Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Spark plug grommet
p/n: 70-1181-21
Grommet, spark plug and coil wire at distributor cap outlets. For seven (7mm) millimeter, later years.
Spark plug retaining ring
p/n: 30-0352-21
Retaining ring, spark plug wire. Two (2) per car.Chevrolet 1935-48 Retaining ring, spark plug wire. Two (2) per car. All models.
Spring Eye Bushing
p/n: 30-0372-32
Bushing, rear spring eye leaf and shackle. Nine sixteenths (9/16) inch inside diameter, one and three eighths (1-3/8) inch barrel.
Spring seat service
p/n: 60-0619-35
Seat, rear spring. Revulcanization service only. Send in complete casting with metal sleeve bushing.
Spring Shackle Bushing
p/n: 40-0183-32
Bushing, spring and shackle, front and rear leaf springs. Eight (8) or twelve (12) required per car.Length: 1.25 inches. Height: 1.25 inches.
Spring Shackle Bushing
p/n: 30-0344-32
Bushing, rear spring and shackle. One and one eighth (1-1/8) inch diameter with nine sixteenths (9/16) inch hole. One set contains twelve (12) pieces.
Spring shackle seal
p/n: 70-1125-33
Washer, front and rear spring shackle, seal for shackle pin. Constructed of neoprene.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Stabilizer Grommet
p/n: 30-0310-33
Grommet, front or rear stabilizer links, lower. Fully molded rubber.
Stabilizer Grommet
p/n: 30-0406-33
Pad, stabilizer link assembly, front, in upper end at link. Four (4) used per car. Fully molded rubber. One inch (1") outside diameter by three sixteenths inch (3/16") inside hole diameter by three fourths inch (3/4") height.
Stabilizer Grommet
p/n: 70-0221-33
Grommet, rear stabilizer bar (angular sway bar). Four (4) required per car. Fully molded rubber.
Stabilizer Shaft Link Bushing
p/n: 60-0317-33
This Stabilizer Shaft Link Bushing works to support the vehicle front stabilizer or sway bar shaft. Six (6) required per vehicle.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Starter Button Cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Starter Pedal Bellows
p/n: 60-0210-21
Bellows, starter pedal shaft to floorboard. Three eighths (3/8) inch top hole with three (3) inch height.Width: 2.875 inches. Height: 3.0 inches.
Starter Pedal Pad
p/n: 25-0049-89
Pad, starter pedal. Original pattern, brown rubber, exact copy.Height: .50 inches.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Steering Column Cushion
p/n: 60-0012-36
Grommet, steering column to cowl, for U-bolt clamp. Black rubber. For brown see our #60-0012-89.Height: 1.25 inches.
Steering Column Cushion
p/n: 40-0259-36
Pad, steering post bracket. One (1) per car. Cushions steering post clamp to instrument panel.Length: 3.50 inches.
Steering Column Cushion
p/n: 40-0422-36
Insulator set, steering housing to frame. Set includes both inner and outer pieces.Length: 4.125 inches.
Steering Column Finish Strip
p/n: 70-0199-88
Finish seal strip, steering column to dash pan panel, in tan rubber per original, close copy.Width: .3125 inches. Height: .3125 inches.
Steering Column Floorplate
p/n: 50-0565-36
Floorplate, steering column at floorboard. Black rubber. For brown (tan) see our #50-0565-89. Made with brass core.Length: 9.375 inches. Width: 5.25 inches.
Steering Column Floorplate
p/n: 20-1694-88
Seal, steering column tube. Installs on top of floor mat.
Steering Column Gearshift Vacuum Boot
p/n: 60-0555-24
This Steering Column Vacuum Cylinder Boot is designed from the original part for superior fitment, finish and function. An excellent duplicate of original.
Steering Column Grommet
p/n: 70-2523-36
This Steering Column Grommet is designed from the original part for superior fitment and sealing. Fits at the steering column to dash at floorboard. Fully molded with durable black rubber over a metal core.
Steering Column Grommet
p/n: 30-0048-36
Grommet, steering column to instrument panel. Brown rubber only, excellent copy.Length: 5.0 inches. Width: 3.0 inches.
Steering Column Grommet - Black
p/n: 60-0621-36
This black rubber Steering Column To Toe Board Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality rubber to authentic original dimensions.
Steering Column Grommet - Brown
p/n: 60-0621-89
This brown rubber Steering Column To Toe Board Grommet is designed from the original part for superior fitment and sealing. Part is molded from quality rubber to authentic original dimensions.
Steering Column Seal
p/n: 60-0419-36
Seal, steering column toe pan. One (1) required per car. Top quality sponge rubber, five eighths (5/8) inch thick.Width: 3.50 inches. Height: .625 inches.
Steering gear bushing
p/n: 40-0130-36
Bushing, insulator, for steering gear arm. Four (4) required per car.
Steering gear bushing
p/n: 30-0340-36
Bushing, steering gear lever ball stud (Pitman arm). Originally made in one piece as spool bushing, but replacements made in halves.
Steering Gear Pitman Arm Bushing
p/n: 60-0105-36
This Steering Gear Pitman Arm Bushing is designed from the original part for superior fitment and function. Fully molded with steel core.
Steering Knuckle Support Seal
p/n: 50-0525-36
Seal, steering knuckle support, upper or lower. Die cut one fourth (1/4) inch, four (4) used per car.Height: .25 inches.
Steering Knuckle Support Seal
p/n: 50-0199-35
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
Steering knuckle support seal
p/n: 60-0089-32
Seal, steering knuckle support, upper. Four (4) per car.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Suspension bushing
p/n: 30-0339-36
Bushing, insulator, front suspension lower support arm, inner. Four (4) piece set.
Suspension bushing
p/n: 30-0341-36
Bushing, insulator, upper support arm, outer above steering knuckle support. Four (4) piece set.