Splash Apron / A-Arm Dust Shield
p/n: 70-3232-45
This two (2) piece Splash Apron / A-Arm Dust Shield pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Front Engine Mount
p/n: 20-0018-11
This right or left Front Engine Mount is designed from original for correct fitment and function. Rubber bonded to inner metal core with bolt and mounting holes for durability and proper engine vibration isolation.
Wiper Transmission Gasket
p/n: 60-0593-53
Wiper Transmission Gasket - This is the seal for the wiper motor crank. For two (2) speed wiper motors only. These parts are made of the highest quality and authenticity. Replaces # 4906021.
Clutch and Brake Pedal Pads
p/n: 60-0242-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Trunk Weatherstrip
p/n: 70-0773-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk directly to the body.
Fender Skirt Weatherstrip
p/n: 20-0069-44
This Fender Skirt Weatherstrip pair is designed from the original part for superior fitment and seal. This Left and Right edge weatherstrip fits between the rear fender bodywork and the removable fender skirt.
Fender Skirt Edge Weatherstrips
p/n: 20-0061-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment and seal. This weatherstrip fits between the rear quarter panel wheel opening and the fender skirt.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Hood to Cowl Weatherstrip
p/n: 70-1446-43
Weatherstrip, hood to cowl seal. Approximately fifty seven (57) inches of extruded rubber.
Outer Fender To Inner Fender Gaskets
p/n: 70-4797-45
This Outer Fender To Inner Fender Gasket pair is designed from the original part for superior fitment and seal. Gaskets fit at the top of the left and right front fenders. Gasket pieces are die-cut from quality masticated rubber to authentic original OEM dimensions.
Trunk Weatherstrip
p/n: 70-0774-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Steering Column Connecting Rod Seal
p/n: 60-0400-36
Steering column steering connecting rod seal. Power steering models require one (1) per car. Non-power steering models require two (2) per car.
Brake and Clutch Pedal Pad
p/n: 60-0218-22
Pad, brake and clutch pedal. Length: 3.75 inches. Width: 2.375 inches.
Front Stabilizer Bar End Link Set
p/n: 70-2110-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.
Radiator Upper Support Filler
p/n: 70-2502-45
This single piece Radiator Upper Support Filler is designed from the original part for superior fitment and function. Filler piece is die cut from quality masticated rubber to authentic original dimensions. Fits at radiator to radiator upper support.
Taillight Lens and Housing Gaskets
p/n: 70-4912-15
This Taillight Lens and Housing Gasket set is designed from the original part for superior fitment and seal. Includes gaskets for Lens to Housing (2) and Housing to Body (2).
Trunk Bumpers - Convertible
p/n: 70-4663-87
This Trunk Bumper pair is a quality reproduction of the original factory part. This rubber bumper attaches to the trunk decklid to support / cushion the trunk lid closure onto the vehicle body.
Hood To Fender Bumper Set
p/n: 70-3022-42
This four (4) piece Hood to Fender Bumper Set is a quality reproduction of the original factory part. This rubber bumper attaches to the hood to support / cushion the hood closure.
Gearshift Boot
p/n: 70-2285-26
Boot, transmission control shift lever. Fully molded out of black rubber instead of original white rubber, though it could be painted like original. For vehicles with Hydra-Matic column shift
Vent Window Division Post Weatherstrips
p/n: 20-0710-56
Front Vent Window Division Post seal pair that functions as the back edge of the vent window seal. Fully molded rubber over a metal core and attaching tabs.
Front Stabilizer Bar End Link Set
p/n: 70-2109-33
A twenty-two (22) piece Front Stabilizer Bar End Link set. Comes complete with fasteners, metal sleeves, metal cup washers and black rubber bushings. One (1) end link set for both sides of stabilizer bar on one (1) car.
Steering Column Tube To Floor Gasket
p/n: 20-1531-88
This Steering Column Tube To Floor Gasket is designed from the original part for superior fitment and sealing. This part fits around the steering column to seal the column tube through the body floor pan.
Firewall Grommet
p/n: 25-0099-20
This Firewall Grommet is used to run accessory wiring through the firewall. Designed from the original part for superior fit and seal.
