Hood to Cowl Weatherstrip
p/n: 70-4280-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Window Felt Outer Beltline Weatherstrips
p/n: 80-0062-57
This is an Original material style outer side window horizontal weatherstrip set (also known as beltline weatherstrip). This ready to install two (2) piece beltline set includes only the outer seals (the part sealing the outside of the vehicle) for the side windows.
Rigid Run Channel
p/n: 20-0813-58
Channel, rigid division bar run. For front edge of door glass. Two (2) required per truck. Use for either right or left side.
Window Felt Inner Beltline Weatherstrips
p/n: 80-0417-57
This is a high-quality material Window Felt Inner Beltline side window horizontal weatherstrip set (also known as beltline weatherstrip). This two (2) set includes only the inner seals (the part sealing the interior of the car) for the door side windows.
Vent Window Division Post Weatherstrips
p/n: 70-1923-56
This Front Vent Window Division Post Weatherstrip pair is designed from the original part for superior fitment and seal. This piece mounts on the vertical division bar with rivets and the vent glass closes against it.
Quarter Window Lockstrip - CHROME
p/n: 70-3203-52
This Quarter Window Lockstrip is designed from the original part for superior fitment and function. This chrome lockstrip inserts into the weatherstrip to lock in the window glass. Requires 2 sets per vehicle.
Rear Window Gasket without Groove
p/n: 70-4513-83
This Rear Window Gasket for Standard Cabs mounts around the full perimeter of the back glass. This is a standard black EPDM rubber seal with NO reveal molding groove.
Window Locking Strip - Chrome
p/n: 70-2196-52
This Chrome Locking Strip is used to retain windshield gaskets in pickups and vans. Designed from the original part for superior fitment, finish and function. Available in 16ft. lengths.
Window Weatherstrip Lockstrip - Black
p/n: 70-4019-52
This Window Weatherstrip Lockstrip in Black inserts into the weatherstrip to lock in the glass. Made from high quality materials to the original design for a factory like fit and appearance.
Front Door Weatherstrips
p/n: 70-4758-72
This Front Door Weatherstrip pair is designed from the original part for superior fitment and seal. Push-on pin type door weatherstrips mount directly to the full perimeter of the front doors to seal against the van body when closed.
Front Lower Control Arm Bumper
p/n: 20-0202-32
This Front Lower Control Arm Bumper is designed from the original part for superior fitment, finish, and function. This suspension bumper mounts to the front lower control arm to prevent metal to metal contact.
Hood to Cowl Weatherstrip
p/n: 70-1253-42
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. This weatherstrip mounts at the rear of the engine bay directly to the body. Seventy-two (72") inches OAL and includes fifteen (15) 70-1255-42 plastic clips for installation.
Rear Cargo Door Hinge Gaskets Set
p/n: 60-0659-69
This four (4) piece molded Rear Cargo Door Hinge Gasket Set is made to original specifications for proper fitment. Seals are fully molded from top quality rubber to ensure durability, fitment and proper seal.
Taillight Lens Gasket
p/n: 70-3565-15
Gasket, taillight lens mounting gasket. Machine die cut from 1/4" thick sponge rubber. Seals tail light lens to tail light assembly. Included in our kit #70-3566-15.
Clutch Release Lever Boot
p/n: 20-0761-24
This Clutch Release Lever Boot is designed from the original part for superior fitment and seal. This boot is for the clutch release lever to clutch housing.
Door End Cap Fillers
p/n: 70-4673-73
This Door End Cap Filler pair manufactured with soft, yet durable, closed-cell EPDM sponge rubber with galvanized steel cores. Designed from the original part for superior fitment, finish and function.
Front Suspension Rubber Bumper Set
p/n: 82-0176-32
Front Suspension Rubber Bumper Kit - A four (4) piece set with both upper and lower arm rubber bumpers in one set.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-1091-42
This Firewall To Hood Weatherstrip - Cowl Lacing mounts under the rear of the hood on the cowl panel. This is a die-cut extrusion with pre-installed clips as original.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 70-3374-42
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. Measuring 67-1/2” long x 1-1/4” wide to provide complete coverage.
