Gravel Shield Bumper Set
p/n: 60-0146-30
This Gravel Shield Bumper Set is used as a rear bumper deflector. Also used between the radiator grille and the lower panel. Two (2) required per car. Designed from the original part for superior fitment and seal.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Exhaust System Hanger
p/n: 70-0626-13
Insulator (hanger) tailpipe to frame. See also our #70-0600-13.Length: 3.9375 inches. Width: 1.9375 inches.
Clutch and Brake Pedal Pads
p/n: 20-2450-22
This reproduction Clutch and Brake Pedal Pad pair slip over the full perimeter of the clutch and brake pedals for a precise, factory fit. Detailed and finished to match the original appearance.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Brown Gearshift Boot - Steering Column
p/n: 30-0069-89
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Brown rubber. Two and one quarter (2-1/4) inches long.
Emergency Brake Cable Grommet
p/n: 20-2438-20
This Emergency Brake Cable Grommet is used to run the emergency brake cable through the firewall. Designed from the original part for superior fit and seal.
Front Engine Mount
p/n: 20-2401-11
This Front Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation. Two (2) required per car.
Rear Engine Mount
p/n: 20-2400-11
This Rear Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Air ventilator seal
p/n: 20-2965-31
Seals, air vent damper. Must drill out spot welds to replace the cracked rubber. Includes screws to put back together.
Brake and clutch shank seal
p/n: 70-0466-23
Grommet, brake and clutch pedal shank above floorboard. Special offset pattern as original.
Clutch and Brake Pedal Pads
p/n: 60-0242-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Door Weatherstrip
p/n: 60-0313-73
Weatherstrip, door bottom. Retained by metal strip, black only. Each strip approximately thirty two and one half (32-1/2) inches long.
Hood to Cowl Weatherstrip
p/n: 60-0138-42
This Hood To Cowl Weatherstrip pair installs at the rear of the engine bay to seal between the hood and vehicle body cowl. Sold as a pair for left and right side.
Beltline Weatherstrip
p/n: 60-0287-58
Weatherstrip, door window at beltline, outer, (scraper type). Each strip approximately twenty six (26) inches to twenty seven (27) inches long.
Fuel Neck Grommet
p/n: 60-0271-41
Grommet, fuel filler neck. Oblong shaped molded rubber with retaining flange. Three and three fourths inch (3-3/4") outside length by three and five eighths inch (3-5/8") outside width.
Trunk handle mounting pad
p/n: 70-2025-86
Pad, trunk handle to trunk lid. Fully molded with proper retaining lip, two (2) piece set.
Fuel Neck Grommet
p/n: 60-0149-41
Grommet, fuel filler neck (1955-1st type). Oblong fully molded rubber with retaining flange. Three and seven eighths inch (3-7/8") outside width by five and one eight inch (5-1/8") outside length by one and one eighth inch (1-1/8") height.
Hood Rest Pad
p/n: 30-0092-42
Hood Rest Pad. Molded rubber with a steel core. Six (6) required per car. Length: 1.75 inches Width: 1.625 inches.
2-1/2" Firewall Grommet
p/n: 30-0111-21
This Firewall Grommet is used to run the speedometer cable through the firewall. The grommet is retained by a steel collar, not included.
Taillight Lens Gasket
p/n: 60-0175-15
Gasket, taillight lens.Length: 3.50 inches. Width: 2.25 inches.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Door Bumper
p/n: 60-0334-71
Bumper, back door check link above door. Dovetail base fits check arm.Length: 1.0 inches. Width: 1.0 inches. Height: .625 inches.
Firewall Grommet
p/n: 60-0565-20
This Firewall Grommet is used to run the top hydraulic lines, wiring harness, and speedometer cable through the firewall. Designed from the original part for superior fit, finish and appearance.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Cowl to Fender Seal
p/n: 20-0443-45
Seal, front fender to cowl. Soft pliable sponge rubber designed to accurately fill the gaps between the back side of the fender and cowl. May be supplied as single strip that customer will have to cut in order to facilitate installation.
