Body To Frame Mounting Pad Set
p/n: 20-1597-48
This fifteen (15) piece Body to Frame Mounting Pad set is designed from the original parts for superior fitment and function.
Body To Frame Mounting Pad Set
p/n: 20-1596-48
This nineteen (19) piece Body to Frame Mounting Pad set is designed from the original parts for superior fitment and function. These frame pads are installed between the frame and the floor pans.
Body to Frame Webbing
p/n: 20-1599-48
This Body to Frame Webbing is designed from the original part for superior fitment and function. This webbing is used to shim the body to the frame. Also used as a noise reducer material. Webbing is two (2) inch wide, twenty-five (25) foot long roll.
Headlight Mounting Pad
p/n: 30-0354-14
Gasket, headlight front assembly to fender. Between headlight bucket and the fender receiver hole. One (1) pair per car, sold only in pairs.
Rear Window Gasket Set
p/n: 20-0398-81
This Rear Window Gasket Set is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Swing-Out Windshield Weatherstrip
p/n: 40-0018-52
This Swing-Out Windshield Weatherstrip comes in an eleven (11) foot strip. The seal slides into the track (channel) attached to the glass that goes all the way around the windshield and creates a seal when the glass is pressed against the body of the vehicle.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Engine Mount Pad
p/n: 70-2577-11
This Engine Mount Pad pair is used as a lower support cushion. Correct design and rubber compound. Sold as a pair.
Radiator Mounting Pad
p/n: 30-0309-31
Grommet, several usages. Radiator core cradle tie rod to frame or rear stabilizer pad to link to where the leaf springs are bolted. Fully molded rubber. 2nd type with chamfered edge. Comes as a (4) piece set.
Suspension bushing
p/n: 30-0339-36
Bushing, insulator, front suspension lower support arm, inner. Four (4) piece set.
Suspension bushing
p/n: 30-0335-36
Bushing, insulator, torque arm to frame at rear. Four (4) piece set.
Taillight Mounting Pad
p/n: 40-0177-15
Pads, taillight bracket mounting, right and left. Length: 9.375 inches.
Division Bar Grommet
p/n: 70-0483-62
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Front Suspension Rubber Bumper
p/n: 60-0103-32
Front Suspension Rubber Bumper for the front suspension lower control arm (attaches to lower arm spring mount). Steel core, with original size bolt. Width: 1.625 inches.
Fuel Neck Grommet
p/n: 10-0136-41
Grommet, fuel filler neck. Oblong, fully molded rubber. Three and one fourth inch (3-1/4") outside length by two and three sixteenth inch (2-3/16") inside diameter.
Clutch or Brake Pedal Pad - Brown
p/n: 70-0176-89
This reproduction Clutch or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Hood Corner Pad
p/n: 40-0127-42
Pads, hood corners, brass core. Approximately 80 degree angle. Integral tabs for installing.Length: 1.50 inches.
Front Stabilizer Bushing
p/n: 70-0193-33
Bushings, front stabilizer bar. Fully molded rubber. One and five eighths inch (1 5/8") length by one and seven sixteenths inch (1 7/16') width by three fourths inch (3/4") inside hole diameter by one and eleven sixteenths inch (1 11/16") height.
Fresh air gasket
p/n: 70-1768-31
Seal, fresh air adaptor door. Part of assembly #903964. For vehicles with accessory air control systems.
Brake and Clutch Pedal Pads - Black
p/n: 40-0121-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. An oval style perfect reproduction to replace worn original pedal pads. Manufactured in Black rubber. For Brown see our 40-0121-89.
Clutch and Brake Pedal Pads - BROWN
p/n: 25-0024-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Brown rubber.
Fuel Neck Grommet
p/n: 18-0020-41
Grommet, fuel filler neck. Fully molded rubber with retaining flange.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Taillight Mounting Pad
p/n: 27-0069-15
Pad, taillight mounting pad to body. Fully molded with original details. Length: 6.375 inches.
Front Stabilizer Bushing
p/n: 50-0170-34
Bushings, front stabilizer bar mounting. Fits original bracket. Fully molded rubber. One and five eighths inch (1 5/8") length by one and three eighths inch (1 3/8") outside diameter by eleven sixteenths inch (11/16") inside hole diameter.
Rear Gravel Deflector to Bumper Face Bar
p/n: 70-0462-45
This Rear Gravel Deflector to Bumper Face Bar staples to the gravel deflector. The seal is die cut from dense rubber. Sold as a six (6) foot strip.
Rear Stabilizer Bushing
p/n: 50-0171-34
Bushings, rear stabilizer bar mounting. Fully molded rubber. One and one half inch (1 1/2") length by one and one fourth inch (1 1/4" outside diameter by nine sixteenths inch (9/16") inside hole diameter.
Front Stabilizer Bushing
p/n: 30-0363-33
Bearings or bushings, front stabilizer rod. One (1) pair used per vehicle. Fully molded rubber.
Taillight Mounting Pad
p/n: 60-0008-15
Mounting pads, taillight. Length: 6.50 inches. Width: 2.6875 inches.
Clutch and Brake Pedal Pads
p/n: 60-0068-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. An oval style perfect reproduction to replace worn or damaged original pedal pads.
Door weatherstrip
p/n: 20-1644-73
Weatherstrips, open car door hinge. Door seals molded to fit hinge area.
Front Spring Rubber Bumpers
p/n: 70-0329-32
This Front Spring Rubber Bumper Pair fits to the upper control arms on frame. Manufactured to OEM specifications to install for an authentic fit, finish and function.
Accelerator Pedal Pad
p/n: 70-0208-40
Pad, accelerator pedal. Black rubber. For brown see our #70-0208-89. Made to slip over old metal core after removing old rubber. Length: 8.25 inches.
Clutch and Brake Pedal Pads - BLACK
p/n: 25-0024-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Black rubber.
Door Bumper
p/n: 34-0305-71
Bumper assembly, front door hinge, upper, stop. Two (2) per car, steel core as original.Height: .6875 inches.
Suspension bushing
p/n: 30-0341-36
Bushing, insulator, upper support arm, outer above steering knuckle support. Four (4) piece set.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Clutch Equalizer Bushing and Seals
p/n: 70-2029-24
This Clutch Equalizer Bushing and Seal set is designed from the original part for superior fitment and operation. The set includes a metal sleeved rubber bushing and two (2) molded rubber seals for each end of equalizer shaft.
Front Suspension Bumper
p/n: 60-0093-32
Bumper, front lower suspension arm. Attaches to front cross member by carrot retainer.Height: 2.0 inches.
Overload Spring Arm Bumpers
p/n: 70-2301-32
A reproduction Overload Spring Arm Bumper pair manufactured to OEM specifications. Fully molded quality rubber bumpers that installs in the truck's overload spring arms.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Flexible Run Channel - 60 Inch
p/n: 20-1619-58
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available 60" lengths.
Flexible Run Channel
p/n: 20-1146-58
This Flexible Run Channel helps to eliminate window rattle, provides a smooth sliding surface for glass movement, and works to protect the glass. Stainless steel beaded. Available in sixty (60) inch strips.