Headlight grommet
p/n: 25-0039-14
Base, headlight wire conduit and support post. (Vertical post under headlight).
Transmission Mounting Pad
p/n: 11-0025-25
Mount, transmission. Original pattern, superior workmanship.
Accelerator Pedal Pad
p/n: 10-0001-40
Pad, accelerator pedal. Cements and fastens with screws to original metal pedal. Length: 6.50 inches.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Rumble Seat Step Pad
p/n: 40-0050-44
Pad, rumble seat step, with "P" logo, fully detailed slipover pad for old core. Fits original trim ring.Height: .50 inches.
Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Hood Corner Pad
p/n: 40-0128-42
Pads, hood corners. Square type, brass core. Integral installation tabs. 90 degree angle, used on front or rear corners, as required.
Fuel Neck Grommet
p/n: 30-0232-41
Grommet, fuel filler neck. 2-1/2" inside diameter. Fits 3-3/8" hole in sheet metal. Overall width 4-1/8".
Fuel Neck Grommet
p/n: 30-0099-41
Grommet, fuel filler neck. Three and one half (3-7/16) inch inside diameter for four (4) inch hole in apron.
Rear Window Gasket
p/n: 70-0018-83
This Rear Window Gasket comes in a seven foot, three inch (7' 3") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Access Hole Plug
p/n: 10-0010-44
Cover, rear apron over fuel tank. 3-1/2 inch diameter hollow cup to cover hole above fuel gauge sending unit.
Brake and Clutch Pedal Pads
p/n: 40-0213-22
Pad, brake and clutch pedals. Horizontal oval style, slip over type.Length: 3.8125 inches. Width: 2.375 inches.
Steering Column Floorplate
p/n: 17-0001-36
Grommet, steering column floor, black rubber only, excellent copy of original.Length: 5.0 inches.
Windshield Gasket
p/n: 70-0078-52
This Windshield Gasket is made of a high-quality EPDM dense rubber extrusion. This four (4) foot weatherstrip mounts on the lower windshield.
Brake and Clutch Pedal Pads
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Rear Spring Bumper
p/n: 60-0137-32
Bumper, rear spring. Fits original retainer.Width: 2.5625 inches.
Axle Rebound Pad
p/n: 50-0254-35
Bumpers, front axle, springs to frame. Fit original retainers.Length: 1.9375 inches. Width: 1.8125 inches.
Windshield stanchion base pad
p/n: 10-0148-52
Pad, windshield stanchion mounting. Molded left and right. Varsity Roadster only.
Rumble Seat Step Pad
p/n: 40-0209-44
Pad, rumble seat step slip over style for original core, "DB" logo.
Rumble Seat Step Pad
p/n: 40-0353-44
Pad, rumble seat step, with "DS" logo. Fits old bracket and bezel. See our #40-0055-44 also.Height: .50 inches.
Red Brake and Clutch Pedal Pad
p/n: 30-0188-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0188-22.Length: 3.875 inches. Width: 2.875 inches.
Rumble Seat Weatherstrip
p/n: 70-0166-85
This Rumble Seat Weatherstrip is designed from the original part for superior fitment and seal. The strip seals the lower edge of the rumbleseat.
Radiator Brace Filler Strip
p/n: 70-0020-31
Filler strip, radiator brace rods. Retains ignition wire and thermometer tube in hollow brace rods. Thirty (30) inch strips.
Sidemount Wheel Carrier Grommet
p/n: 60-0002-37
This Sidemount Wheel Carrier Grommet for the wheel carrier brace support-at-cowl panel. Manufactured with a heavy brass core. Has a flexible neck. A close copy of original.
Fender Welting with 3/16" Bead - 50ft
p/n: 70-1100-44
A superior quality Fender Welting material constructed of reinforced black vinyl over a vinyl core. Typically used for attaching four (4) fenders to body. Sold in a 50 foot roll.