Rear Window Gasket
p/n: 20-0479-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Front coil spring pad
p/n: 50-0358-35
Insulators, front coil spring. Fabric reinforced rubber as original.
Steering Column Connecting Rod Seal
p/n: 60-0400-36
Steering column steering connecting rod seal. Power steering models require one (1) per car. Non-power steering models require two (2) per car.
Brake and Clutch Pedal Pad
p/n: 60-0218-22
Pad, brake and clutch pedal. Length: 3.75 inches. Width: 2.375 inches.
Rear Spring Pad
p/n: 70-0245-32
Pad, rear spring insulator for two and one fourth (2-1/4) inch wide springs. (see our number 70-0191-32 for two (2) inch springs). Four (4) per vehicle.
Black Gearshift Boot - Steering Column
p/n: 30-0069-36
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Black rubber. Two and one quarter (2-1/4) inches long.
Brake and Clutch Pedal Bumper
p/n: 60-0579-24
Bumper, brake or clutch pedal to floorboard. Longer type with one and three eighths (1-3/8) inch clearance for pedal shaft.Length: 2.75 inches.
Brake and Clutch Pedal Bumpers
p/n: 60-0104-24
Bumpers, brake and clutch pedal shank, rides under floorboard. One and one eighth (1-1/8) inch clearance for pedal shaft. Compare with part 60-0579-24.
Gearshift Boot - Brown
p/n: 20-2166-26
This Gearshift Boot is designed from the original part for superior fitment and seal. This boot fits over the gearshift tower to make a weathertight connection for the transmission gearshift rod as it passes up through the vehicle floorboard.
Quarter Window Vertical Leading Edge
p/n: 20-1656-76
This Quarter Window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment, finish and function. This part fits Ford convertible only and is the weatherstrip that holds the quarter window glass in the frame.
Door Weatherstrips - Lower
p/n: 60-0078-73
This Lower Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Heavy type with original ribbing and retainer lip.
Threaded Ends Insulator for Propeller Shaft and Exhaust Muffler
p/n: 70-0631-27
A steel core, double end threaded quality rubber Insulator that functions as an exhaust system muffler pipe bracket insulator. Also functions as a propeller shaft bearing to frame crossmember insulator.
Power brake carpet grommet
p/n: 70-3147-24
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
Luggage Compartment Handle Pad
p/n: 20-2626-86
This Luggage Compartment (Trunk) Handle Pad is designed from the original part for superior fitment and seal. This pad fits between the compartment door and handle.
Wiper control grommet
p/n: 20-2527-53
Pads, windshield wiper pivot. Use when windshield washer is part of wiper pivot. Replaces factory #8M-17541-B.
Steering Column Seal
p/n: 60-0518-36
Seal, steering column and shift column toe pan. Five eighths (5/8) inch thick sponge rubber.Width: 4.875 inches. Height: .625 inches.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Brake and Clutch Pedal Pads
p/n: 70-3003-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A square style direct fit reproduction to replace worn original pedal pads. Manufactured in black rubber.
Lower Door Weatherstrip Retainers
p/n: 20-0393-73
This Lower Door Weatherstrip Retainer pair is designed from the original part for superior fitment, finish and function. A pair of retainers for the lower door weatherstrips that mount on the left and right rocker sills. Does not include door weatherstrips.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Brake and Clutch Pedal Pads
p/n: 20-2452-22
This Brake and Clutch Pedal Pad pair is made from high-quality EPDM rubber for a precise, factory like fit. Manufactured to OEM specifications to install for an authentic fit and finish.
Tailgate Lower Weatherstrip
p/n: 20-2623-85
This Tailgate Lower Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts on the bottom of the tailgate.