Front Door Vent Window Weatherstrips
p/n: 70-2702-55
These Front Door Vent Window Weatherstrips are designed from the original parts for superior fitment and seal. The pieces are molded as left and right and are one piece with the division post seal.
Axle Rebound Pad
p/n: 20-0647-32
Bumper, rear axle. Two (2) required per Truck. 1965-72: F100, F350 2 W/D (wheel drive), F100, F250 4 W/D (wheel drive).
Trunk or Hatchback Weatherstrip
p/n: 20-2866-84
This Trunk or Hatchback Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Brake and clutch shank seal
p/n: 20-0758-23
Seal, clutch rod to floor. Useage: 1971-72: F100-350 series AFTER Serial #M00,001 1973-79: F100-350 series trucks
Tailgate Weatherstrip
p/n: 70-2434-72
This Tailgate Weatherstrip reproduction is designed from the original part for superior fitment and seal. This weatherstrip mounts on three (3) sides of the tailgate with weatherstrip adhesive (not included).
1973-1978 Chevy And GMC Truck Factory Parts, CD
p/n: 07-1417-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Chevrolet and GMC Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Hood to Cowl Weatherstrip
p/n: 70-3146-42
This three (3) piece Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip set installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Front Fender Splash Shield Fillers
p/n: 70-4924-45
This Front Fender Splash Shield Filler pair is designed from the original part for superior fitment and function. Filler pieces are die cut from quality 3/32" masticated rubber to authentic original dimensions.
Upper Door Weatherstrips - Top of Door
p/n: 20-0819-72
This Upper Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Used as an upper / top of door weatherstrip on both doors. This part was used on 1978-1979 Ford Trucks but can also be retrofitted to 1973-77 Ford Pickups as well to improve the door seal.
Cowl to Fender Filler Weatherstrips
p/n: 70-3940-43
This Cowl To Fender Filler Weatherstrip pair is made from top quality rubber and designed from originals for a superior fitment and seal.
Hood to Radiator Weatherstrip
p/n: 70-4890-43
This Hood to Radiator Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the front of the engine bay to seal between the radiator support / grill and seals against the hood.
Gearshift Knob
p/n: 20-0763-24
This black column shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This reproduction part is a direct screw on replacement for that broken, aged-out original knob.
Windshield Frame Cowl Gasket
p/n: 70-4738-43
This Windshield Frame Cowl Gasket is designed from the original part for superior fitment and seal. A fully molded reproduction of the original. This weatherstrip gasket installs at the lower windshield frame base.
Stabilizer Bar End Link
p/n: 20-0782-33
This Front Stabilizer Bar End Link is used to smooth the transfer between the sway bar and the control arm. Two (2) end links required per truck. For 4x2 (2 wheel drive) models.
Trunk Weatherstrip
p/n: 70-2124-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Trunk Weatherstrip
p/n: 20-0302-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The decklid weatherstrip mounts around the full perimeter of the trunk directly to the body.
Chrome Mylar Locking Strip
p/n: 70-3425-52
This Chrome Mylar Locking Strip inserts into the weatherstrip to lock in the glass for the rear window. The strip is designed to be installed during glass replacement.
Window Weatherstrip Lockstrip - Chrome
p/n: 70-4018-52
This Window Weatherstrip Lockstrip with Chrome Strip inserts into the weatherstrip to lock in the glass. Made from high quality materials to the original design for a factory like fit and appearance.
Trunk Weatherstrip
p/n: 82-0028-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Hood to Cowl Weatherstrip
p/n: 70-4135-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body.
Stabilizer Bar End Link Repair Set
p/n: 20-0783-33
This five (5) piece Stabilizer Bar End Link Repair Set is for the front or rear stabilizer bar. Two (2) per set. Used on Front for 1975-1979 F150-F350 series 4x2. Used on Rear for 1980-1989 F100-F350 series.
