Bumper - LH Back Door
p/n: 60-0333-71
A rubber Left-Hand Back Door Bumper. Dovetail to be used with old casing.
Bumper Seal
p/n: 70-0563-45
Filler valance or deflector, rear. Eight (8) inches long (cut shorter where required), three (3) to four (4) required per car.
Carpet Heel Plate
p/n: 40-0190-88
Heel pad. Black rubber. For brown see our #40-0190-89. To protect driver's side floor carpet.
Center Division Bar Chrome Molding Retainer
p/n: 70-0373-51
Center Division Bar Chrome Molding Retainer for outside windshield center post stainless molding. Use with original stainless molding and clips. Length: 15-1/2 inches. Width: 1-1/4 inches.
Channel Filler Weatherstrip
p/n: 20-1633-62
Seal, door glass and stainless frame special. Top, bottom, and sides for one door.Width: .375 inches. Height: .625 inches.
Choke, Throttle and Starter Wiper Motor Grommet
p/n: 20-1561-20
This Choke, Throttle or Wiper Motor Grommet is designed from the original part for superior fitment and usage. A multi-purpose grommet, it fits into the vehicles firewall to provide a secure passthrough for the mechanical choke, throttle rod or wiper motor wiring.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Chrome Molding Washer
p/n: 60-0727-45
Washer, for attaching chrome moldings on body. Fits into metal cup retainer. Three fourths (3/4) inch diameter, use as required.
Clutch and Brake Pedal Arm Seals
p/n: 20-1564-23
This Clutch and Brake Pedal Arm Seal pair is designed from the original part for an authentic fit, finish, and appearance. For Clutch and Brake pedal arms to floorboard.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Clutch and Brake Pedal Bumpers
p/n: 60-0579-24
This Clutch and Brake Pedal Bumper is designed from the original part for superior fitment and function. This pedal to floorboard bumper is the longer type with one and three-eighths (1-3/8") inch clearance for the pedal shaft.
Clutch and Brake Pedal Bumpers
p/n: 60-0104-24
This Clutch and Brake Pedal Bumper is designed from the original part for superior fitment and function. Pedal shank rides under floorboard. One and one-eighth (1-1/8") inch clearance for pedal shaft.
Clutch and Brake Pedal Pads
p/n: 60-0068-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. An oval style perfect reproduction to replace worn or damaged original pedal pads.
Clutch and Brake Pedal Pads
p/n: 60-0218-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch and Brake Pedal Pads
p/n: 20-1563-22
This reproduction Clutch and Brake Pedal Pad pair screws to the pedal arms for a precise, factory fit. With authentic concentric circle design, pads are a perfect reproduction to replace worn original pedal pads.
Clutch and Brake Pedal Pads
p/n: 60-0242-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch and Brake Pedal Pads - BLACK
p/n: 25-0024-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Black rubber.
Clutch and Brake Pedal Pads - BROWN
p/n: 25-0024-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Brown rubber.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0054-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Clutch Equalizer Bushing and Seals
p/n: 70-2029-24
This Clutch Equalizer Bushing and Seal set is designed from the original part for superior fitment and operation. The set includes a metal sleeved rubber bushing and two (2) molded rubber seals for each end of equalizer shaft.
Clutch or Brake Pedal Pad - Black
p/n: 70-0176-22
This reproduction Clutch or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch or Brake Pedal Pad - Brown
p/n: 70-0176-89
This reproduction Clutch or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Coil spring insulator pad
p/n: 70-0801-32
Pad, coil spring insulator. Molded four (4) piece set for one (1) car.
Coil wire sleeve
p/n: 14-0022-21
Sleeve, spark plug wires from distributor to wiring tube, rubber only.
Control Arms Cross-Shaft Bushing Seal
p/n: 60-0094-32
This Control Arms Cross-Shaft Bushing Seal is designed from the original part for superior fitment and seal. Installs at upper and lower control arm cross shaft bushing, at inner end of control arm.
Convertible Post Bumper
p/n: 14-0019-67
Pad, convertible top folding post bottom, Brass core as original. Later type, perfect reproduction.
Convertible Roof Rail Weatherstrip
p/n: 20-1636-65
This Convertible Roof Rail Weatherstrip is designed from the original part for superior fitment and seal. This window channel seal fits between windshield posts and door. Also fits along the top irons. This part is one (1) each. Five (5) individual pieces are required for the complete top.
Convertible Roof Rail Weatherstrip
p/n: 70-0478-65
This Convertible Roof Rail Weatherstrip fits on the folding roof of the vehicle and seals the side window when the window is fully raised. Fully molded with metal core. Eight (8) piece kit.
Convertible Roof Rail Weatherstrips
p/n: 60-0132-65
This eight (8) piece Convertible Roof Rail Weatherstrip set is designed from the original part for superior fitment and seal. These weatherstrips fit on the folding roof of the vehicle and seal the side windows when the windows are fully raised.
Convertible Soft Top Folding Post Pads
p/n: 60-0455-67
This Convertible Soft Top Folding Post Pad pair is designed from the original part for an authentic fit, finish, and appearance. Parts fasten on the lower end with two (2) screws. Pads have a metal core.
Convertible Top Arm Pad
p/n: 50-0310-67
Pad, folding post, lower, on bottom of post, held by two (2) screws. Brass core, right and left hand.
Convertible Top Arm Pad
p/n: 70-1217-67
Pad, top folding post. Fastens on lower end of post with two (2) screws. Metal core, close copy.
Convertible Top Front Bow Weatherstrip
p/n: 70-0100-64
This Convertible Top Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This header seal installs directly to the windshield frame to seal between the soft top and the top of the windshield.
Convertible Top Rest Bump Stop Block
p/n: 70-0397-67
This Convertible Top Rest Bump Stop Block pair is designed from the original part for an authentic fit, finish, and appearance. Attaches to the folding pillar arm of the convertible top assembly. This rubber only bumper block glues to the original metal core.
Convertible Weatherlip
p/n: 70-0616-67
Weather deflector, edge of folding top fabric near folding post, mounted on body.
Cowl Firewall Grommet
p/n: 20-1560-20
This Cowl Firewall Grommet fits into the upper section of the firewall for the main wiring harness. Also used to run the dash wires on the firewall and through the firewall.
Cowl Lacing Rubber Seal
p/n: 20-1587-42
This Cowl Lacing Rubber Seal is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body to seal between the firewall and hood.
Cowl Vent Drain Hose
p/n: 60-0381-54
This Cowl Vent Drain Hose is designed from the original part for superior fitment and seal. Length: 7-1/4" inches.
Cowl Vent Gasket
p/n: 30-0262-54
Gasket, cowl vent. Labyrinth style as original.Length: 12.75 inches.
Cowl Vent Gasket
p/n: 20-1613-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Manufactured to OEM specifications to install for an authentic fit and finish.
Cowl Vent Gasket
p/n: 40-0271-54
Gasket, cowl vent. Fully molded to original cross-section and outline.Length: 18.0 inches.
Cowl Vent Gasket
p/n: 60-0124-54
Gasket, cowl vent. Original labyrinth style, not sponge.Length: 16.5 inches. Width: 4.0 inches.
Cowl Vent Hose
p/n: 60-0457-54
Hose, cowl vent drain. Seems to be correct for some models rather than our #50-0259-54.