Quarter Post To Window Seals
p/n: 70-4766-79
This Quarter Post To Door Window seal pair is designed from the original part for superior fitment and sealing. These seals are located on the quarter post to window.
Front Bow Weatherstrip
p/n: 20-2798-64
This Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This header seal installs directly to the windshield frame to seal between the soft top and the top of the windshield.
Hood to Cowl Firewall Weatherstrip
p/n: 20-2752-42
This Hood to Cowl Firewall Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts with the included clips at the rear of the engine bay firewall directly to the body.
Quarter Panel Drain Valves
p/n: 20-2770-45
These Quarter Panel Drain Valves are constructed of a durable rubber and are a direct-fit replacement. This product is sold as a pair.
Rear Leaf Spring Insulator
p/n: 20-2733-32
This Rear Leaf Spring Insulator is an exact replacement of the rear spring center mount rubber insulator block that mounts below the leaf spring. Four (4) required per vehicle. Fits 2-1/2" leaf spring.
Upper Control Arm Bumper
p/n: 20-2727-32
This Upper Control Arm Bumper is designed from the original part for superior fitment and function. A molded rubber bumper which serves as a bump stop for the front suspension.
Firewall to Hood Weatherstrip
p/n: 70-3465-42
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile made in sponge rubber. This weatherstrip installs at the rear of the engine bay to seal between the hood and the vehicle firewall.
Splash Apron / A-Arm Dust Shield Set
p/n: 70-3057-45
This four (4) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Front Axle Bumper
p/n: 20-1577-33
This Front Axle Bumper is a quality reproduction of the original factory part. These bottoming bump stops are dense rubber blocks that mount with a stud to a front axle bracket.
Brake or Clutch Pedal Pad - Manual
p/n: 60-0709-22
A top-quality rubber Clutch or Brake Pedal Pedal Pad reproduction. One (1) each slip-over type pedal pad installs over the full perimeter of the brake or clutch pedal for a precise, factory fit. For manual transmission model GM vehicles only.
Cornering Light Lens Gaskets
p/n: 70-3100-17
This Cornering Light Lens Gasket pair is designed from the original part for superior fitment and seal. These quality reproduction gaskets fit between the cornering light lens and the cornering light housing or bezel.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-2798-45
This Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pair pieces are die cut from quality masticated rubber to authentic original dimensions. This filler pair fits over suspension a-arms and inside front inner fenders.
Clutch Lever Dust Boot
p/n: 70-4760-24
This Clutch Lever Dust Boot covers the opening on your engine bellhousing for manual transmission models. A reproduction manufactured to OEM specifications to install for an authentic fit, finish and function.
Rear Spoiler Mounting Gaskets
p/n: 20-2872-87
This Rear Spoiler Mounting Gasket pair is designed from the original part for superior fitment and seal. These gasket fit between the rear spoiler mounting pedestals and the trunk decklid.
Stabilizer Bar Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
AC Condenser Mount
p/n: 70-0964-31
Mount, air conditioning condenser. Four (4) used per car.Length: 1.0 inches. Width: .75 inches.
Hood to Cowl Weatherstrip
p/n: 70-2807-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body.
Splash Apron / A-Arm Dust Shield
p/n: 70-3316-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Splash Apron / A-Arm Dust Shield
p/n: 70-3335-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Hood bumper
p/n: 20-0875-42
Bumpers, hood side. 1967-69 needs 1 pr. per truck, 1970-72 needs 2 pr. per truck.
Stabilizer Bar End Link Repair Set
p/n: 20-1068-33
This eleven (11) piece Stabilizer Bar End Link Repair Set is designed to withstand harsh conditions without deteriorating. Two (2) end link sets required per car.
Trunk Decklid Bumper Stop
p/n: 82-0160-87
This Trunk-Decklid Bumper Stop is a quality reproduction of the original factory part. This adjustable rubber bumper attaches to the vehicle body to support / cushion the trunk lid closure.
Air Cleaner Lid Gasket
p/n: 20-2701-20
This Air Cleaner Lid gasket is designed from the original part for superior fitment and sealing. This cut-to-fit gasket glues to the air cleaner lid to seal between the lid and air filter element housing. This gasket is for Six (6) Cylinder engine models.
Door Glass Run Channel
p/n: 70-4313-58
This Door Glass Run Channel is designed from the original part for superior fitment and seal. The window glass run channel presses into the door channel at the top and back part of the door. This single piece fits either the driver (LH) OR the passenger (RH) side front door.
Body Mounting Pad
p/n: 70-2165-48
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. Used on the bottom of most mounting locations.
