Body To Frame Mounting Pad Set
p/n: 20-1597-48
This fifteen (15) piece Body to Frame Mounting Pad set is designed from the original parts for superior fitment and function.
Body to Frame Webbing
p/n: 20-1599-48
This Body to Frame Webbing is designed from the original part for superior fitment and function. This webbing is used to shim the body to the frame. Also used as a noise reducer material. Webbing is two (2) inch wide, twenty-five (25) foot long roll.
Body To Frame Mounting Pad Set
p/n: 20-1596-48
This nineteen (19) piece Body to Frame Mounting Pad set is designed from the original parts for superior fitment and function. These frame pads are installed between the frame and the floor pans.
Swing-Out Windshield Weatherstrip
p/n: 40-0018-52
This Swing-Out Windshield Weatherstrip comes in an eleven (11) foot strip. The seal slides into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Headlight Mounting Pad
p/n: 30-0354-14
Gasket, headlight front assembly to fender. Between headlight bucket and the fender receiver hole. One (1) pair per car, sold only in pairs.
Rear Window Gasket Set
p/n: 20-0398-81
This Rear Window Gasket Set is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Engine Mount Pad
p/n: 70-2577-11
This Engine Mount Pad pair is used as a lower support cushion. Correct design and rubber compound. Sold as a pair.
Suspension bushing
p/n: 30-0339-36
Bushing, insulator, front suspension lower support arm, inner. Four (4) piece set.
Radiator Mounting Pad
p/n: 30-0309-31
Grommet, several usages. Radiator core cradle tie rod to frame or rear stabilizer pad to link to where the leaf springs are bolted. Fully molded rubber. 2nd type with chamfered edge. Comes as a (4) piece set.
Suspension bushing
p/n: 30-0335-36
Bushing, insulator, torque arm to frame at rear. Four (4) piece set.
Taillight Mounting Pad
p/n: 40-0177-15
Pads, taillight bracket mounting, right and left. Length: 9.375 inches.
Division Bar Grommet
p/n: 70-0483-62
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Front Suspension Rubber Bumper
p/n: 60-0103-32
Front Suspension Rubber Bumper for the front suspension lower control arm (attaches to lower arm spring mount). Steel core, with original size bolt. Width: 1.625 inches.
Fuel Neck Grommet
p/n: 10-0136-41
Grommet, fuel filler neck. Oblong, fully molded rubber. Three and one fourth inch (3-1/4") outside length by two and three sixteenth inch (2-3/16") inside diameter.
Hood Corner Pad
p/n: 40-0127-42
Pads, hood corners, brass core. Approximately 80 degree angle. Integral tabs for installing.Length: 1.50 inches.
Clutch or Brake Pedal Pad - Brown
p/n: 70-0176-89
This reproduction Clutch or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Front Stabilizer Bushing
p/n: 70-0193-33
Bushings, front stabilizer bar. Fully molded rubber. One and five eighths inch (1 5/8") length by one and seven sixteenths inch (1 7/16') width by three fourths inch (3/4") inside hole diameter by one and eleven sixteenths inch (1 11/16") height.
Fresh air gasket
p/n: 70-1768-31
Seal, fresh air adaptor door. Part of assembly #903964. For vehicles with accessory air control systems.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Clutch and Brake Pedal Pads - BROWN
p/n: 25-0024-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Brown rubber.
Brake and Clutch Pedal Pads - Black
p/n: 40-0121-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Black rubber. For Brown see our 40-0121-89.
Taillight Mounting Pad
p/n: 27-0069-15
Pad, taillight mounting pad to body. Fully molded with original details. Length: 6.375 inches.
Fuel Neck Grommet
p/n: 18-0020-41
Grommet, fuel filler neck. Fully molded rubber with retaining flange.
Rear Stabilizer Bushing
p/n: 50-0171-34
Bushings, rear stabilizer bar mounting. Fully molded rubber. One and one half inch (1 1/2") length by one and one fourth inch (1 1/4" outside diameter by nine sixteenths inch (9/16") inside hole diameter.
Front Stabilizer Bushing
p/n: 50-0170-34
Bushings, front stabilizer bar mounting. Fits original bracket. Fully molded rubber. One and five eighths inch (1 5/8") length by one and three eighths inch (1 3/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter.
Rear Gravel Deflector to Bumper Face Bar
p/n: 70-0462-45
This Rear Gravel Deflector to Bumper Face Bar staples to the gravel deflector. The seal is die cut from dense rubber. Sold as a six (6) foot strip.
Taillight Mounting Pad
p/n: 60-0008-15
Mounting pads, taillight. Length: 6.50 inches. Width: 2.6875 inches.
Front Stabilizer Bushing
p/n: 30-0363-33
Bearings or bushings, front stabilizer rod. One (1) pair used per vehicle. Fully molded rubber.
Door weatherstrip
p/n: 20-1644-73
Weatherstrips, open car door hinge. Door seals molded to fit hinge area.
Front Spring Rubber Bumpers
p/n: 70-0329-32
This Front Spring Rubber Bumper Pair fits to the upper control arms on frame. Manufactured to OEM specifications to install for an authentic fit, finish and function.
