Vent Window Pivot Post Rivet
p/n: 70-4757-98
This Vent Window Pivot Post Rivet is used to replace the hinge pivot rivet for both left and right vent window assemblies. Commonly used for General Motors car and truck models.
Hood and Fender Bumper
p/n: 70-3446-42
This Hood / Fender Bumper is a quality reproduction of the original factory part. This adjustable rubber bumper attaches to the front fender to support / cushion the hood closure.
Hood to Fender Bumper
p/n: 82-0022-42
This single molded Hood to Fender Bumper is a quality reproduction of the original factory part. This rubber bumper attaches to the front fender to support / cushion the hood closure. Usually requires four (4) bumpers each per vehicle.
Lock Cylinder Gasket
p/n: 60-0641-69
This Lock Cylinder Gasket is die cut from one-thirty-second (1/32) inch neoprene.
Corner Joint Sleeves
p/n: 70-3720-52
Corner Joint Sleeve pair for the bottom corners of rear window gaskets that require a locking strip. These joint sleeves have a Chrome look to match the Mylar locking strip. Joint sleeves can also be painted black when using with the black rubber locking strip.
Cowl Top Plug
p/n: 20-1813-20
This Cowl Top Plug is designed from the original part for an authentic fit, finish, and appearance. This plug installs in the access hole in cowl top.
Hood Side Bumper
p/n: 20-0953-42
This Hood Side Bumper is a quality reproduction of the original factory part. This rubber bumper mounts on the front fender to support / cushion the hood closure. Usually requires two (2) bumpers each per vehicle.
Hood to Fender Bumper
p/n: 70-4176-42
This Hood to Fender Bumper is a quality reproduction of the factory part. This rubber bumper attaches to the front fender to support or cushion the hood closure. Usually requires four (4) bumpers each per vehicle.
Trunk Bumpers - Coupe or Convertible
p/n: 70-4732-87
This Trunk Bumper pair is a quality reproduction of the original factory part. These dense rubber bumpers attach to the vehicle body to support / cushion the trunk lid closure.
1" Trunk Weatherstrip
p/n: 70-0510-85
This Trunk Weatherstrip was designed from an original part for a specific application but has many uses outside of its original purpose. Available by the foot.
Trunk - Decklid Bumper
p/n: 70-3528-87
This Trunk-Decklid Bumper is a quality reproduction of the original factory part. This adjustable rubber bumper attaches to the vehicle body to support / cushion the trunk lid closure.
Peel-N-Stick Trunk Weatherstrip
p/n: 70-0510-WT
This Peel-N-Stick Trunk Weatherstrip is made from a high-quality EPDM sponge rubber. Available by the foot.
Liftgate Upper Edge Weatherstrip
p/n: 70-4139-85
This Liftgate Upper Edge Weatherstrip seal is designed from the original part for superior fitment and seal. This weatherstrip mounts on the liftgate and seals the upper edge.
Vent Window Rivets and Setting Tool
p/n: 70-4789-70
This Vent Window Rivet pair and Setting Tool includes the peening punch and step rivets to replace the hinge pivot rivet for both left and right vent window assemblies.
Pickup tie down mounting pad
p/n: 20-0885-45
Pad, pickup box tie down hook. Eight (8) required per truck.
Steering Column At Floor Seal
p/n: 70-3490-36
This Steering Column At Floor Seal is designed from the original part for superior fitment and sealing. The seal is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Tailgate Bumper
p/n: 20-0694-45
These Tailgate Bumpers are sold as pair. The bumpers fit in brackets and comes with chains.
Hood to Fender Bumper
p/n: 70-2756-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Adjustable Hood Bumper
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Hood To Fender Bumper Set
p/n: 70-2872-42
These Hood to Fender Bumper are a quality reproduction of the original factory part. The rubber bumper attaches to the front fender to support / cushion the hood closure. Four (4) piece set for two (2) bumpers per side.
Rear Hatch Door Bumpers
p/n: 70-4730-87
This Rear Hatch Door Bumper pair is a quality reproduction of the original factory part. These adjustable rubber bumpers attach to the rear hatch door to prevent the hatch lid from vibrating.
