Swing-Out Windshield Weatherstrip
p/n: 40-0036-52
This Swing-Out Windshield Weatherstrip comes in an eleven (11') foot strip. The seal slides into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Windshield Division Bar Gasket
p/n: 70-0486-51
Weatherstrip. windshield divider post, outer, brass core. Acts as retainer for outer chrome. Similar to our #70-0159-51 but shorter, twelve (12) inch overall.
Fender Light Pad
p/n: 18-0008-16
Pad, fender light. Two and three eights (2-3/8) inches wide by eleven and one half (11-1/2) inches over all. Gradual tapered base as original.
Rear Bumper Grommet
p/n: 70-0144-29
Grommets, rear bumper (Some cars have this type, some have our #70-0164-29, sold separately. They are both interchangeable and original). Fully molded rubber.
Trunk Weatherstrip
p/n: 70-1128-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Coil wire sleeve
p/n: 14-0022-21
Sleeve, spark plug wires from distributor to wiring tube, rubber only.
Hood ventilator wedge pad
p/n: 70-0317-42
Wedge pads, hood side ventilators. Fourteen (14) piece set.
Accelerator Pedal Service
p/n: 25-0094-40
Accelerator pedal. Black rubber. For brown see our #25-0094-89. Revulcanization service only. Includes new rubber sockets at base and for pedal rod.
Transmission Mounting Pad
p/n: 50-0335-25
Transmission support pad, insulator blocks, upper and lower.
Lower Suspension Arm Dust Seal Set
p/n: 70-0865-32
This four (4) piece Lower Suspension Arm Dust Seal Set is fully molded of high-quality EPDM dense rubber for durability and proper fitment. These seals are used to protect your lower suspension arm bushings from dust and debris.
Hood Corner Pad
p/n: 30-0088-42
Pad, hood front corner. Metal core, retained by four (4) tabs.Length: 3.25 inches. Width: 1.25 inches.
Stabilizer Bushing
p/n: 30-0483-33
Bearings, stabilizer rear rod. Requires two (2) per car. Fully molded rubber.
Cadillac V-8 Pedal Pad
p/n: 70-0148-22
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Hood Corner Pad
p/n: 30-0010-42
Pads, hood rear corners. High quality rubber with metal core as original.Length: 3.4375 inches. Width: 1.875 inches.
Plug Wire Sleeve
p/n: 30-0204-21
Sleeve, plug wire tube to distributor cap. One (1) pair required per car.Height: .9375 inches.
Swing-Out Windshield Weatherstrip
p/n: 60-0481-50
This Swing-Out Windshield Weatherstrip is designed from the original part. The seal mounts into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Brown Accelerator Service
p/n: 27-0070-89
Accelerator pedal. Brown rubber. For black see our #27-0070-40. Revulcanization service only.
Door Bottom Weatherstrips
p/n: 40-0538-73
This Door Bottom Weatherstrip pair is designed from the original part for superior fitment and seal. Held to door by steel strip. Sponge type rubber as original. For four (4) door models.
Accelerator Pedal Service
p/n: 30-0400-41
Revulcanization Service Only for Black Rubber Accelerator Pedal Pad. Includes new ball sockets as original, with correctly detailed tread pattern.
Rigid Run Channel
p/n: 30-0180-57
Channel, rigid run, for vent window division bar. Chrome beaded edge, mohair lined steel channel to proper dimensions for window side of wing window frame.
Trunk Weatherstrip
p/n: 70-1129-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Stabilizer Bushing
p/n: 30-0484-33
Bearings, stabilizer front rod. Requires two (2) per car. Fully molded rubber.
Front Bumper Grommet
p/n: 40-0122-30
Grommets, front bumper. Hollow construction for good fit. Fully molded rubber.
Taillight Mounting Pad
p/n: 70-0316-15
Pads, taillight mounting, right and left, top grade workmanship and material.
Gearshift Seal
p/n: 30-0165-24
Seal, gearshift to floorboard.Length: 5.625 inches. Width: 4.875 inches.
Rear window division bar seal
p/n: 70-0246-82
Gasket set, back window divider post. Inner and outer, with mounting holes. Four (4) piece set.
Cowl Vent Weatherstrip
p/n: 10-0174-54
Gasket, cowl vent. Die cut from original factory drawing.Length: 20.0 inches.
Detachable Center Post Pad
p/n: 70-0279-67
Pads, for bottom of folding post or body, brass core as original, screw held.Length: 1.875 inches. Width: 1.0625 inches.
Rear Bumper Grommet
p/n: 30-0067-29
Grommets, rear bumper. Length: 4.3125 inches. Width: 2.6875 inches.
Spare wheel carrier grommet
p/n: 30-0334-37
Grommet, rear spare wheel carrier bracket. Two (2) per car. (Also order our #32-0355-37 separately).
Engine Mount Pad
p/n: 30-0331-11
This Engine Mount Pad pair is used as a support at the timing gear cover. One (1) pair required per car. Sold only in pairs.
Engine Mount Pad
p/n: 30-0238-11
This Engine Mount Pad pair is used as a support cushion at the timing gear cover. Correct design and rubber compound. Sold only in pairs. One (1) pair required per car.
Brake and Clutch Pedal Pads - Brown
p/n: 40-0121-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Brown rubber.
Front Bumper Grommet
p/n: 27-0004-28
Grommet, front or rear bumper. Hollow construction, perfect fit. Note: In 1935 this grommet is used on the front bumper. In 1937-1938: this bumper is used on the rear bumper.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Brown Brake and Clutch Floor Plate
p/n: 18-0014-89
This Brake and Clutch Floor Plate is designed from the original part for superior fitment and seal. Fully molded in quality Brown EPDM rubber. For Black rubber see our #18-0014-24.