Front Engine Support
p/n: 70-0276-11
This Front Engine Support is designed from original parts for an exact reproduction. Constructed of rubber and steel for proper engine vibration isolation.
Front Fender Dust Shield Clip
p/n: 70-0681-44
This Front Fender Dust Shield Clip is designed from spring tempered wire, to original configuration. Up to sixteen (16) per car required.
Front or Rear Door Seals
p/n: 90-0130-72
Door edge weatherstrip. Two door seals. Used for the front doors on Chevrolet, Oldsmobile & Pontiac models. Also used for the front or rear doors on Buick models. If needing all four (4) door seals for Buick purchase two (2) pairs. This part is the primar
Front or Rear Door Weatherstrips
p/n: 90-0128-72
This Front or Rear Door Weatherstrip set is the primary weatherstrips for the door to the body. The set contains two (2) weatherstrips for either the front or the rear doors. Purchase two (2) sets if you need to complete all four (4) doors.
Front Spring Bumper
p/n: 70-0339-32
Bumper, front spring, upper arm on frame. Rubber with heavy steel core, including five sixteenths (5/16) inch stud.
Front Spring Bumpers
p/n: 30-0120-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. Self retaining type bumper manufactured with top quality materials.
Front Spring Bumpers
p/n: 60-0393-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. These axle to frame bottoming rebound pads are dense rubber blocks that mount to the front axle.
Front Spring Bumpers
p/n: 30-0087-32
This Front Spring Bumper pair is a quality reproduction of the original factory part. Self retaining type bumper manufactured with top quality materials.
Front Spring Bumpers - Lower Suspension Arms
p/n: 70-0172-32
This Front Spring Bumpers pair is designed from the original part for an authentic fit, finish, and appearance. These front spring bumpers install to the lower suspension arms. An original copy reproduction.
Front Spring Rubber Bumpers
p/n: 70-0329-32
This Front Spring Rubber Bumper Pair fits to the upper control arms on frame. Manufactured to OEM specifications to install for an authentic fit, finish and function.
Front Stabilizer Bushing
p/n: 50-0094-34
Bushings, front stabilizer shaft-to-frame or stabilizer shaft, front or rear. Fully molded rubber.
Front Stabilizer Bushing
p/n: 60-0088-34
This Front Stabilizer Bushing pair is fully molded from EPDM dense rubber to ensure durability. Used to connect the stabilizer bar to the vehicle frame. Two (2) required per car.
Front Stabilizer Bushing
p/n: 30-0123-33
Bushings, front stabilizer mounting bracket. Fully molded rubber.
Front Stablizer Bar End Link Kit
p/n: 70-0574-33
Kit, front stabilizer bar link assembly replacement. Twenty two (22) piece set for both sides of one (1) car. Hex head bolt. 3/8"-16nc x 8-7/8" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Front suspension bumper
p/n: 40-0356-32
Bumper, front suspension upper arm. Vulcanized into one piece as original with steel plate and stud.
Front Suspension Bumper
p/n: 60-0093-32
Bumper, front lower suspension arm. Attaches to front cross member by carrot retainer.Height: 2.0 inches.
Front Suspension Bumper
p/n: 30-0489-32
Bumper, front suspension (inside of coil spring). Made with three eighths (3/8) inch stud as original.
Front Suspension Bumper
p/n: 50-0125-32
Bumper, front suspension, lower arm.Width: 2.625 inches. Height: 2.5625 inches.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Front Suspension Rebound Pad
p/n: 50-0083-32
Rebound pad, front suspension, upper arm, on frame. Rubber body, steel core with five sixteenths (5/16) inch stud.
Front Vent Window Glass Edge Weatherstrips
p/n: 70-4896-56
This Front Vent Window Glass Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Felt (wooly napping strip) on extruded rubber with steel inserts that have original style mounting tabs or holes.
Front Vent Window Weatherstrips
p/n: 20-2346-55
These left and right Front Door Vent Window Weatherstrips are the main weatherstrips needed to replace the rubber on your front door vent windows. They are molded in the shape of the window and designed from original parts for superior fitment and seal.
Fuel Filler Neck Grommet
p/n: 60-0022-41
This Fuel Filler Neck Grommet is fully molded rubber and slightly angled. Three and eleven sixteenths inch (3-11/16") outside diameter by two and three sixteenths inch (2-3/16") top hole diameter by two and five eighths inch (2-5/8") bottom hole diameter.
Fuel Filler Neck Grommet
p/n: 60-0040-41
This Fuel Filler Neck Grommet is a fully molded rubber, grommet slightly angled with a retaining flange. Three and five sixteenths inch (3-5/16") outside width by three and one half inch (3-1/2") outside length by two and one eighth inch (2-1/8") inside hole diameter.
Fuel Neck Grommet
p/n: 60-0049-41
Grommet, fuel filler neck with proper retaining flange. Oval style. Three and three fourths inch (3-3/4) outside width by four and one half inch (4-1/2") outside length by three fourths (3/4") inch height.