Clutch or Brake Pedal Pad
p/n: 20-0848-22
This reproduction Clutch and/or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Steering Column - Floor Seal
p/n: 70-3358-36
This Steering Column is designed from the original part for superior fitment and sealing. Seal part is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan inside the vehicle.
F-150 Brake OR Clutch Pedal Pad
p/n: 70-4486-22
This reproduction F-150 Brake OR Clutch Pedal Pad slips over the full perimeter of the brake or clutch pedal for a precise, factory fit. Replaces original brake or manual transmission clutch pedal pads.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
F-100 Brake OR Clutch Pedal Pad
p/n: 70-4484-22
This reproduction F-100 script Brake OR Clutch Pedal Pad slips over the full perimeter of the brake or clutch pedal for a precise, factory fit. Replaces original brake or manual transmission clutch pedal pads.
T-Top Trim Panel to Latch Handle Seals
p/n: 20-2806-67
This T-Top Trim Panel to Latch Handle Seal pair is designed from the original part for superior fitment and seal. These seals glue onto the plastic trim panel where latch handle goes through the panel.
Bronco Script Brake Pedal Pad, Automatic
p/n: 70-4481-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pad for automatic transmissions with power brakes.
Rear Hatchback Door Window Glass Weatherstrip
p/n: 70-4826-81
This Rear Hatchback Door Window Glass Weatherstrip is designed from the original part for superior fitment and seal. A reproduction of edge channel that surrounds the metal edge were the rear hatch window glass touches the hatch door.
Brake Pedal Pad - Automatic
p/n: 60-0710-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. A direct fit to replace worn, heavy wear original brake pedal pads. For GM models with an automatic transmission.
F-100 Brake Pedal Pad, Automatic
p/n: 70-4485-22
This reproduction F-100 Brake Pedal Pad slips over the full perimeter of the brake or clutch pedal for a precise, factory fit. Replaces original brake pedal pads for automatic transmissions.
F-150 Brake Pedal Pad, Automatic
p/n: 70-4487-22
This reproduction F-150 Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pads for automatic transmissions.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Brake Pedal Pad
p/n: 70-4590-22
This reproduction Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pads. Detailed and finished to match the original appearance.
Splash Apron / A-Arm Dust Shield
p/n: 70-3316-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Stabilizer Bar Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
Lower Radiator Mount Insulators
p/n: 20-0936-31
This Lower Radiator Mount Insulator pair is designed from the original part for superior fitment and seal. Left and Right lower mounting pads for six (6) or eight (8) cylinder engines.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Fuel Tank Mounting Isolator Set
p/n: 70-4628-41
This six (6) piece Fuel Tank Mounting Isolator Set is a reproduction of the original style fuel tank isolator set. Replacing or adding the isolator strips and pads can help eliminate noise or friction between the fuel tank straps and the body.
Window Locking Strip - Black
p/n: 70-1918-52
This Window Locking Strip is designed from the original part for superior fitment and function. Front or rear window retainer made from top quality black EPDM rubber. Available in 15ft lengths.
Inside Door Handle Gaskets
p/n: 70-4811-69
This Inside Door Handle Gasket pair is designed from the original part for an authentic fit, finish, and appearance. Slips onto edge of hole where door handle comes out of the door panel.
Brake Pedal Pad - Automatic
p/n: 70-4589-22
This reproduction Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. Replaces original brake pedal pads for automatic transmission models. Detailed and finished to match the original appearance.
Convertible and T-Top Retainer Weatherstrip
p/n: 20-2805-67
This Convertible and T-Top Retainer Weatherstrip fits between the body and the metal retainer that holds the weatherstrip in place. One (1) roll per vehicle.
Removable Top Front Weatherstrip - On Fiberglass Roof
p/n: 70-2999-68
This Removable Top Front Weatherstrip is designed from the original part for superior fitment and sealing. This weatherstrip installs directly on the front of the fiberglass roof shell with weatherstrip adhesive glue (not included) and presses against the metal roof cab weatherstrip.
