Taillight Lens Gasket
p/n: 70-3524-15
Gasket, taillight lens. Fully molded rubber. Includes both right and left sides.
Taillight Lens Gasket
p/n: 70-2140-15
Gasket, trunk center medallion trunk stop lamp lens. Proper construction with accurate lips for good sealing.Length: 1.375 inches. Width: 4.0625 inches.
Taillight Lens Gaskets
p/n: 70-3770-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between taillight lens & taillight housing.
Taillight Mounting Pad
p/n: 27-0069-15
Pad, taillight mounting pad to body. Fully molded with original details. Length: 6.375 inches.
Taillight Mounting Pad
p/n: 50-0173-15
Pad, taillight mounting, right and left.Width: 10.5625 inches.
Taillight Mounting Pad
p/n: 70-0471-15
Pads, taillight body to fender, right and left. Also order #70-0658-15 for the taillight lens gasket, and for the taillight gasket order #70-0900-15.
Taillight Mounting Pad
p/n: 40-0392-15
Pad, brake light. Mounts on center of trunk lid.Length: 13.125 inches.
Taillight Mounting Pad
p/n: 60-0144-15
Pads, taillight body mounting, right and left.Length: 6.0 inches.
Taillight Mounting Pad
p/n: 30-0004-15
Pads, taillight mounting. Molded left and right with all details as original. Compare with our #30-0277-15.Length: 8.50 inches. Width: 3.75 inches.
Taillight Mounting Pad
p/n: 60-0008-15
Mounting pads, taillight. Length: 6.50 inches. Width: 2.6875 inches.
Taillight Mounting Pad
p/n: 50-0121-15
Mounting pads, taillights, right and left. Width: 10.5625 inches.
Taillight Mounting Pad
p/n: 70-1212-15
Pads, taillight mounting. Compound curved right and left hand custom molded pads. Also order the special design weatherproof gaskets for the lenses our #70-1213-15.
Taillight Mounting Pad
p/n: 30-0277-15
Gaskets, taillight to body. Molded left and right as original. Sold in complete sets only. Compare with our #30-0004-15.Length: 8.75 inches. Width: 3.
Threaded Ends Insulator for Propeller Shaft and Exhaust Muffler
p/n: 70-0631-27
A steel core, double end threaded quality rubber Insulator that functions as an exhaust system muffler pipe bracket insulator. Also functions as a propeller shaft bearing to frame crossmember insulator.
Tie rod dust cover
p/n: 10-0134-32
Rubber seal, tie rod ends and drag link ends. 2 or 4 required per car. Note: for 4 cylinder vehicles.
Tie Rod Dust Covers
p/n: 20-2484-36
This Tie Rod Dust Cover, drag link seal, is sold as a four (4) piece set. The seals are designed from originals for proper fitment.
Top Motor Grommet Set
p/n: 20-1637-67
This Top Motor Grommet Set contains three (3) pieces that are used for the top motor to the firewall bracket. Designed from the original part for superior fit and seal.
Top Of Door Weatherstrips
p/n: 20-1646-73
This Top of Door Weatherstrip is designed from the original part for superior fitment, finish and function. One weatherstrip is enough for two doors. Cut to fit as needed for each upper door openings.
Top of Door Weatherstrips
p/n: 20-1645-73
This Top of Door Weatherstrip pair is designed from the original part for superior fitment, finish and function. The weatherstrip mounts on the vehicle body from approximately just above the door hinge to near the beltline on the lock side of the car.
Track Bar Bushing
p/n: 25-0080-32
Bushing, rear axle track bar. Made in halves for easier replacement. Sold in pairs, two (2) pair needed per bar.Height: .75 inches.
Transmission Mount Service
p/n: 30-0316-24
Insulator assembly, transmission support. Revulcanization service only. Send in your old core for service.
Transmission Mount Service
p/n: 60-0407-25
Insulator (support), transmission mounting. Revulcanization service only.Length: 7.0625 inches.
Transmission Mount Service
p/n: 50-0315-25
Mounting pad, transmission (also called insulator or support pad). Revulcanization service only.Length: 5.0 inches. Width: 3.4375 inches.
Transmission Mount Service
p/n: 60-0647-24
Mount, transmission support. Revulcanization service only.
Transmission Support Mount - Revulcanization Service Only
p/n: 60-0530-25
Insulator - Plate Assembly - Guide for transmission support bracket. This Revulcanization Service Only is designed to restore your transmission mount to a like new original condition. Please call or email for more service details and ordering.
Trunk Bumper
p/n: 34-0399-87
Bumper, trunk opening on lid. Metal core, as original, screw held. Two (2) required per car.
Trunk Emblem Mounting Pad
p/n: 50-0114-17
Mounting pad, trunk ornament. Top quality material, finely detailed.Hole to hole this part measures 9.5 inches.Width: 13.875 inches.
Trunk handle bezel and grommet
p/n: 60-0526-87
Bezel and grommet, trunk handle and license light body.
Trunk Handle Mounting Pad
p/n: 50-0200-87
Mounting pad, trunk handle escutcheon.Length: 6.75 inches.
Trunk Hinge Mounting Pad
p/n: 70-1229-87
Mounting pad, trunk hinge. Four (4) piece set.Length: 7.625 inches.
Trunk Hinge Mounting Pad
p/n: 70-1231-87
Mounting pads, trunk hinge. Four (4) piece set.Length: 8.8125 inches.
Trunk or Hood Bumper
p/n: 34-0203-42
This Bumper is designed to be used for the trunk or hood. The bumper is molded with clearance for the screw.
Trunk stop lamp lens gasket
p/n: 70-3525-15
Gasket, trunk stop lamp lens. Used on the decklid center of the trunk. Fully molded rubber.
Trunk Weatherstrip
p/n: 70-1129-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Trunk Weatherstrip
p/n: 20-1688-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Trunk Weatherstrip
p/n: 20-1685-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.