Fuel Neck Grommet
p/n: 70-0091-39
Grommet, fuel filler neck. Saddle style. Three and three eighths inch (3-3/8") outside width by three and five eighths inch (3-5/8") outside length by two and one fourth inch (2-1/4") inside hole diameter by one and one fourth inch (1-1/4") height.
Fuel Neck Grommet
p/n: 20-2177-39
Grommet, fuel filler neck. Fully molded rubber with small retaining lip. Three and five eighths inch (3-5/8") outside diameter by two and nine sixteenths inch (2-9/16") inside hole diameter.
Fuel Neck Grommet
p/n: 10-0136-41
Grommet, fuel filler neck. Oblong, fully molded rubber. Three and one fourth inch (3-1/4") outside length by two and three sixteenth inch (2-3/16") inside diameter.
Fuel Neck Grommet
p/n: 40-0043-39
Grommet, fuel filler neck. Fully molded rubber with retaining flange. Three and five eighths inch (3-5/8") outside diameter by two and one eighth inch (2-1/8") inside diameter by one inch (1") height.
Fuel Neck Grommet
p/n: 70-0090-39
Grommet, fuel filler neck. Off center flange style. Fully molded rubber.
Fuel Neck Grommet
p/n: 18-0020-41
Grommet, fuel filler neck. Fully molded rubber with retaining flange.
Fuel Neck Grommet
p/n: 40-0286-39
Grommet, fuel filler neck. Fully molded rubber. Three and one fourth inch (3-1/4") outside diameter by two and one half inch (2-1/2") inside diameter by five eighths inch (5/8") height. Also see our #40-0043-39 sold separately.
Fuel Tank Support Pad
p/n: 30-0482-41
This Fuel Tank Support Pad is made of a high quality EPDM dense rubber. This cushion is used to help reduce noise. Available by the foot.
Gearshift Boot
p/n: 70-2126-24
Boot, transmission gear hand shift lever. Molded in pliable black rubber which may be painted if needed for restoration.
Gearshift Boot - Black
p/n: 20-0334-26
This reproduction Black Gearshift Boot is designed from the original part for an authentic fit, finish, and appearance.
Gearshift Boot - Brown
p/n: 20-2166-26
This Gearshift Boot is designed from the original part for superior fitment and seal. This boot fits over the gearshift tower to make a weathertight connection for the transmission gearshift rod as it passes up through the vehicle floorboard.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Gearshift Gasket
p/n: 60-0397-24
This sponge rubber Gearshift Gasket is one-half (1/2) inch thick. For the gearshift at floorboard. One required per vehicle.
Gearshift Knob
p/n: 20-0583-24
This black floor shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This reproduction part is a direct screw on replacement for that broken, aged-out original knob.
Gearshift Knob
p/n: 20-0331-26
This sand colored column shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This reproduction part is a direct push on replacement for that broken, aged-out original knob.
Gearshift Seal
p/n: 60-0471-24
This Gearshift Seal is designed from the original part for superior fitment and function. For the gearshift at floor.
Glovebox bumper
p/n: 20-2391-88
Bumpers, glovebox door.Ford Cars 1960 Bumpers, fuel tank door. All Galaxie models. Ford Truck 1935-47 Bumpers, glovebox door.
Glovebox Door Bumper
p/n: 40-0501-88
This Glovebox Door Bumper is fully molded and designed from the original part for superior fitment and seal. This bumper is made from high-quality EPDM dense rubber to provide excellent durability.
Glovebox Door Bumper Stops
p/n: 20-1698-88
Bumper stops for the glovebox door - lower. Rubber Coated Steel like original. This part prevents the glovebox door from opening too far, reduces paint-chipping.
Glovebox Link Bumper
p/n: 70-1459-88
Bumper, glovebox check link. Fits on glovebox door arm as needed.Length: .75 inches. Width: .3125 inches. Height: .4375 inches.
Gravel Shield
p/n: 27-0065-44
Stone shield, front fender. Molded left and right.Length: 12.125 inches.
Gravel shield
p/n: 70-0477-44
Gravel shield between body and rear fender, right and left, steel core.
Gravel Shield
p/n: 70-0093-45
Rear body deflector apron or valance. Original copy including fastening bolt holes. You locate exhaust hole where needed. Approximately fifty eight (58) inches long.
Handbrake Seal
p/n: 60-0396-24
Seal, handbrake at floorboard. Rubber sponge, one (1) required per vehicle.Length: 4.50 inches. Width: 2.0 inches. Height: 1.25 inches.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Headlight Mounting Pad
p/n: 30-0142-14
Gaskets, headlight body mounting to fender. Cut to exact size as original.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Headlight to fender gasket
p/n: 20-2295-14
Gasket, headlight bucket to fender. Cork. Two (2) required per vehicle.
Heel plate
p/n: 70-3608-88
Heel plate to protect driver's side floor carpet. Identical to original. Only for models with carpet.
Hinge seal
p/n: 70-0481-73
Filler, front door hinge pillar at dash, right and left. With metal core. Located at top front of front door, under door flange.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.