Parking Light Lens Gaskets
p/n: 20-0045-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Lens and the Parking Light Housing or Bezel.
Tailgate Lower Seal
p/n: 70-4010-85
This Tailgate Lower Seal is properly molded from originals for a factory like fit. The seal is installed using screws, which are included.
Taillight Housing to Body Seals
p/n: 70-3488-15
This Taillight Housing to Body Seal pair is designed from the original part for superior fitment and seal. These reproduction seals fits between the taillight housing and the vehicle body.
Door Hinge Seal Set
p/n: 20-0909-73
This four (4) piece Door Hinge Seal set is designed from the original part for superior fitment and seal. This Door hinge to door seal set is for both doors.
Hood Bumper
p/n: 70-1543-42
Bumper, hood adjustable. Fully molded rubber, two (2) required per car. Does not include bolt.
Door Glass Flexible Run Channel
p/n: 20-0894-58
This Door Glass Flexible Run Channel is designed from the original part for superior fitment, finish and function. This felt lined door glass run inserts into the top and backside of the door. Allows door glass to roll up and down freely.
Door Handle Gasket Set
p/n: 60-0640-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Adjustable Hood Bumper
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Hood to Fender Bumper
p/n: 60-0542-42
This Hood to Fender Bumper set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Tailgate Bumper
p/n: 20-0694-45
These Tailgate Bumpers are sold as pair. The bumpers fit in brackets and comes with chains.
Quarter Panel Drain Plugs
p/n: 20-2769-45
This Quarter Panel Drain Plug pair is a quality reproduction of the original factory part. These rubber plugs fit inside the quarter panel area to seal-out weather and environmental elements.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Hood Bumper
p/n: 70-0987-42
Bumper assembly, with stud. Two (2) or four (4) used per car as required.Height: 3.25 inches.
Clutch or Brake Pedal Pad
p/n: 20-0848-22
This reproduction Clutch and/or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Radiator Shroud Seal
p/n: 20-0191-31
Seal, radiator side air deflector. Three (3) inch by fourteen and one eighth (14-1/8) inch.
Firewall to Hood Weatherstrip
p/n: 20-2750-42
This Firewall to Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Retractable Headlight Seal
p/n: 20-0144-14
Seals, headlight opening cover plate. With headlight covers.
Hood Bumper
p/n: 20-0209-42
Bumper, hood on rear of fender. Rubber button tip only. Two (2) piece set.
Hood Bumper
p/n: 70-0907-42
Bumper, hood front aligning. Correct design with proper screw thread.Height: 2.50 inches.