Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Front Spring Bumper
p/n: 50-0423-35
Bumper, front spring. Fits onto original bracket.Length: 2..125 inches. Width: 2.0 inches. Height: 1.875 inches.
Rumble Seat Step Pad
p/n: 40-0050-44
Pad, rumble seat step, with "P" logo, fully detailed slipover pad for old core. Fits original trim ring.Height: .50 inches.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Accelerator Pedal Pad
p/n: 10-0001-40
Pad, accelerator pedal. Cements and fastens with screws to original metal pedal. Length: 6.50 inches.
Transmission Mounting Pad
p/n: 11-0025-25
Mount, transmission. Original pattern, superior workmanship.
Side Mount Cover Pad
p/n: 40-0314-37
Anti-rattle, spare wheel cover in fenderwell.Width: .25 inches.
Steering Column Grommet
p/n: 40-0007-36
Grommet, steering column at floor. One and one half (1-1/2) inch tube.
Parking Light Mounting Pad
p/n: 30-0282-17
Gaskets, parking light (fender light).Length: 2.75 inches. Width: 1.75 inches.
Firewall Pass Through Grommet
p/n: 40-0522-21
This Firewall Pass Through Grommet is the rectangular large type. Designed from the original part for superior fit and seal.
Coil wire sleeve
p/n: 70-0109-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
Gearshift Boot
p/n: 40-0076-88
Dust boot, gearshift, beehive type. Excellent copy and material. Used on some shift ball sockets.Length: 4.75 inches.
Hood Bumper
p/n: 40-0354-42
Bumper, fender to hood. Two (2) per car. Held by four (4) rivets.Length: 2.9375 inches.
Fuel Neck Grommet
p/n: 40-0067-39
Grommet, fuel filler neck. Oblong, fully molded rubber. Four and one eighth inch (4-1/8") outside length by two and one fourth inch (2-1/4") inside diameter.
Taillight Gasket
p/n: 70-0258-15
Gaskets, taillight mounting under fender wire conduit base. Width: 3.25 inches.
Rumble Seat Step Mounting Pad
p/n: 70-0262-45
Pad, rumble seat step plate mounting, rectangle type for top of fender.Length: 4.875 inches. Width: 4.25 inches.
Headlight Stanchion Pad
p/n: 70-0255-21
Mounting pads, horn and headlight stanchion base to hood latch shelf. Two and one half (2-1/2) inches by four and one fourth (4-1/4) inches.Length: 4.
Rumble Seat Step Pad
p/n: 60-0126-45
Pad, rumble seat step, on rear bumper bracket or fender. Rubber cover only, full slip-over type with bowtie emblem.
Side Mount Clamp Cushion
p/n: 40-0138-37
Cushion, sidemount clamp. Two and one eighth (2-1/8) inch by four and five eighths (4-5/8) inch.Length: 4.625 inches. Width: 2.125 inches.
Engine Mount Pad
p/n: 11-0026-11
This Engine Mount Pad is designed to original pattern with superior workmanship. Made from high-quality EPDM rubber for a precise, factory like fit. Two (2) required per car.