Flexible Run Channel - 30 Inch Pair
p/n: 40-0309-57
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available in 30" pair.
Trunk Handle Base Mounting Pad
p/n: 20-2385-86
This Trunk Handle Base Mounting Pad is designed from the original part for superior fitment, appearance and function. This correctly shaped with beaded edge mounting pad fits between the trunk handle base and the trunk compartment door.
Fender Welting
p/n: 20-1590-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Thirty (30) foot roll.
Gearshift Seal
p/n: 60-0471-24
This Gearshift Seal is designed from the original part for superior fitment and function. For the gearshift at floor.
2-7/16" Firewall Grommet
p/n: 70-0621-20
This Firewall Grommet is used to run the cowl vent drain hose and throttle control cable through the firewall. Designed from the original part for superior fit and seal.
2-7/16" Firewall Grommet
p/n: 70-0622-20
This Firewall Grommet is used to run the wiring harness, oil pressure tube, windshield wiper tube, capillary tube, and radio antenna wire through the firewall. Designed from the original part for superior fit and seal.
Exhaust System Hanger
p/n: 70-0600-13
Insulator, crosswise muffler hanger, two (2) per car. (See also our #70-0626-13).Length: 4.4375 inches. Width: 2.25 inches.
Brown Starter Button Cover
p/n: 40-0419-89
Pad, starter button. Made with brown rubber like original.
Engine Mount
p/n: 20-1978-11
This Engine Mount is designed from the original part for superior fitment and function. This engine mount works to absorb and isolate engine and driveline vibrations. The set services one mount. 1937-1941 require four (4) sets for both Front and Rear. 1942-1948 require two (2) sets.
Gearshift Gasket
p/n: 60-0397-24
This sponge rubber Gearshift Gasket is one-half (1/2) inch thick. For the gearshift at floorboard. One required per vehicle.
License Light Mounting Pad
p/n: 50-0034-17
Pad, rear license light and trunk handle body.Length: 7.50 inches.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Exhaust System Hanger
p/n: 70-0626-13
Insulator (hanger) tailpipe to frame. See also our #70-0600-13.Length: 3.9375 inches. Width: 1.9375 inches.
Trunk Hinge Mounting Pad
p/n: 70-1231-87
Mounting pads, trunk hinge. Four (4) piece set.Length: 8.8125 inches.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Brown Gearshift Boot - Steering Column
p/n: 30-0069-89
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Brown rubber. Two and one quarter (2-1/4) inches long.
Trunk Weatherstrip
p/n: 20-1688-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Hood Bumper Set
p/n: 20-0358-42
This fourteen (14) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Fuel Neck Grommet
p/n: 60-0049-41
Grommet, fuel filler neck with proper retaining flange. Oval style. Three and three fourths inch (3-3/4) outside width by four and one half inch (4-1/2") outside length by three fourths (3/4") inch height.
Front Vent Window Glass Edge Weatherstrips
p/n: 70-4896-56
This Front Vent Window Glass Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Felt (wooly napping strip) on extruded rubber with steel inserts that have original style mounting tabs or holes.
Accelerator Rod Seal
p/n: 40-0205-88
This Accelerator Rod Seal is used as an accelerator rod through the toeboard. Molded from a high-quality EPDM dense rubber.
Antenna Mount Pad
p/n: 70-2698-21
Pad, vacuum antenna mount, on fender.Width: 2.0625 inches. Height: 1.5 inches.
Handbrake Seal
p/n: 60-0396-24
Seal, handbrake at floorboard. Rubber sponge, one (1) required per vehicle.Length: 4.50 inches. Width: 2.0 inches. Height: 1.25 inches.
Brake and Clutch Shank Seal
p/n: 40-0016-24
Seal, brake and clutch pedal shank to floorboard (draft excluder).Length: 2.4375 inches. Width: 1.875 inches.
Firewall Grommet
p/n: 40-0222-21
This Firewall Grommet is used to run the throttle cable and wiper vacuum line through the firewall as well as a drain hole for the cowl vent. The holes in the three (3) hole design measure: 9/16", 3/8", and 1/4".
Firewall Grommet
p/n: 70-1203-20
This Firewall Grommet is used to run various electrical and dash gauge wires through the firewall. Also see our 32-1201-20 and 32-0225-20.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Door Weatherstrip
p/n: 20-0390-72
This Door Weatherstrip is the primary door to body weatherstrip. Includes enough to do front, top and backside of one door. Order two (2) for both doors.
Firewall Grommet
p/n: 40-0221-21
This Firewall Grommet is used to run the speedometer cable, oil tube, and the temperature tube through the firewall. The three (3) holes measure 5/16", 1/4", 3/16".
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Cowl Vent Gasket
p/n: 20-1613-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Manufactured to OEM specifications to install for an authentic fit and finish.
License Light Mounting Pad and Grommet Set
p/n: 60-0337-17
This License Light Mounting Pad and Grommet Set is designed from the original part for superior fitment and function. Mounting Pad for the license light to trunk lid. The Grommet is for the license bracket spacer post.