Fender Welting 1/4" Bead - 50ft
p/n: 70-1098-44
Welting, fender. Superior quality, proper construction of reinforced black vinyl over vinyl core, one and three eighths (1-3/8) inch wide. One fourth (1/4) inch bead, fifty (50) foot roll. Typically used to attach four (4) fenders to body.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Rumble Seat Step Pad
p/n: 40-0012-44
Pad, rumble seat step bears Chrysler medallion logo in center.Height: .50 inches.
Front Spring Bumper
p/n: 50-0238-35
Bumpers, front spring, Two (2) per car.Width: 2.0 inches. Height: 1.75 inches.
LaSalle Monogram
p/n: 70-0056-49
LaSalle monograms for center of running board matting, exact copy, to be in-laid.
Cadillac V-8 Pedal Pad
p/n: 70-0148-22
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Rumble Seat Step Pad
p/n: 40-0124-44
Pad, rumble seat step, with "Dodge" logo, slip over type to fit old steel core. Perfect detail and lettering.Height: .50 inches.
Firewall Grommet Set
p/n: 70-1147-21
This Firewall Grommet Set contains six (6) pieces intended for spark and choke rods, fuel line, oil gauge line and radiator brace rods. Designed from the original part for superior fit and seal.
Side Mount Spare Grommet Set
p/n: 70-1136-37
This six (6) piece Side Mount Spare Grommet Set is made from top-quality EPDM rubber and designed from the original parts for durability and proper function. This set can be used for various applications to support arms, brace rods, and cowl standoff posts.
Front Bumper Grommet
p/n: 70-0103-28
Grommets, front bumper. Theses are for the round, tubular bumper support.
Windshield Stanchion Base Pad
p/n: 40-0079-52
Pads, windshield stanchion mounting. Perfect copy, including concave bottom face to properly fit cowl, right and left.Length: 3.125 inches.
Hood Ventilator Bumper Set
p/n: 70-0011-42
This forty (40) piece Hood Ventilator Bumper set is designed from the original parts for superior fitment and function. The set includes bumpers and rivets for one (1) hood.
Firewall Grommet Set
p/n: 70-1149-21
This Firewall Grommet Set contains six (6) pieces that are intended for spark and choke rods, fuel line, oil gauge line and radiator brace rods. Designed from the original part for superior fit and seal.
Engine Mount Pad
p/n: 70-1162-11
This Front Engine Mount Pad pair is designed for cars with round cone type front engines. For V-12 and V-16 models.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Front Bow Weatherstrip
p/n: 30-0066-67
Pad, folding top, front frame to windshield. Five sixteenths (5/16) inch by one half (1/2) inch rectangular section, fifty (50) inches long. Length: 50.
Convertible Top Arm Pad
p/n: 30-0065-67
Pads, folding top swinging arms, right and left, dovetail cross section.
Axle Rebound Pad
p/n: 10-0002-35
Pad, front axle rebound, including bolt hole. Excellent copy, highest grade material.Width: 2.25 inches. Height: 1.50 inches.
LaSalle monogram pedal pad
p/n: 70-0037-22
LaSalle pedal pads, clutch and brake, excellent copy from authentic original with LaSalle monogram.
Side Mount Spare Grommet Set
p/n: 70-1134-37
This Side Mount Spare Grommet Set is made from top-quality EPDM rubber and designed from the original parts for durability and proper function. This set can be used for various applications to support arms, brace rods, and cowl standoff posts.
Axle Rebound Pad Service
p/n: 10-0003-35
Pad, rear axle rebound, perfect duplication. Length: 4.0 inches. Height: 1.25 inches.
Axle Rebound Pad
p/n: 30-0043-32
Pads, front axle rebound. Correct shape and design like original.Length: 3.625 inches. Width: 2.125 inches. Height: 2.125 inches.
Vacuum Brake Cylinder Rod Boot
p/n: 70-0010-24
This Vacuum Brake Cylinder Rod Boot is designed from the original part for superior fitment and seal. Made from durable rubber to original configuration.
