Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Directional & Parking Light Lens Gaskets
p/n: 70-3096-16
This Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Directional or Back Up Light Lens Gaskets
p/n: 70-3776-16
This Directional Turn Signal or Back Up Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Light Lens and the Light Housing or Bezel.
Division Bar Glass Run Channel
p/n: 20-1113-58
This Division Bar Glass Run Channel pair is designed from the original part for superior fitment and function. This glass run channel holds the glass in place.
Division Bar Glass Run Channels
p/n: 20-0239-58
This two (2) piece Division Bar Glass Run Channel pair installs between the front of door glass and the back of the vent window.
Door Auxiliary Weatherstrips
p/n: 70-3932-73
This Door Auxiliary ("J-Strip") Weatherstrip pair is designed from the original parts for superior fitment and seal. These two (2) glue-on strips, one for each door, are manufactured for a factory like fit.
Door Body Above Door Weatherstrips
p/n: 70-3933-61
This pair of Door Body Above Door Weatherstrips, provides one seal for each door. Designed from originals and made for a like factory fit.
Door Bumper
p/n: 70-1563-71
This fully molded Door Bumper is quality reproduction of the original factory part. This rubber bumper attaches to the vehicle body to support / cushion the door closure.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door Bumper
p/n: 33-0981-71
This Door Bumper is designed from the original part for superior fitment, finish and function. Molded with push in carrot retainers, this bumper is commonly used as a upper door bumper on GM models.
Door Bumper
p/n: 20-0067-71
This Door Bumper is designed from the original part for an authentic fit, finish and function. Installs on back edge of door. Usually two (2) to eight (8) per vehicle.
Door Bumper
p/n: 70-3035-71
This Door Bumper is designed from the original part and attaches to door with single screw. Typically requires two (2) or four (4) bumpers per vehicle depending on the vehicles year of manufacture.
Door Bumper
p/n: 33-0503-71
This fully molded 3/4” Door Bumper is quality reproduction of the original factory part. Not a generic substitute but manufactured just like the factory original.
Door Bumper
p/n: 70-2045-71
This Door to Body Bumper is quality reproduction of the original factory part. Use varies depending upon model and body type. Some models uses four (4) bumpers for front doors and four (4) for rear doors.
Door Bumper - Lower
p/n: 70-1605-71
This fully molded Door Bumper is quality reproduction of the original factory part. This rear of door lower bumper attaches to the vehicle body to support / cushion the door closure.
Door Bumper - Lower
p/n: 70-3308-71
This Lower Door Bumper is designed from the original part for superior fitment and function. Bumper pushes into slot on door at bottom.
Door Bumper Set
p/n: 90-0209-90
This four (4) piece Door Bumper Set is designed from the original part for superior fitment, finish and function. Molded from top quality EPDM dense rubber to ensure durability.
Door Bumper, Upper / Lower
p/n: 20-2825-71
This Door Bumper is a quality reproduction of the original factory part. Upper / Lower push-in type. Four (4) required per car.
Door Conduit Set - Wiring - Vacuum Hoses
p/n: 60-0655-21
A six (6) piece Door Conduit set for the front door electric window wires or power lock vacuum lines. The set includes two (2) hoses and two (2) pairs of grommets.
Door Conduit Set for Power Windows
p/n: 60-0653-21
This Door Conduit Set is designed from the original part for superior fitment and function. Conduit contains the front door electric window wires and/or power lock vacuum lines. Set includes two (2) hoses and three (3) pair of grommets. Length: 12.0 inches.
Door drain hole seal
p/n: 70-3034-70
Seal, door inner panel drain. Attaches to bottom of door with one (1) carrot retainer on either end.
Door Glass Bumper
p/n: 20-1172-71
This lower door glass bumper is designed from the original part for superior fitment. If your door window goes too low, or makes a metallic sound when lowered all the way down, you likely need to replace this lower door glass bumper.