Front Stabilizer Bushing
p/n: 30-0363-33
Bearings or bushings, front stabilizer rod. One (1) pair used per vehicle. Fully molded rubber.
Front Stabilizer Bushing
p/n: 60-0088-34
This Front Stabilizer Bushing pair is fully molded from EPDM dense rubber to ensure durability. Used to connect the stabilizer bar to the vehicle frame. Two (2) required per car.
Front Stablizer Bar End Link Kit
p/n: 70-0574-33
Kit, front stabilizer bar link assembly replacement. Twenty two (22) piece set for both sides of one (1) car. Hex head bolt. 3/8"-16nc x 8-7/8" lg. Comes with metal sleeve, metal cup washers and rubber grommets.
Front Suspension Bumper
p/n: 27-0080-32
This Front Suspension Bumper, front suspension lower A-arm, is made from high-quality EPDM rubber for a precise, factory fit.
Front suspension bushing
p/n: 20-2474-32
Seal, front suspension lower control arm outer. Four (4) required per car.
Front suspension bushing
p/n: 20-2470-32
Seal, front suspension. Inner lower arm.Qty Required:4 Four (4) required per car.
Front suspension bushing
p/n: 20-2471-32
Seal, front suspension. Inner upper arm.Qty Required:4 Four (4) required per car.
Front suspension bushing
p/n: 20-2473-32
Seal, front suspension outer upper arm. Four (4) required per car.
Front Upper Engine Mount
p/n: 20-0503-11
This Front Upper Engine Mount is made of a quality dense rubber for maximum durability. Designed from original specifications for a correct fit and appearance.
Fuel Filler Neck Grommet
p/n: 60-0512-41
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body. Fully molded rubber, slightly angled and oblong in shape.
Fuel Neck Grommet
p/n: 70-1616-39
Grommet, fuel neck. Fully molded rubber with retaining flange. Three and eleven sixteenths inch (3-11/16") outside diameter by two and one eighth inch (2-1/8") inside hole diameter by nine sixteenths inch (9/16") height.
Fuel Neck Grommet
p/n: 60-0149-41
Grommet, fuel filler neck (1955-1st type). Oblong fully molded rubber with retaining flange. Three and seven eighths inch (3-7/8") outside width by five and one eight inch (5-1/8") outside length by one and one eighth inch (1-1/8") height.
Fuel Neck Grommet
p/n: 10-0123-41
Grommet, fuel filler neck. Fully molded soft flexible rubber. Two and seven sixteenths inch (2-7/16") outside diameter by one and seven sixteenths inch (1-7/16") inside hole diameter by five sixteenths (5/16") height.
Fuel Neck Grommet
p/n: 60-0271-41
Grommet, fuel filler neck. Oblong shaped molded rubber with retaining flange. Three and three fourths inch (3-3/4") outside length by three and five eighths inch (3-5/8") outside width.
Fuel Tank Filler Neck Connection Hose
p/n: 20-1584-39
This Fuel Tank Filler Neck Connection Hose is designed from the original part for superior fitment and function. Connects the fuel tank to the fuel filler pipe.
Fuel Tank Filler Neck Grommet
p/n: 20-0345-39
This Fuel Tank Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Fuel Tank Filler Neck Grommet - Panel Truck
p/n: 20-0486-39
This Fuel Tank Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck at the vehicle body panel.
Fuel Tank Support Pad
p/n: 20-0425-41
This Fuel Tank Support Pad pair installs between the fuel tank and floor to reduce noise. Designed from original specifications so it fits correctly.
Gearshift Boot
p/n: 70-2126-24
Boot, transmission gear hand shift lever. Molded in pliable black rubber which may be painted if needed for restoration.
Gearshift Boot - Black
p/n: 20-0334-26
This reproduction Black Gearshift Boot is designed from the original part for an authentic fit, finish, and appearance.
Gearshift Boot - Brown
p/n: 20-2166-26
This Gearshift Boot is designed from the original part for superior fitment and seal. This boot fits over the gearshift tower to make a weathertight connection for the transmission gearshift rod as it passes up through the vehicle floorboard.
Gearshift Bushing
p/n: 60-0237-24
This Gearshift Bushing is fully molded and designed from the original part for superior fitment and seal. This bushing is made from high-quality EPDM dense rubber to provide excellent durability. Designed for the gearshift shaft lever, large type.
