Clutch or Brake Pedal Pad - Brown
p/n: 70-0176-89
This reproduction Clutch or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Control arm bushing seal
p/n: 60-0094-32
Seal, upper and lower control arm cross shaft bushing, at inner end of arm.1939-48: Lower only, all pass. (exc.
Control Arm Bushing Seal
p/n: 60-0095-32
Seal, lower control arm pivot bolt bushing. Four (4) per car.Width: .1875 inches.
Convertible Post Bumper
p/n: 50-0208-67
Bumper, on folding top female hinge, for folding post, when top is retracted, right and left, brass core as original.
Convertible Roof Rail Weatherstrip
p/n: 40-0197-65
This Convertible Roof Rail Weatherstrip fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
Convertible Roof Rail Weatherstrip
p/n: 70-1277-65
This Convertible Roof Rail Weatherstrip fits on the folding roof of the vehicle and seals the side window when the window is fully raised. Correct profile of original. Sold in complete sets only.
Convertible Roof Rail Weatherstrip
p/n: 12-0017-73
Weatherstrip set, windshield corner post and roof rail to window, fits metal retainer. Four (4) piece set for both doors.
Convertible Roof Rail Weatherstrip
p/n: 70-0498-65
This eight (8) piece Convertible Roof Rail Weatherstrip fits on the folding roof of the vehicle and seals the side window when the window is fully raised. Fully molded with brass core.
Convertible Roof Rail Weatherstrip
p/n: 40-0417-65
This Convertible Roof Rail Weatherstrip fits on the folding roof of the vehicle and seals the side window when the window is fully raised. Extrusion only, for side rails and windshield pillars.
Convertible Roof Rail Weatherstrip
p/n: 60-0076-65
This Convertible Roof Rail Weatherstrip fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
Convertible Roof Rail Weatherstrip
p/n: 20-2580-65
This Convertible Roof Rail Weatherstrip fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
Convertible Top Arm Cover Cap
p/n: 70-0736-67
This four (4) piece Convertible Top Arm Cover Cap set is designed from the original part for superior fitment, finish and function. Installs on the folding pillar to side roof rail links. A perfect copy in original grey rubber. Four (4) piece set.Length: 1-3/4" inches.
Convertible Top Front Bow Weatherstrip
p/n: 30-0503-65
This Convertible Top Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This seal installs directly to the convertible top to seal between the soft top and the top of the windshield.
Convertible Top Rest Block
p/n: 60-0698-67
Pad, convertible top rest. Fully molded with metal core replacement.
Convertible Top Rest Block
p/n: 60-0415-67
Bumper, folding top rear bow (in top compartment). Two (2) required per car. Brass core as original.
Convertible Top Rest Bump Stop Block
p/n: 70-0397-67
This Convertible Top Rest Bump Stop Block pair is designed from the original part for an authentic fit, finish, and appearance. Attaches to the folding pillar arm of the convertible top assembly. This rubber only bumper block glues to the original metal core.
Cowl to Fender Seal
p/n: 20-0443-45
Seal, front fender to cowl. Soft pliable sponge rubber designed to accurately fill the gaps between the back side of the fender and cowl. May be supplied as single strip that customer will have to cut in order to facilitate installation.
Cowl Vent Gasket
p/n: 20-0462-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. This gasket works to seal the cowl vent when closed into the cowl body. Made from top quality rubber to ensure durability and proper seal.
Cowl Vent Gasket
p/n: 12-0011-54
Gasket, cowl vent, molded sponge rubber to original size and configuration.
Cowl Vent Gasket
p/n: 60-0124-54
Gasket, cowl vent. Original labyrinth style, not sponge.Length: 16.5 inches. Width: 4.0 inches.
Decklid Lock / Handle Mount Gasket
p/n: 30-0126-87
This Decklid Lock / Handle Mount Gasket is designed from the original part for superior fitment, finish and function. Length: 4 inches.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Division Bar Grommet
p/n: 70-0483-62
These Division Bar Grommets are fully molded for the rear door vent divider post (wind deflector). Four (4) piece set.
Division bar grommet
p/n: 70-3135-62
Grommet, rear door vent divider post. Upper and lower, right and left. 4 piece set.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Door Bumper
p/n: 60-0334-71
Bumper, back door check link above door. Dovetail base fits check arm.Length: 1.0 inches. Width: 1.0 inches. Height: .625 inches.
Door Bumper
p/n: 50-0203-41
This Door Bumper is used for the fuel filler door on the rear fender. Molded from top-quality EPDM rubber over a steel core for durability. These bumpers are screw retained.
Door Bumper
p/n: 70-0168-71
Bumper, door side. Square type held by four (4) screws, metal core as original.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Door Check Arm Bumper
p/n: 20-1639-70
This Door Check Arm Bumper is designed from the original part for superior fitment and function. This rubber with arm slot bumper mounts on the door check arm. Works to cushion the door swing.
Door Conduit
p/n: 70-0828-21
Conduit, hydraulic line & power window wire. Front doors only. 2 pieces cut nine and one half (9-1/2) inches.Length: 9.50 inches. Height: 1.50 inches.
Door Edge Weatherstrips
p/n: 60-0030-73
This Door Edge Weatherstrip pair is designed from the original part for superior fitment and sealing. These primary door weatherstrips mount directly to the vehicle body.
Door Garnish Molding Pad
p/n: 30-0435-71
Support, door garnish molding. Up to twenty (20) required per car.Width: .875 inches. Height: 1.0 inches.
Door Glass Run Channel Set
p/n: 20-2537-58
Door Glass Run Channel Set - Includes front door side window division bar, run channel, and window felts. Fabric covered division bar and stainless steel window felts. This set does two (2) doors.
Door handle gasket
p/n: 20-2584-69
Pads, outside door handle. Set includes four (4) pieces for two (2) handles.
Door handle gasket
p/n: 20-2587-69
Pads, outside door handle. Enough for two (2) handles. Four (4) piece set.
Door Handle Gasket Set
p/n: 60-0673-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Door Handle Gasket Set
p/n: 50-0322-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Door Handle Gasket Set
p/n: 70-0572-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do two (2) doors.
Door Handle Gaskets
p/n: 20-0478-69
This two (2) piece Outside Door Handle Gasket pair is designed from the original part for superior fitment and seal. Gaskets have a proper raised edge to center the handle on so it fits correctly.
Door Handle Mounting Pad
p/n: 20-0577-86
Outside Door Handle Mounting Pad - Designed from an original part so it fits correctly.
Door Jamb Bumper
p/n: 20-2109-71
This Door Jamb Bumper is a quality reproduction of the original factory part. This rubber bumper mounts into a slot in the door jamb to cushion the door closure. Two (2) required per door.
Door Lock Bumper
p/n: 34-0484-71
This Door Lock Bumper is made from high-quality EPDM dense rubber to provide excellent durability. Designed for applications such as the upper door lock post.