Rear Wheel House Seals
p/n: 70-2795-45
This Rear Wheel House Seal pair is designed from the original part for superior fitment and function. Filler seal pieces are die cut from quality masticated rubber to authentic original dimensions.
Window Gasket Locking Strip - Chrome
p/n: 70-1919-52
This chrome appearing Window Gasket Locking Strip is designed from the original part for superior fitment and seal. Locking strip serves as the front or rear window gasket retainer. Sixteen (16') foot length single piece, one application, for complete coverage.
Fuel Neck Grommet
p/n: 70-2284-41
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body. Fully molded out of gasoline resistant BUNA high quality rubber.
Splash Apron Fender Seal
p/n: 20-0877-44
This Splash Apron Fender Seal pair installs from the inner fender panel to the firewall. Made of high quality EPDM rubber and to the original design for a factory like fit.
Door Jamb Wire Loom Grommets
p/n: 70-4870-70
These Door Jamb Wire Loom Grommets go between the door and door jam and allow you to run wires or cables through them. They make great complements to power window kits, shaved door kits, or custom stereo installs.
Hood to Cowl Weatherstrip
p/n: 70-3924-43
This Hood to Cowl Weatherstrip has the proper rubber cross section and is made from top quality rubber to ensure durability and seal. Designed from the original part for a superior fitment and seal.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-0790-42
This Firewall to Hood Weatherstrip is made of high quality EPDM dense rubber and to the original design for a factory like fit and appearance. Comes with pre-drilled mounting holes and mounting clips installed.
Splash Apron / A-Arm Dust Shield
p/n: 70-3058-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Brake and Clutch Pedal Pads
p/n: 70-3003-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A square style direct fit reproduction to replace worn original pedal pads. Manufactured in black rubber.
Window Locking Strip - Black
p/n: 70-2195-52
This extruded Locking Strip is used to retain windshield gaskets in pickups and vans. Designed from the original part for superior fitment, finish and function. Available in 16ft lengths.
Glass Run Channel - Vent Window Delete
p/n: 70-3891-58
This Glass Run Channel pair is for applications where the vent window has been eliminated. One pair fits both driver (Left) and passenger (Right) side doors.
Paint Reseal and Gasket Set
p/n: 70-4310-44
This Paint Reseal Gasket Set contains like original design reproductions for the vehicles specific exterior pieces. These reproductions are die-cut from quality materials to the original design for superior performance, durability, and a factory like fit.
Cowl to Fender Seals
p/n: 70-3340-43
This two (2) piece Cowl to Fender Seal pair is designed from the original part for superior fitment and seal. Fender seals are die cut from quality masticated rubber to authentic original dimensions.
Removable Top Front Weatherstrip - On Fiberglass Roof
p/n: 70-2999-68
This Removable Top Front Weatherstrip is designed from the original part for superior fitment and sealing. This weatherstrip installs directly on the front of the fiberglass roof shell with weatherstrip adhesive glue (not included) and presses against the metal roof cab weatherstrip.
Firewall to Hood Weatherstrip
p/n: 70-3123-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. Installs with the pre-installed clips on the front edge of the cowl.
Taillight Lens Gaskets
p/n: 20-2667-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment, finish and function. These reproduction gaskets fit between taillight lens and taillight housing.
Windshield Wiper Pivot Gaskets
p/n: 20-0808-53
This four (4) piece Windshield Wiper Pivot Gasket set is designed from the original part for superior fitment and seal. This reproduction gasket is die cut from original style EPDM rubber for an authentic fitment, finish and function.
Brake Pedal Pad - Automatic
p/n: 70-4589-22
This reproduction Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pads for automatic transmission models. Detailed and finished to match the original appearance.
Window Locking Strip - Black
p/n: 70-1918-52
This Window Locking Strip is designed from the original part for superior fitment and function. Front or rear window retainer made from top quality black EPDM rubber. Available in 15ft lengths.