Trunk Weatherstrip
p/n: 20-2620-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts to the lip on the body surrounding the trunk opening.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Antenna Mount Pad
p/n: 70-0392-19
Mounting pad, vacuum operated fender mounted antenna with one and one half (1-1/2) inch base.
Hood Bumper Set
p/n: 33-0680-42
This eight (8) piece Hood Bumper set is designed from the original parts for superior fitment and function.
1-7/16" Firewall Grommet
p/n: 60-0276-45
This Firewall Grommet is used to run the throttle rod and tube, oil pressure gauge pipe, heat indicator tube, and choke rod through the firewall.
Body Mounting Pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar.
Vent Window Division Bar Weatherstrip
p/n: 70-1432-56
This Front Vent Window Division Bar Weatherstrip is designed from the original part for superior fitment and seal. A single 32" inch (approximate) length of original cross-section extruded rubber.
Taillight Mounting Pad
p/n: 50-0410-15
Pad, taillight to fender. Width: 7.25 inches. Height: 4.0 inches.
Door Handle Gasket Set
p/n: 50-0322-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Starter Button Cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Hood rest pad
p/n: 12-0008-42
Pad, hood rest, front, metal core with non-spring tabs, otherwise as original, six (6) per car.
Spring shackle bushing
p/n: 70-0444-32
Bushing, rear spring shackle, upper. Four (4) required per car.
Taillight Lens Gasket
p/n: 50-0411-15
Gasket, taillight lens. Die cut three sixteenths (3/16) inch sponge rubber as original.Width: 6.25 inches. Height: 3.25 inches.
Front Lower Engine Mount
p/n: 20-0502-11
This Front Lower Engine Mount is designed from original part for correct fitment and function. Molded dense rubber for durability and proper engine vibration isolation.
Rear Bumper Stone Deflector Seal
p/n: 20-2462-29
This Rear Bumper Stone Deflector Seal installs between the rear bumper and body filler splash panel. The seal is used to keep the rear pan from vibrating against the bumper brackets.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Hydraulic Pump Mounting Pad
p/n: 70-1610-67
Cushion mount, hydraulic pump.Width: .6875 inches. Height: 1.0 inches.
Hood Support Rod Top Cap
p/n: 40-0346-42
Pad, hood rest rod. For five sixteenths (5/16) inch diameter hood support rod. Also see our #40-0103-42.Length: 1.0 inches.
Hood Support Rod Top Cap
p/n: 40-0103-42
Top cap, hood support rod. For seven sixteenths (7/16) inch diameter rod. Also see our #40-0346-42.Length: 1.0 inches.
Hydraulic Pump Mounting Pad
p/n: 70-0986-62
Mounting bracket and pad, for hydraulic pump. Number used as required.Length: 1.75 inches. Width: .8125 inches.
Steering Column Floorplate
p/n: 20-1694-88
Seal, steering column tube. Installs on top of floor mat.
Body Mounting Pad
p/n: 40-0453-48
Insulator, body mounting. Fully molded rubber with locating collar. Use as required. Up to eight (8) are used per car.
Cowl Vent Gasket
p/n: 20-0462-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. This gasket works to seal the cowl vent when closed into the cowl body. Made from top quality rubber to ensure durability and proper seal.
Hood Bumper Set
p/n: 20-0446-42
This twelve (12) piece Hood Bumper set is designed from the original parts for superior fitment and function. This set fits F-Series Trucks.
Hood Bumper Set
p/n: 20-2501-42
This six (6) piece Hood Bumper set is designed from the original parts for superior fitment and function. <br />
Hood to Cowl Filler Seal
p/n: 20-2500-42
This Hood to Cowl Filler End Seal pair is designed from the original part for superior fitment and seal. Filler pieces are made from quality EPDM rubber to authentic original dimensions. These filler seals fit to the top outside corners on the left and right side of the hood to cowl.
Hood to Cowl Weatherstrip - Cowl Lacing
p/n: 20-2502-43
This Hood to Cowl Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. A reproduction dense rubber extrusion and special tack fasteners.