Door Handle Gasket Set
p/n: 70-3036-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. One (1) gasket set will do either front or rear two (2) doors.
Radiator Mounting Pad
p/n: 70-0963-31
Radiator mounting pad, insulator. Up to four (4) used per car.Length: 6.0 inches.
Hood To Cowl Bumpers
p/n: 70-4744-42
This Hood To Cowl Bumper pair is a quality reproduction of the original factory part. This rubber bumper pair attaches to the body cowl to support / cushion the hood closure.
Radiator Mounting Pad
p/n: 25-0087-31
Insulator, radiator support. Two (2) to four (4) used per car.Length: 6.75 inches.
Radiator bracket cushion
p/n: 70-2015-31
Insulator, radiator support cushion, upper or lower. Fully molded with retaining carrots.
Clutch or Brake Pedal Pad
p/n: 60-0467-22
This reproduction Clutch or Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Hood Bumper Set
p/n: 20-0683-42
This six (6) piece Hood Bumper set is designed from the original parts for superior fitment and function. The set fits Ford F-Series Trucks.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Hood to Cowl Weatherstrip
p/n: 20-1311-42
Kit, cowl lacing. his seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Brake and Clutch Pedal Pads
p/n: 70-3003-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A square style direct fit reproduction to replace worn original pedal pads. Manufactured in black rubber.
Brake and Clutch Pedal Pad
p/n: 40-0287-22
Pads, brake and clutch pedal. Length: 3.625 inches. Width: 2.0 inches.
Front Engine Mount
p/n: 20-0594-11
This Front Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Window Locking Strip - Black
p/n: 70-2195-52
This extruded Locking Strip is used to retain windshield gaskets in pickups and vans. Designed from the original part for superior fitment, finish and function. Available in 16ft lengths.
Door Bumper
p/n: 70-3035-71
This Door Bumper is designed from the original part and attaches to door with single screw. Typically requires two (2) or four (4) bumpers per vehicle depending on the vehicles year of manufacture.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Body Mounting Pad
p/n: 27-0101-48
Pad, body mounting cushion. Metal core and locating collar covered with rubber.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Air Vent Gasket Set
p/n: 70-4472-31
This Air Vent Gasket set is designed from original parts for superior fitment and sealing. These quality manufactured gaskets fit to seal the two (2) conditioned air assemblies for interior comfort.
Upper Engine Mount
p/n: 20-0598-11
This Upper Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Lower Engine Mount
p/n: 20-0597-11
This Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Door Handle Gasket Set
p/n: 70-0925-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Body Mounting Pad
p/n: 70-1749-48
This Body Mounting Pad is fully molded rubber with a metal core and locating collar. These frame pads are installed between the frame and the floor pans.
Front Lower Engine Mount
p/n: 20-0596-11
This Front Lower Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation.
Door Handle Gasket Set
p/n: 70-0771-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
1-7/16" Firewall Grommet
p/n: 60-0276-45
This Firewall Grommet is used to run the throttle rod and tube, oil pressure gauge pipe, heat indicator tube, and choke rod through the firewall.
Header Bow Weatherstrip - Hardtop
p/n: 70-3918-64
This Header Bow Weatherstrip is the top and front seal rubber across windshield header for removable hardtops. Fully molded with the proper, as original, cross section in top quality rubber.
Fuel Filler Neck Grommet
p/n: 70-1439-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body. Fits as original.
Radiator top seal
p/n: 20-0130-31
Seal, radiator support top to hood. Includes special plastic buttons to install. For models with A/C.
Tailgate weatherstrip
p/n: 20-1526-87
Weatherstrip, tailgate lower glass sash channel. Goes between glass and channel.
Body Mounting Pad
p/n: 50-0506-48
Pad, body mounting. Rubber with metal core, locating collar and metal sleeve as original. Metal sleeve is removable.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Trunk Weatherstrip
p/n: 70-3923-84
This Trunk Weatherstrip is made from top quality rubber to ensure durability and designed from the original part for a superior fitment and seal. The seal mounts around the full perimeter of the trunk and directly to the body.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Taillight Lens Gaskets
p/n: 70-3775-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between taillight lens & taillight housing.