Fuel Tank Mounting Isolator Set
p/n: 70-4628-41
This six (6) piece Fuel Tank Mounting Isolator Set is a reproduction of the original style fuel tank isolator set. Replacing or adding the isolator strips and pads can help eliminate noise or friction between the fuel tank straps and the body.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Upper Windshield Corner Molding
p/n: 20-0806-52
This Upper Windshield Corner Molding pair fits the Left and Right Upper Corner. If your corner molding is starting to show it's age, get that factory look back with these new trim corners.
Hood Bumper Set
p/n: 20-0792-42
This Hood Bumper Set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure. Four (4) piece set.
Turn signal light gasket
p/n: 20-0749-16
Gaskets, side marker light. Front and rear. Four (4) piece set.
Brake or Clutch Pedal Pad - Manual
p/n: 60-0709-22
A top-quality rubber Clutch or Brake Pedal Pedal Pad reproduction. One (1) each slip-over type pedal pad installs over the full perimeter of the brake or clutch pedal for a precise, factory fit. For manual transmission model GM vehicles only.
Stabilizer Bar Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
Splash Apron / A-Arm Dust Shield
p/n: 70-3316-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Parking Brake Cable To Floor Seal
p/n: 20-0760-24
This Parking Brake Cable To Floor Seal is designed from the original part for superior fitment, finish and function. The part protects the parking brake cable as it passes through the truck body floor pan.
Brake Pedal Pad
p/n: 70-4590-22
This reproduction Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pads. Detailed and finished to match the original appearance.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Radius Arm Bushing
p/n: 20-0671-36
This Radius Arm Bushing is a quality reproduction of the original factory part. The bushing fits at the frame end of the radius rod on 4-Wheel Drive models. Requires two (2) bushings per side with four (4) total per vehicle.
F-100 Brake Pedal Pad, Automatic
p/n: 70-4485-22
This reproduction F-100 Brake Pedal Pad slips over the full perimeter of the brake or clutch pedal for a precise, factory fit. Replaces original brake pedal pads for automatic transmissions.
F-150 Brake Pedal Pad, Automatic
p/n: 70-4487-22
This reproduction F-150 Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pads for automatic transmissions.
Side Window Glass Run Channel
p/n: 20-0812-58
This Side Window Glass Run Channel is designed from the original part for superior fitment and seal. Single length of flexible window run channel for the sides and top of door windows. For Left or Right side, order two (2) per truck as needed.
Brake Pedal Pad - Automatic
p/n: 60-0710-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. A direct fit to replace worn, heavy wear original brake pedal pads. For GM models with an automatic transmission.
Rear Hatchback Door Window Glass Weatherstrip
p/n: 70-4826-81
This Rear Hatchback Door Window Glass Weatherstrip is designed from the original part for superior fitment and seal. A reproduction of edge channel that surrounds the metal edge were the rear hatch window glass touches the hatch door.
Bronco Script Brake Pedal Pad, Automatic
p/n: 70-4481-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pad for automatic transmissions with power brakes.
Radiator Insulator Pads - Set of 4
p/n: 20-0198-31
This Radiator Insulator Pad set is designed from the original part for superior fitment and function. Molded insulator pads; two (2) long and two (2) short pads for the upper and lower, and for the left and right sides of the radiator. For various applications.
F-100 Brake OR Clutch Pedal Pad
p/n: 70-4484-22
This reproduction F-100 script Brake OR Clutch Pedal Pad slips over the full perimeter of the brake or clutch pedal for a precise, factory fit. Replaces original brake or manual transmission clutch pedal pads.
F-150 Brake OR Clutch Pedal Pad
p/n: 70-4486-22
This reproduction F-150 Brake OR Clutch Pedal Pad slips over the full perimeter of the brake or clutch pedal for a precise, factory fit. Replaces original brake or manual transmission clutch pedal pads.
Hood to Fender Bumper Set
p/n: 20-0213-42
This Hood to Fender Bumper Set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Steering Column - Floor Seal
p/n: 70-3358-36
This Steering Column is designed from the original part for superior fitment and sealing. Seal part is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan inside the vehicle.
Clutch or Brake Pedal Pad
p/n: 20-0848-22
This reproduction Clutch and/or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.