Gearshift Floorplate
p/n: 20-0464-88
Seals, transmission cover to floor. Cork and rubber. Three (3) piece set.
Gearshift Knob
p/n: 20-0461-24
This black ball column shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This reproduction part is a direct push on replacement for that broken, aged-out original knob.
Gearshift Knob
p/n: 20-0583-24
This black floor shift lever Gearshift Knob is designed from the original part for a superior fit and finish. This reproduction part is a direct screw on replacement for that broken, aged-out original knob.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Glovebox or Fuel Tank Filler Door Bumpers
p/n: 20-1220-88
This Glovebox or Fuel Tank Filler Door Bumper pair is a quality reproduction of the original factory part. This push on rubber bumper attaches to support / cushion the glovebox or filler door closure.
Gravel Pan Welt
p/n: 10-0121-45
This Gravel Pan Welt is made of a high quality EPDM dense rubber extrusion. Sold as a ten (10) foot strip.
Gravel Shield Bumper
p/n: 33-0286-30
Bumper, rear gravel shield, anti-rattle. Five (5) or more used per car. Fully molded rubber. Replaces factory #1320392.
Gravel Shield Bumper Set
p/n: 60-0146-30
This Gravel Shield Bumper Set is used as a rear bumper deflector. Also used between the radiator grille and the lower panel. Two (2) required per car. Designed from the original part for superior fitment and seal.
Hardtop Roof Rail Weatherstrips
p/n: 20-3103-68
This Hardtop Roof Rail Weatherstrip pair fits on the roof of the vehicle and seals the side window when the window is fully raised.
Harmonic balancer service
p/n: 70-1047-12
Engine harmonic balancer. Revulcanization service only. Send in your old, rebuildable balancer and pulley assembly.
Headlight Bucket To Fender Gasket
p/n: 20-1542-14
This Headlight Bucket To Fender Gasket is designed from the original part for superior fitment and seal. These gasket fits the headlight bucket and front fender.
Headlight Door To Lens Ring Seals
p/n: 70-0389-14
This Headlight Door To Lens Ring seal pair is designed from the original part for superior fitment and function. The part works to seal between the headlight door housing and the headlight retaining ring. The part is a single lip type seal for sealed beam headlights.
Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Headlight Mounting Pad
p/n: 10-0122-14
Pad, headlight housing to the mounting bracket that secures the housing to the fender.
Headlight Mounting Pad
p/n: 30-0142-14
Gaskets, headlight body mounting to fender. Cut to exact size as original.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Headliner Retainer Grommet
p/n: 70-1713-88
Grommet, headliner bow end. Twelve (12) required per car.Length: 1.4375 inches.
Heater control valve seal
p/n: 50-0356-20
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water. For all except right-hand drive.
Hinge Pillar Weatherstrip
p/n: 20-3092-63
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Hinge Pillar Weatherstrip
p/n: 60-0084-63
This Hinge Pillar Weatherstrip attached to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Hinge Pillar Weatherstrip
p/n: 60-0630-68
Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Hinge Seal Set
p/n: 60-0285-69
Seal, back door hinge, outside. A four (4) piece set. Some vehicles require two (2) sets.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
Hood Bumper
p/n: 50-0277-42
Bumper, hood side to fender ledge. Metal core molded in as original.Width: 1.875 inches. Height: .8125 inches.
Hood Bumper
p/n: 50-0159-42
Bumper, hood ledge corner at shroud.Width: 1.25 inches. Height: .5 inches.
Hood Bumper Set
p/n: 20-0446-42
This twelve (12) piece Hood Bumper set is designed from the original parts for superior fitment and function. This set fits F-Series Trucks.
Hood Bumper Set
p/n: 20-3003-42
This ten (10) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Hood Bumper Set
p/n: 33-0680-42
This eight (8) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Hood Side Upper Bumper
p/n: 70-2617-42
This Hood Side Upper Bumper is fully molded with top quality EPDM rubber. The authentic configuration for 1/4" hole. Six (6) bumpers typically required per vehicle.
Hood to Cowl Bumper
p/n: 70-1248-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips, .34 inch high. Use as required four (4) to six (6) per car.
Hood to Cowl Bumper
p/n: 70-1249-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips. Use as required, four (4) to six (6) per car.
Hood to Cowl Bumper
p/n: 70-1247-42
Bumper, hood to cowl, intermediate. Attaches to our hood to cowl weatherstrips, .28 inch high. Use as required four (4) to six (6) per car.