Brake and Clutch Pedal Pads
p/n: 20-2307-22
Brake and Clutch Pedal Pad pair. Molded on metal like original. Exact pyramid design. 1937-1940 Ford Trucks.
Front coil spring pad
p/n: 50-0358-35
Insulators, front coil spring. Fabric reinforced rubber as original.
Stabilizer Shaft Link Bushing
p/n: 60-0317-33
This Stabilizer Shaft Link Bushing works to support the vehicle front stabilizer or sway bar shaft. Six (6) required per vehicle.
Rear Spring Pad
p/n: 70-0245-32
Pad, rear spring insulator for two and one fourth (2-1/4) inch wide springs. (see our number 70-0191-32 for two (2) inch springs). Four (4) per vehicle.
Black Gearshift Boot - Steering Column
p/n: 30-0069-36
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Black rubber. Two and one quarter (2-1/4) inches long.
Brake and Clutch Pedal Bumpers
p/n: 60-0104-24
Bumpers, brake and clutch pedal shank, rides under floorboard. One and one eighth (1-1/8) inch clearance for pedal shaft. Compare with part 60-0579-24.
Firewall Grommet
p/n: 40-0223-21
This Firewall Grommet can be used for a variety of applications since the grommet is plain (no holes). Designed from the original part for superior fit and seal.
Spring shackle bushing
p/n: 30-0420-32
Bushing, spring shackle. Six (6) per car. Packard's "self flanging" type.
Starter Pedal Pad
p/n: 25-0049-89
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Gearshift Boot - Brown
p/n: 20-2166-26
This Gearshift Boot is designed from the original part for superior fitment and seal. This boot fits over the gearshift tower to make a weathertight connection for the transmission gearshift rod as it passes up through the vehicle floorboard.
Trunk Handle Grommet
p/n: 50-0183-87
Grommet, trunk handle bezel-thru-trunk lid. Special size, one (1) inch inside diameter.Buick 1937 Grommet, trunk handle bezel-thru-trunk lid.
Battery Carrier Edge Liner
p/n: 27-0091-21
Seal strip, battery to fender apron. Two (2) correct cross section strips nineteen (19) inches long.
Threaded Ends Insulator for Propeller Shaft and Exhaust Muffler
p/n: 70-0631-27
A steel core, double end threaded quality rubber Insulator that functions as an exhaust system muffler pipe bracket insulator. Also functions as a propeller shaft bearing to frame crossmember insulator.
2-1/4" Firewall Grommet
p/n: 50-0166-20
This Firewall Grommet is used to run the wiring harness through the firewall mat. Designed from the original part for superior fit and seal.
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
Door Check Link Rod End Stop
p/n: 70-0479-70
End nut, check link (rubber bar with steel bar insert). Three fourths (3/4) inch by three fourths (3/4) inch by two (2) inch threaded five sixteenths (5/16) inch. (For round stop nut, see our #70-0326-70).
License Light Mounting Pad
p/n: 40-0357-17
Pad, mounting, license light to body. A un-beaded pad as original with accurate outline and hole pattern.Length: 6.50 inches.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-2183-42
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part. This cowl lacing mounts with screws at the rear of the engine bay firewall directly to the body to seal between the hood and vehicle body cowl.
Door Weatherstrip
p/n: 60-0047-73
Weatherstrip, lower door. Fastens to cab threshold. Two strips thirty six (36) inch long each.Length: 36.0 inches. Width: .4375 inches.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Spare Tire Bumper
p/n: 70-0126-37
Rest pad, spare wheel cover, metal core, screw held type. Eight (8) required per car.Width: 1.75 inches. Height: 1.4375 inches.
Lower Door Weatherstrip Retainers
p/n: 20-0393-73
This Lower Door Weatherstrip Retainer pair is designed from the original part for superior fitment, finish and function. A pair of retainers for the lower door weatherstrips that mount on the left and right rocker sills. Does not include door weatherstrips.
Top Of Door Weatherstrips
p/n: 20-1646-73
This Top of Door Weatherstrip is designed from the original part for superior fitment, finish and function. One weatherstrip is enough for two doors. Cut to fit as needed for each upper door openings.
Firewall Grommet
p/n: 60-0010-45
This Firewall Grommet is the oblong four (4) hole style. The grommet fits the steel retainer for the throttle and choke cables, and the oil and temperature lines.
Top of Door Weatherstrips
p/n: 20-1645-73
This Top of Door Weatherstrip pair is designed from the original part for superior fitment, finish and function. The weatherstrip mounts on the vehicle body from approximately just above the door hinge to near the beltline on the lock side of the car.
Hood Rest Pad
p/n: 70-0150-42
Pad, hood rest, molded to brass core, screw mounted.Width: 1.75 inches.
Door Alignment Pad
p/n: 70-1821-71
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.