Cowl to Fender Seals
p/n: 70-3340-43
This two (2) piece Cowl to Fender Seal pair is designed from the original part for superior fitment and seal. Fender seals are die cut from quality masticated rubber to authentic original dimensions.
Paint Reseal and Gasket Set
p/n: 70-4310-44
This Paint Reseal Gasket Set contains like original design reproductions for the vehicles specific exterior pieces. These reproductions are die-cut from quality materials to the original design for superior performance, durability, and a factory like fit.
Cobra Clutch and Brake Pedal Pads
p/n: 70-4201-22
This reproduction Cobra Clutch and Pedal Pad pair mounts around the full perimeter of the brake and clutch pedals for a precise, factory fit. Replaces original pedal pads. Manufactured with a thick, quality rubber construction and an embossed striking Cobra emblem on each pad.
Window Locking Strip - Black
p/n: 70-2195-52
This extruded Locking Strip is used to retain windshield gaskets in pickups and vans. Designed from the original part for superior fitment, finish and function. Available in 16ft lengths.
Splash Apron / A-Arm Dust Shield
p/n: 70-3058-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
T-Top Headliner Retainer
p/n: 70-4652-88
This T-Top Headliner Retainer is designed from the original part for superior fitment, finish and function. This retainer strip pinches the headliner to the body to hold it in place. Sold Individually - Purchase two (2) to complete the driver and passenger overhead panel.
Hood to Cowl Weatherstrip
p/n: 70-3924-43
This Hood to Cowl Weatherstrip has the proper rubber cross section and is made from top quality rubber to ensure durability and seal. Designed from the original part for a superior fitment and seal.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-2799-45
This Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pair pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Fuel Neck Grommet
p/n: 70-2284-41
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body. Fully molded out of gasoline resistant BUNA high quality rubber.
Removable Top Front Weatherstrip - On Metal Cab Roof
p/n: 70-3000-68
This Removable Top Front Weatherstrip is designed from the original part for superior fitment and sealing. This part fits on the rear of the metal cab roof and seals against the removable fiberglass top when the top is placed on the vehicle.
Top of Door Weatherstrips - Roof Rail
p/n: 70-4022-73
This Top of Door Weatherstrip - Roof Rail pair for the left and right side doors seal the door window frame to the roof hardtop and to the windshield frame.
Engine Top Cover Weatherstrip
p/n: 70-4750-88
This Engine Top Cover Gasket is an original design reproduction made from top quality sponge rubber. This gasket attaches between the removable engine cover ("doghouse") and the vehicle firewall / floorboard.
Window Gasket Locking Strip - Chrome
p/n: 70-1919-52
This chrome appearing Window Gasket Locking Strip is designed from the original part for superior fitment and seal. Locking strip serves as the front or rear window gasket retainer. Sixteen (16') foot length single piece, one application, for complete coverage.
Body Plug Set
p/n: 70-4648-20
This thirty (30) piece Body Plug set is designed from the original parts for superior fitment and sealing. Made from high quality EPDM dense rubber, this set replaces dried, broken, and missing body plugs.
Firewall to Hood Weatherstrip
p/n: 70-4200-43
This Firewall to Hood Weatherstrip is designed from the original part for superior fitment and seal. This seal has the proper cowl radius to fit correctly. Mounts with ten (10) pre-installed clips at the rear of the engine bay directly to the body.
Stabilizer Bar End Link Repair Set
p/n: 20-0783-33
This five (5) piece Stabilizer Bar End Link Repair Set is for the front or rear stabilizer bar. Two (2) per set. Used on Front for 1975-1979 F150-F350 series 4x2. Used on Rear for 1980-1989 F100-F350 series.
Trunk Weatherstrip
p/n: 20-2865-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Hood to Cowl Weatherstrip
p/n: 70-4135-43
This Hood To Cowl Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body.
AC Condenser - Lower Mount
p/n: 70-2713-31
This AC Condenser - Lower Mount pair is designed from the original part for superior fitment and function. These mounts install to isolate and reduce road vibrations to the air conditioning condenser. Replaces aged, broken or missing mounts.