Hood To Cowl Weatherstrip
p/n: 70-4835-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This weatherstrip installs at the rear of the engine bay to seal between the hood and vehicle body cowl.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Firewall To Hood Weatherstrip - Cowl Lacing
p/n: 70-4014-42
This Firewall To Hood Weatherstrip - Cowl Lacing comes with pre-drilled mounting holes and mounting clips installed. Made of high-quality EPDM rubber and to the original design for a factory like fit and appearance.
Front Suspension Bumper
p/n: 20-0080-32
Bumper for front suspension upper arm. Measures three eighths (3/8) inch by sixteen (16) by eleven sixteenths with (11/16) inch bolt thread.
Front Inner Fender To Frame Fillers
p/n: 70-3243-45
This Front Inner Fender To Frame Filler pair is designed from the original part for superior fitment and function. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces attach to inner fender and fill the gap to the frame.
Axle Rebound Pad
p/n: 20-2730-32
Bumpers, outer rear axle. Mounts on frame rail. Push in type. Two (2) required per car.
Radiator Top Seal
p/n: 20-0200-31
Seal, top of radiator support to radiator seal. Twenty three and thirteen sixteenths (23-13/16) inches long.
Radius Arm Bushing
p/n: 20-0671-36
This Radius Arm Bushing is a quality reproduction of the original factory part. The bushing fits at the frame end of the radius rod on 4-Wheel Drive models. Requires two (2) bushings per side with four (4) total per vehicle.
Torsion bar bushing
p/n: 20-0670-36
Bushing, front radius rod. Front and rear. Four (4) required per Truck.
Air Cleaner Lid Gasket
p/n: 20-2700-20
This Air Cleaner Lid gasket is designed from the original part for superior fitment and sealing. This cut-to-fit gasket glues to the air cleaner lid to seal between the lid and air filter element housing. This gasket is for 302, 351 and 390 V8 engine models.
Tailgate Weatherstrip
p/n: 70-4839-85
This Tailgate Weatherstrip reproduction is designed from the original part for superior fitment and seal. This weatherstrip mounts on 3 sides of the tailgate with weatherstrip adhesive (not included).
Vent Division Bar Weatherstrip
p/n: 70-1921-56
Front vent window division post seal. Fully molded with metal core and pre-drilled holes.
Brake Pedal Pad - Automatic
p/n: 60-0710-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. A direct fit to replace worn, heavy wear original brake pedal pads. For GM models with an automatic transmission.
Radiator Insulator Pads - Set of 4
p/n: 20-0198-31
This Radiator Insulator Pad set is designed from the original part for superior fitment and function. Molded insulator pads; two (2) long and two (2) short pads for the upper and lower, and for the left and right sides of the radiator. For various applications.
Splash Apron
p/n: 20-0878-44
This two (2) piece Splash Apron is designed from the original part for superior fitment and seal. Front fender apron to firewall lower seal. Staples included.
Clutch Pedal Rod Boot
p/n: 20-1049-23
This Clutch Pedal Rod Boot is designed from the original part for superior fitment and seal. Accordion style boot seals the clutch rod to the floor.
Rear Liftgate Bumpers
p/n: 70-4833-87
This fully molded Rear Liftgate Bumper pair is a quality reproduction of the original factory part. These two (2) rubbers bumpers attach to the vehicle rear liftgate to support / cushion the liftgate closure.
Taillight Lens Gasket
p/n: 20-0837-15
Gaskets, taillight lens. Rectangular type. For style-side trucks.
F-100 Brake OR Clutch Pedal Pad
p/n: 70-4484-22
This reproduction F-100 script Brake OR Clutch Pedal Pad slips over the full perimeter of the brake or clutch pedal for a precise, factory fit. Replaces original brake or manual transmission clutch pedal pads.
Hood to Fender Bumper Set
p/n: 20-0213-42
This Hood to Fender Bumper Set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Hood Bumper
p/n: 20-0211-42
Bumper, hood on rear of fender. Rubber button tip only. Two (2) piece set.
Steering Column - Floor Seal
p/n: 70-3358-36
This Steering Column is designed from the original part for superior fitment and sealing. Seal part is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan inside the vehicle.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Clutch or Brake Pedal Pad
p/n: 20-0848-22
This reproduction Clutch and/or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
2-7/16" Floor Plug
p/n: 35-3508-45
This Floor Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability. Up to ten (10) used per vehicle.
Adjustable Hood Bumper
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Door Handle Gasket Set
p/n: 60-0640-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Hood to Fender Bumper
p/n: 60-0542-42
This Hood to Fender Bumper set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Tailgate Bumper
p/n: 20-0694-45
These Tailgate Bumpers are sold as pair. The bumpers fit in brackets and comes with chains.