Side Window Leading Edge
p/n: 20-2604-80
Side window vertical leading edge weatherstrip. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised.
Side window leading edge
p/n: 40-0371-80
Side window vertical leading edge weatherstrip (1952-1st type) This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised. Molded authentic rubber construction with metal core, this part does not include t
Side Window Lift Limit Cap
p/n: 60-0071-62
Caps, side window lift limit. Rubber, snap-over type, three fourths (3/4) inch diameter by five sixteenths (5/16) inch thick.
Side Window Roller
p/n: 70-0117-62
This Side Window Roller, anti-rattle roller, is manufactured using EPDM dense rubber to replace the original perfectly. The roller fits both styles of brackets.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
Side Window Weatherstrip
p/n: 20-2557-62
Seal, special window-sweep. Station Wagons only: Rubber that goes between door glass and staples to wooden frame. Use on door and quarter windows.
Side Window Weatherstrip Deluxe Set
p/n: 20-0472-60
This Side Window Weatherstrip Deluxe Set is for both truck doors and includes the back edge of vent window seal installed, beltline weatherstrips, door glass runs with rivets and original-type vent bar channel with brackets riveted in place.
Side Window Weatherstrip Set
p/n: 90-3288-90
This six (6) piece Side Window Weatherstrip Set is designed for superior fitment and function. The set contains the flexible run channels and the window felt beltline weatherstrips needed for the side window glass. The set does two (2) front doors.
Side Window Weatherstrip Set
p/n: 70-4633-60
This Side Window Weatherstrip Set is for both truck doors and includes the window felt beltline weatherstrips, door glass runs and original-type vent division bar channels. This is a basic replacement set with no run channel clips or division bar brackets.
Side Window Weatherstrip Set
p/n: 20-2541-58
This ten (10) piece Side Window Weatherstrip Set is designed from the original part for superior fitment and function. The set contains stainless steel division bars and stainless steel bead window felts. The set does two (2) front doors.
Sliding Quarter Window Seal
p/n: 60-0398-78
Weatherstrip, sliding quarter window. Mounted vertically in body where leading edge of sliding window fits when closed. Right & left rubber only.
Sliding Quarter Window Seal
p/n: 70-2162-78
Weatherstrip, sliding quarter window. Vertically mounted in body where leading edge of sliding quarter window fits when closed.Length: 13.75 inches.
Sliding Quarter Window Weatherstrip
p/n: 70-0353-78
This Sliding Quarter Window Weatherstrip is used for side window inner and/or outer, front and/or rear doors. Available in a 6ft. lengths.
Solenoid Plunger Boot
p/n: 60-0567-21
Boot, solenoid plunger, starter switch at starter.Height: 1.625 inches.
Spark plug grommet
p/n: 70-1180-21
Grommet, spark plug & coil wire at distributor cap outlets. For nine (9mm) millimeter wire, earlier years.
Speedometer Cable Grommet
p/n: 20-2435-20
This Speedometer Cable Grommet is used to protect the cable when running it through the firewall. Designed from the original part for superior fit and seal.
Speedometer Housing Grommet
p/n: 20-0447-20
This Speedometer Housing Grommet is used where the cable runs through the floorboard. Also allows for the choke and throttle cable to go through the firewall.
Splash Apron
p/n: 20-2508-45
This Splash Apron is designed from the original part for superior fitment and seal. Seals the lower front splash pan to the bottom of the radiator.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3059-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Spring eye bushing
p/n: 10-0131-35
Bushing, spring eye, both eye leaf and shackle. Front and rear.Qty Required:20 Twelve (12) required per front, eight (8) required per rear.
Spring seat service
p/n: 60-0619-35
Seat, rear spring. Revulcanization service only. Send in complete casting with metal sleeve bushing.
Spring Shackle Bushing
p/n: 40-0183-32
Bushing, spring and shackle, front and rear leaf springs. Eight (8) or twelve (12) required per car.Length: 1.25 inches. Height: 1.25 inches.
Spring shackle bushing
p/n: 70-0444-32
Bushing, rear spring shackle, upper. Four (4) required per car.
Spring Shackle Bushing
p/n: 30-0344-32
Bushing, rear spring and shackle. One and one eighth (1-1/8) inch diameter with nine sixteenths (9/16) inch hole. One set contains twelve (12) pieces.