Radiator Support To Hood Weatherstrip
p/n: 20-1452-42
This Radiator Support To Hood Weatherstrip is designed from the original part for superior fitment and seal. Includes staples to install. This weatherstrip works to seal the hood to the radiator support for better engine cooling.
Hood Bumper
p/n: 20-0014-42
Bumpers, hood front to radiator support. Five sixteenths (5/16) inch by twenty four (24) thread.
Spring Clamp Liner Set
p/n: 20-1272-32
Six (6) piece Spring Clamp Liner Set. The front spring takes eight pieces for both sides and the rear spring takes four pieces for both sides.
Splash Apron / A-Arm Dust Shield
p/n: 70-2801-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Radiator Side Seals
p/n: 70-3990-31
This Radiator Side Seal pair is designed from the original part for superior fitment and function. Left and Right seals are die cut from quality masticated rubber to authentic original dimensions.
Rear Upper Engine Mount
p/n: 60-0463-11
This Rear Upper Engine Mount is designed from original part for correct fitment and function. Made of a high-quality EPDM dense rubber for durability and proper engine vibration isolation.
Steering Column To Floor Seal
p/n: 20-0674-36
This Steering Column To Floor Seal is designed from the original part for superior fitment and sealing. Seal part is die cut from quality rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Taillight Assembly Mounting Pads
p/n: 70-3777-15
This Taillight Assembly Mounting Pad pair is designed from the original part for superior fitment and seal. These reproduction gaskets fit between the taillight assembly and the vehicle body.
Front Suspension Bumper
p/n: 20-0034-32
Bumper, front suspension upper arm. Three eighths (3/8) inch by three fourths (3/4) inch bolt, twenty four (24) threads.
Cowl Vent Gasket
p/n: 60-0601-54
Side cowl vent seal. One eighth (1/8) inch thick high quality sponge design.Length: 8.50 inches. Width: 5.375 inches.
Directional or Back Up Light Lens Gaskets
p/n: 70-3776-16
This Directional Turn Signal or Back Up Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Light Lens and the Light Housing or Bezel.
Body Mounting Pad
p/n: 70-2165-48
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. Used on the bottom of most mounting locations.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Decklid Top Cover Weatherstrip
p/n: 70-3922-67
This Decklid Top Cover Weatherstrip is designed from the original part for a superior fitment and seal. This seal mounts around the full perimeter of the soft top storage compartment.
Taillight Lens Gaskets
p/n: 70-3235-15
This Taillight Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between taillight lens & taillight housing.
Directional and Parking Light Lens Gaskets
p/n: 70-3115-16
This Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Rear Seat Back Finish Panel to Package Tray Weatherstrip
p/n: 70-4096-87
This Rear Seat Back Finish Panel To Package Tray Weatherstrip mounts directly to the body to seal the Rear Seat Back Finish Panel to the Package Tray.
Rear Bumper Trim Welts
p/n: 70-4092-45
This pair of Quarter Panel to Rear Bumper End Trim Welts are designed from the originals for superior fitment and seal. These welt strips mount to the rear quarter panel bumper end piece, with one per vehicle side.
Window Stop Stem Bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Door Handle Gasket Set
p/n: 50-0560-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do two (2) doors.
Hood to Cowl Weatherstrip
p/n: 70-3959-43
This Hood To Cowl Weatherstrip has the proper rubber cross section and made from top quality rubber to ensure durability. Designed from the original part for a superior fitment and seal.
Hood Bumper
p/n: 70-0770-42
Bumper, fender to hood. Correct detail with ridges as original. Four (4) required per car.Length: 1.3125 inches.
Window Regulator | Accelerator Rod Seal
p/n: 60-0652-70
This Window Regular | Accelerator Rod Seal is used as a front window regulator seal for 1955-60 passenger cars with electric windows and for 1957-62 Corvette models. Used as an accelerator rod through toeboard seal for 1955-62 V8 only Corvettes.
Glovebox Door Check Grommet
p/n: 27-0105-88
This Glovebox Door Check Grommet is manufactured out of 100% EPDM dense rubber for durability. Designed from original for a proper fit.