Body Mounting Pad
p/n: 70-0298-48
Pads, body mounting for front bracket, right and left. Three eighths (3/8) inch by two and three fourths (2-3/4) inch by four (4) inches with two (2) collars and retaining rings. Two (2) required per car.
Firewall Grommet
p/n: 17-0045-20
This Firewall Grommet is designed as a firewall pass through for eight (8) wires or cables. For twelve (12) cylinder models only. For eight (8) cylinder models see our 17-0044-20.
Axle Rebound Pad
p/n: 30-0054-32
Pads, rear axle rebound.Length: 5.125 inches. Width: 1.4375 inches.
Front Apron Crossbar Grommet
p/n: 70-1130-45
Grommets, front splash apron crossbar.Width: 3.5 inches. Height: 3.6875 inches.
Steering Column Grommet
p/n: 30-0046-36
Steering column to toe board grommet. Made with a brass core, like original. For one and one half (1-1/2) inch steering column tube.
Front Apron Crossbar Grommets
p/n: 70-1131-45
This Front Apron Crossbar Grommet pair is designed from the original part for superior fitment, finish and function. Width: 3-1/2" inches. Height: 3-1/2" inches.
2-3/16" Firewall Grommet
p/n: 17-0044-20
This Firewall Grommet is designed as a firewall pass through for six (6) wires or cables. For eight (8) cylinder models only. For twelve (12) cylinder models see our 17-0045-20.
Side Roof Rail Weatherstrip
p/n: 14-0038-67
Seal, quarter post to folding top, good copy of original. Four (4) piece set. Length: 11.625 inches.
Engine Mount Pad Set
p/n: 50-0224-11
This rear Engine Mount Pad Set is made of a special soft grade rubber, as original. Four (4) piece set.
Headlight Bar Grommet
p/n: 11-0002-14
Grommet, headlight bar-to-radiator shell. Includes clearance groove, faithful detail. 1-1/8 inch inside diameter.
Windshield Weatherstrip Set
p/n: 70-0097-52
This Windshield Weatherstrip Set seals the windshield glass to the body and protects the interior of the vehicle. Fully molded rubber channel for installing front window glass. All corners are correctly molded to fit perfectly.
Axle Rebound Pad
p/n: 40-0373-32
Bumpers, rear axle. Revulcanization service only.Length: 3.0 inches.
Hood bumper
p/n: 70-0013-42
Pads, hood hold-down clamp, mount on clamp swivels to hold hood corners in. Set of four (4) rubber pads in solid brass, chrome plated cups.
Brake and clutch pedal pad
p/n: 11-0008-22
Pad, brake and clutch pedal. Perfect copy of original, superior material and workmanship.
Windshield Weatherstrip Set
p/n: 70-0016-52
This three (3) piece Windshield Weatherstrip Set includes two 16-1/2" side weatherstrip channels and one 48" bottom weatherstrip channel. All corners are correctly molded to fit perfectly.
Rigid Run Channel
p/n: 70-0130-58
Special channel, felt lined rubber, for door upper front post for convertibles with cast upper post. Each piece sixteen (16) inches long.
Axle Rebound Pad
p/n: 15-0003-35
Bumper, frame to axle, rear, with steel core as original.Width: 3.0 inches.
Accelerator Pedal Pad
p/n: 15-0007-40
Pad, accelerator, slipover type for metal pedal, exact copy.Length: 9.4375 inches. Width: 2.50 inches.
Rumble Seat Step Pad
p/n: 11-0012-87
Cover, rumble seat step pad, slipover type, excellent copy.Width: 5.0 inches. Height: 5.0 inches.
Vacuum Clutch / Brake Cylinder Diaphragm
p/n: 50-0063-24
This Electromatic Clutch Control or Brake Vacuum Cylinder Diaphragm is designed from the original part for superior fitment and function. Used in different locations dependent upon vehicle make.