Spring Shackle Bushing Set
p/n: 20-2481-33
This Spring Shackle Bushing Set is for the front of the rear leaf spring. Two (2) kits required per car.
Spring Shackle or Shock Absorber Link Bushing
p/n: 20-1274-32
This Bushing is manufactured to OEM specifications to install for an authentic fit, finish and function. Used for front or rear leaf spring on Ford models. Used as a rubber, shock absorber link bushing on Chrysler models.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Stabilizer Bushing
p/n: 27-0085-34
Bushings, for stabilizer bracket. Fully molded rubber. Correct dimensions, not an aftermarket replacement.
Stabilizer Bushing
p/n: 70-0627-33
Bushings, stabilizer bar, front. Fully molded rubber. One and three fourths inch (1 3/4") length by one and one half inch (1 1/2") width by three fourths inch (3/4") inside hole diameter by one and five eighths inch (1 5/8") height.
Stabilizer Grommet
p/n: 30-0310-33
Grommet, front or rear stabilizer links, lower. Fully molded rubber.
Stabilizer Grommet
p/n: 70-0221-33
Grommet, rear stabilizer bar (angular sway bar). Four (4) required per car. Fully molded rubber.
Stabilizer Link or Shock Grommet
p/n: 70-0737-33
This Stabilizer Link or Shock Grommet is designed from the original part for superior fitment and usage. Fully molded rubber.
Standard rubber washer
p/n: 60-0726-45
Washer, for attaching moldings, emblems, and fender guards as required on body.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Starter Button Cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Starter Pedal Bellows
p/n: 60-0210-21
Bellows, starter pedal shaft to floorboard. Three eighths (3/8) inch top hole with three (3) inch height.Width: 2.875 inches. Height: 3.0 inches.
Starter Solenoid Cable Rubber Boot
p/n: 70-0704-21
This Starter Solenoid Cable Rubber Boot is designed from the original part for superior fitment and function. This boot covers and protects the battery cable at the starter solenoid connection.
Steel Sash Channel - Door Glass
p/n: 20-0473-58
This reproduction Steel Sash Channel is designed from the original part for superior fitment and function. This left or right door glass channel fits in the bottom of door for the glass to sit in.
Steering Column Connecting Rod Seal
p/n: 60-0400-36
Steering column steering connecting rod seal. Power steering models require one (1) per car. Non-power steering models require two (2) per car.
Steering Column Cushion
p/n: 20-0453-36
This Steering Column Cushion is the steering column bracket to dash pad. This cushion is used as a noise reducer.
Steering Column Cushion
p/n: 40-0422-36
Insulator set, steering housing to frame. Set includes both inner and outer pieces.Length: 4.125 inches.
Steering Column Floorplate
p/n: 20-0449-88
Seal, brake, clutch and steering column to floor. Column shift models. Installs under metal plate at floor.
Steering Column Floorplate
p/n: 20-2646-88
Seal, standard trans. steering post to floor. Installs under metal plate.
Steering Column Floorplate
p/n: 20-1694-88
Seal, steering column tube. Installs on top of floor mat.
Steering Column Floorplate
p/n: 20-0450-88
Seal, brake, clutch and steering column to floor. Floor shift models.
Steering Column Floorplate
p/n: 20-0451-88
Seal, steering column to floor mat. Column shift models. Installs on top of mat.
Steering Column Floorplate
p/n: 20-0452-88
Seal, steering column to floor mat. Floor shift models. Includes hold down clips.
Steering Column Floorplate Gasket
p/n: 60-0395-36
This Steering Column Floorplate Gasket is designed from the original part for superior fitment and seal. Cover (grommet), steering gear-to-toe board seal. Width: 5-13/16" inches. Height: 6" inches.
Steering Column Gasket
p/n: 70-2317-88
Insulator, steering column lower mounting frame gasket. Triangular shape with mounting holes and column tube clearance.
Steering Column Grommet
p/n: 70-2523-36
This Steering Column Grommet is designed from the original part for superior fitment and sealing. Fits at the steering column to dash at floorboard. Fully molded with durable black rubber over a metal core.
Steering Column Grommet
p/n: 40-0421-36
Grommet, steering column and transmission shift rod through firewall.Length: 4.375 inches.
Steering Column Grommet
p/n: 60-0436-32
Grommet, steering gear. Molded with metal core as original with all original features.Length: 4.375 inches.
