n: 70-3990-31
This Radiator Side Seal pair is designed from the original part for superior fitment and function. Left and Right seals are die cut from quality masticated rubber to authentic original dimensions.
Rear Upper Engine Mount
p/n: 60-0463-11
This Rear Upper Engine Mount is designed from original part for correct fitment and function. Made of a high-quality EPDM dense rubber for durability and proper engine vibration isolation.
Steering Column To Floor Seal
p/n: 20-0674-36
This Steering Column To Floor Seal is designed from the original part for superior fitment and sealing. Seal part is die cut from quality rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Front Suspension Bumper
p/n: 20-0034-32
Bumper, front suspension upper arm. Three eighths (3/8) inch by three fourths (3/4) inch bolt, twenty four (24) threads.
Taillight Assembly Mounting Pads
p/n: 70-3777-15
This Taillight Assembly Mounting Pad pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the taillight assembly and the vehicle body.
Cowl Vent Gasket
p/n: 60-0601-54
Side cowl vent seal. One eighth (1/8) inch thick high quality sponge design.Length: 8.50 inches. Width: 5.375 inches.
Directional or Back Up Light Lens Gaskets
p/n: 70-3776-16
This Directional Turn Signal or Back Up Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Light Lens and the Light Housing or Bezel.
Body Mounting Pad
p/n: 70-2165-48
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. Used on the bottom of most mounting locations.
Decklid Top Cover Weatherstrip
p/n: 70-3922-67
This Decklid Top Cover Weatherstrip is designed from the original part for a superior fitment and seal. This seal mounts around the full perimeter of the soft top storage compartment.
Taillight Lens Gaskets
p/n: 70-3235-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between taillight lens & taillight housing.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Directional and Parking Light Lens Gaskets
p/n: 70-3115-16
This Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Door Handle Gasket Set
p/n: 50-0560-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do two (2) doors.
Hood to Cowl Weatherstrip
p/n: 70-3959-43
This Hood To Cowl Weatherstrip has the proper rubber cross section and made from top quality rubber to ensure durability. Designed from the original part for a superior fitment and seal.
Rear Bumper Trim Welts
p/n: 70-4092-45
This pair of Quarter Panel to Rear Bumper End Trim Welts are designed from the originals for superior fitment and seal. These welt strips mount to the rear quarter panel bumper end piece, with one per vehicle side.
Rear Seat Back Finish Panel to Package Tray Weatherstrip
p/n: 70-4096-87
This Rear Seat Back Finish Panel To Package Tray Weatherstrip mounts directly to the body to seal the Rear Seat Back Finish Panel to the Package Tray.
Window Stop Stem Bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Hood Bumper
p/n: 70-0770-42
Bumper, fender to hood. Correct detail with ridges as original. Four (4) required per car.Length: 1.3125 inches.
Window Regulator | Accelerator Rod Seal
p/n: 60-0652-70
This Window Regular | Accelerator Rod Seal is used as a front window regulator seal for 1955-60 passenger cars with electric windows and for 1957-62 Corvette models. Used as an accelerator rod through toeboard seal for 1955-62 V8 only Corvettes.
Glovebox Door Check Grommet
p/n: 27-0105-88
This Glovebox Door Check Grommet is manufactured out of 100% EPDM dense rubber for durability. Designed from original for a proper fit.