Radiator bracket cushion
p/n: 70-2554-31
Cushions, radiator support, upper. Fully molded, specially designed to duplicate original part.
Clutch Lever Dust Boot
p/n: 70-4760-24
This Clutch Lever Dust Boot covers the opening on your engine bellhousing for manual transmission models. A reproduction manufactured to OEM specifications to install for an authentic fit, finish and function.
Fuel Filler Neck Grommet
p/n: 70-2580-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Brake or Clutch Pedal Pad - Manual
p/n: 60-0709-22
A top-quality rubber Clutch or Brake Pedal Pedal Pad reproduction. One (1) each slip-over type pedal pad installs over the full perimeter of the brake or clutch pedal for a precise, factory fit. For manual transmission model GM vehicles only.
Cowl Grill Seal
p/n: 70-1520-54
Seal, cowl grill to firewall. Die cut dense sponge rubber. Replaces #3860119.
Front Axle Bumper
p/n: 20-1577-33
This Front Axle Bumper is a quality reproduction of the original factory part. These bottoming bump stops are dense rubber blocks that mount with a stud to a front axle bracket.
Splash Apron / A-Arm Dust Shield
p/n: 70-2802-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Cowl grill seal
p/n: 60-0679-54
Weatherstrip, cowl grill to firewall. Used on either end of cowl near fender. Die cut dense sponge rubber.
Rear Leaf Spring Insulator
p/n: 20-2733-32
This Rear Leaf Spring Insulator is an exact replacement of the rear spring center mount rubber insulator block that mounts below the leaf spring. Four (4) required per vehicle. Fits 2-1/2" leaf spring.
Fastback Fold Down Rear Seat To Floor Stop Bumpers
p/n: 20-2884-88
This Fastback Fold Down Rear Seat To Floor Stop Bumper pair is designed from the original part for superior fitment, finish and function. Includes jamb nuts.
Brake Pedal Pad - Manual w/Disc Brakes
p/n: 70-4803-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. A direct fit to replace worn, heavy wear original brake pedal pads. For models with manual transmission and disc brakes.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3062-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Hood to Top of Radiator Weatherstrip
p/n: 20-1083-42
This Hood to Top of Radiator Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the top of the radiator to seal between the radiator and hood.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Radiator Mounting Pads
p/n: 20-0183-31
This Radiator Mounting Pad pair is designed from the original part for superior fitment and function. These upper mounting pads secure and isolate the radiator at its upper mounting point.
Brake Pedal Pad
p/n: 20-1044-22
Pad, brake pedal. Models with automatic transmission and manual brakes.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Steering Column At Floor Seal - with Tilt
p/n: 70-4625-36
This Steering Column At Floor Seal - with Tilt Wheel is designed from the original part for superior fitment and sealing. This gasket is manufactured from top quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Hood to Cowl Weatherstrip
p/n: 70-1694-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Parking Light Lens Gaskets
p/n: 20-0167-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Lens and the Parking Light Housing or Bezel.
Directional and Parking Light Lens Gaskets
p/n: 70-3233-16
This Directional Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Fuel Filler Neck Grommet
p/n: 70-1439-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body. Fits as original.
Steering Column At Floor Seal - without Tilt
p/n: 70-4461-36
This Steering Column At Floor Seal - without Tilt Wheel is designed from the original part for superior fitment and sealing. This gasket is manufactured from top quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Trunk Decklid Weatherstrip
p/n: 20-2859-84
This Trunk Decklid Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk decklid. For Fastback models only.
Quarter Post To Door Window Seals
p/n: 20-2839-79
This Quarter Post To Door Window seal pair is designed from the original part for superior fitment and sealing. These seals are located on the quarter post to window.
Window Locking Strip - Black
p/n: 70-1918-52
This Window Locking Strip is designed from the original part for superior fitment and function. Front or rear window retainer made from top quality black EPDM rubber. Available in 15ft lengths.
Door Bumper Set
p/n: 90-0209-90
This four (4) piece Door Bumper Set is designed from the original part for superior fitment, finish and function. Molded from top quality EPDM dense rubber to ensure durability.
Ulta-Mat Kick Panel Heat and Sound Underlayment
p/n: 70-4782-88
This Ulta-Mat Kick Panel Heat and Sound Underlayment is pre-cut for a direct-fit installation. Underlayment pieces are made from a flexible and lightweight foil facing foam rubber sound and heat insulation material.
Door Handle Gasket Set
p/n: 70-0733-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Parking Light Lens Gaskets
p/n: 70-3073-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Lens and the Parking Light Housing or Bezel.
Front Fender Splash Shield Set
p/n: 20-2762-45
This six (6) piece Front Fender Splash Shield Set is designed from the original part for superior fitment and seal. Includes attaching staples.
Rear spring bushing
p/n: 20-0661-32
Bushing, rear spring front and rear. Useage: 1964-66: F250 4x2's- 4 required 1966: F250 4x4's and all 350's- 2 required 1966-69- Bronco
Hood to Fender Bumper
p/n: 70-2046-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Trunk Decklid Weatherstrip
p/n: 20-2858-84
This Trunk Deckid Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk lid.
Door Bumper
p/n: 70-3035-71
This Door Bumper is designed from the original part and attaches to door with single screw. Typically requires two (2) or four (4) bumpers per vehicle depending on the vehicles year of manufacture.