Steering Column Grommet
p/n: 12-0012-36
Grommet, steering column and shifter at toe board, reproduced with all original details.
Steering Column Seal
p/n: 60-0518-36
Seal, steering column and shift column toe pan. Five eighths (5/8) inch thick sponge rubber.Width: 4.875 inches. Height: .625 inches.
Steering Column Seal
p/n: 60-0435-32
Seal, steering column at toe pan, sponge.Length: 5.375 inches. Height: .25 inches.
Steering Knuckle Support Seal
p/n: 50-0199-35
Seal, steering knuckle support, upper pivot pin. Four (4) required per car.Height: .5 inches.
Suspension Bumper - Front Lower Control Arm
p/n: 50-0092-32
This Suspension Bumper is designed from the original part for superior fitment and function. Bumper mounts to the front suspension lower control arm. Two (2) per car required.
Tail light lens gasket
p/n: 70-3721-15
Gasket, taillight lens, two (2) piece set. Circular gasket stretches over oval shaped lens. Replaces factory #410622.
Tailgate Lower Weatherstrip
p/n: 20-2623-85
This Tailgate Lower Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts on the bottom of the tailgate.
Tailgate Secondary Side Weatherstrip
p/n: 20-2624-85
This Tailgate Secondary Side Weatherstrip is designed from the original parts for superior fitment and seal. These seals mount on the side of the tailgate.
Tailgate Sides and Bottom Weatherstrips
p/n: 20-2621-85
These Tailgate Sides and Bottom Weatherstrips are designed from the original parts for superior fitment and seal. The seals mount on the side and bottom corners of the wagon tailgate.
Taillight and License Plate Bracket Mounting Pad
p/n: 60-0493-17
This reproduction Taillight and License Plate Bracket Mounting Pad is designed from the original part for an authentic fit, finish, and appearance.
Taillight Gasket Kit
p/n: 70-0927-15
Gasket set, taillight assembly. Four (4) piece set for lens and housing, right and left.
Taillight Lens Gasket
p/n: 20-1988-15
Gasket, taillight lens. Inner and outer seal. Enough for one taillight lens.
Taillight Lens Gasket
p/n: 20-0411-15
Gaskets, taillight lens. Cork.Ford Truck 1948-56 Gaskets, lens to housing. Ford Cars 1941 Gaskets, taillight lens.
Taillight Lens Gasket
p/n: 60-0175-15
Gasket, taillight lens.Length: 3.50 inches. Width: 2.25 inches.
Taillight Lens Gasket
p/n: 50-0411-15
Gasket, taillight lens. Die cut three sixteenths (3/16) inch sponge rubber as original.Width: 6.25 inches. Height: 3.25 inches.
Taillight Lens Gaskets
p/n: 70-3770-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between taillight lens & taillight housing.
Taillight Lens to Housing Gaskets
p/n: 20-2408-15
This Taillight Lens to Housing Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the taillight lens and the taillight housing.
Taillight Mounting Pad
p/n: 12-0007-15
Pad, taillight mounting, symmetrical for right and left, exact copy.
Taillight Mounting Pad
p/n: 27-0062-15
Pad, taillight to body mounting. Right and left molded as original with proper bead lip. Length: 4.50 inches.
Taillight Mounting Pad
p/n: 50-0410-15
Pad, taillight to fender. Width: 7.25 inches. Height: 4.0 inches.
Taillight Mounting Pad
p/n: 27-0068-15
Pad, taillight and license bracket mounting. Not listed in Master Parts Books, but we have seen this part on several original cars.
Taillight Mounting Pad
p/n: 60-0176-15
Pad, taillight body mounting. Three (3) inch by six and one half (6-1/2) inch overall. Proper lip design.Length: 6.50 inches. Width: 3.0 inches.
Taillight Mounting Pad
p/n: 30-0124-15
Pads, taillight mounting. Molded left and right, with proper lip form and perfect detail.Length: 10.9375 inches.
Taillight Mounting Pads
p/n: 20-2407-15
This Taillight Mounting Pad pair is designed from the original part for superior fitment and sealing. These reproduction gaskets fit between taillight frame housing and the body.
Taillight Wiring Boot and Hose
p/n: 50-0420-15
Boot and hose, taillight wiring. Four (4) piece set includes end covers.Width: 16.375 inches.