Clutch and Brake Pedal Pads
p/n: 60-0068-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. An oval style perfect reproduction to replace worn or damaged original pedal pads.
Accelerator Pedal Pad
p/n: 70-0208-40
Pad, accelerator pedal. Black rubber. For brown see our #70-0208-89. Made to slip over old metal core after removing old rubber. Length: 8.25 inches.
Clutch and Brake Pedal Pads - BLACK
p/n: 25-0024-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Black rubber.
Door Bumper
p/n: 34-0305-71
Bumper assembly, front door hinge, upper, stop. Two (2) per car, steel core as original.Height: .6875 inches.
Suspension bushing
p/n: 30-0341-36
Bushing, insulator, upper support arm, outer above steering knuckle support. Four (4) piece set.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Front Suspension Bumper
p/n: 60-0093-32
Bumper, front lower suspension arm. Attaches to front cross member by carrot retainer.Height: 2.0 inches.
Clutch Equalizer Bushing and Seals
p/n: 70-2029-24
This Clutch Equalizer Bushing and Seal set is designed from the original part for superior fitment and operation. The set includes a metal sleeved rubber bushing and two (2) molded rubber seals for each end of equalizer shaft.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Overload Spring Arm Bumpers
p/n: 70-2301-32
A reproduction Overload Spring Arm Bumper pair manufactured to OEM specifications. Fully molded quality rubber bumpers that installs in the truck's overload spring arms.
Flexible Run Channel - 60 Inch
p/n: 20-1619-58
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available 60" lengths.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Flexible Run Channel
p/n: 20-1146-58
This Flexible Run Channel helps to eliminate window rattle, provides a smooth sliding surface for glass movement, and works to protect the glass. Stainless steel beaded. Available in sixty (60) inch strips.
Rear Gravel Deflector to Bumper Seal
p/n: 60-0020-30
This Rear Gravel Deflector to Bumper Seal is made of a high quality EPDM dense rubber extrusion. Designed from the original part so it fits correctly. Sold as a six (6) foot strip.
Window Pinchweld Seal
p/n: 70-0096-52
This twelve (12) foot Window Pinchweld Seal is designed from the original part for superior fitment and function. The part is used to seal and retain an outer decorative reveal molding. Used with our 70-1192-52.
Front Stabilizer Bushing
p/n: 30-0123-33
Bushings, front stabilizer mounting bracket. Fully molded rubber.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Door Hinge Weatherstrips
p/n: 20-1643-73
This Door Hinge Weatherstrip pair is designed from the original parts for superior fitment and sealing. These door edge weatherstrips are molded specifically to fit the door hinge area of the vehicle.
Cowl Vent Gasket
p/n: 30-0050-54
Gasket, cowl vent. Perfect reproduction, high quality, original configuration, not a sponge substitute.Length: 14.0 inches. Width: 5.75 inches.
Fuel Neck Grommet
p/n: 40-0043-39
Grommet, fuel filler neck. Fully molded rubber with retaining flange. Three and five eighths inch (3-5/8") outside diameter by two and one eighth inch (2-1/8") inside diameter by one inch (1") height.
Cowl Vent Gasket
p/n: 40-0271-54
Gasket, cowl vent. Fully molded to original cross-section and outline.Length: 18.0 inches.
Rear Window Gasket
p/n: 20-1668-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends. It also has the slot to accommodate the outer edge's decorative molding.
Rear Window Gasket
p/n: 20-1660-81
This Rear Window Gasket mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Window Gasket
p/n: 20-0395-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Exterior Windshield Division Bar
p/n: 20-2341-51
This stainless steel Exterior Windshield Division Bar is designed from the original part for superior fitment, appearance and function.
Cowl Vent Gasket
p/n: 70-0194-54
Gasket, cowl vent. Original solid rubber configuration, not a sponge substitute.
Front Bow Weatherstrip
p/n: 60-0440-64
Weatherstrip, front bow to windshield, outer. Installs on convertible top. Approximately four (4) foot ten (10) inches long.
Firewall Grommet
p/n: 30-0070-21
This Firewall Grommet is used to run instrument board cables through the firewall. The oval type with masked hole for six (6) wires or cables is the necessary replacement for correct restoration.
Accelerator Pedal Service
p/n: 60-0701-40
Pedal, accelerator. Revulcanization service only. Excellent cover detailing with molded in rod ball socket as original.
Hood Corner Pad
p/n: 60-0118-42
Pad. hood corner, steel core as original, front and rear.Length: 1.5 inches.
Gearshift Boot - Black
p/n: 20-0334-26
This reproduction Black Gearshift Boot is designed from the original part for an authentic fit, finish, and appearance.
Parking Light Mounting Pad
p/n: 60-0007-17
Mounting pads, parking lights.Length: 4.25 inches. Width: 2.375 inches.
Front Door weatherstrip
p/n: 10-0115-73
Weatherstrip, door opening, special bulb seal with lip to fit original retainer. Approximately 46 inch strip.Width: .375 inches. Height: .625 inches.