Splash Apron / A-Arm Dust Shield
p/n: 70-3064-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Cowl Vent Gasket
p/n: 20-0556-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. Manufactured to OEM specifications to install for an authentic fit and finish.
Stabilizer bushing
p/n: 20-1295-33
Bushings, stabilizer bar to frame. One (1) pair required per car.
Hood Bumper Set
p/n: 20-0545-42
This six (6) piece Hood Bumper set is designed from the original parts for superior fitment and function. This set fits F Series Trucks.
Steering Column Floorplate
p/n: 20-1694-88
Seal, steering column tube. Installs on top of floor mat.
Rocker Panel Inner Drain Cover
p/n: 70-2392-45
This Rocker Panel Inner Drain Cover pair is designed from the original part for superior fitment and seal. Fully molded with proper attaching teeth and flap.
Hydraulic Pump Mounting Pad
p/n: 70-1610-67
Cushion mount, hydraulic pump.Width: .6875 inches. Height: 1.0 inches.
Firewall to Hood Weatherstrip - Cowl Lacing
p/n: 20-3006-43
This Firewall to Hood Weatherstrip - Cowl Lacing is designed from the original part for superior fitment and seal. This seal mounts with installation tacks at the rear of the engine bay firewall directly to the body.
Steering Column Floorplate
p/n: 20-3158-88
Seal, steering column to floor. Installs under floor mat.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Rear Bumper End Fillers
p/n: 70-3774-30
This two (2) piece Rear Bumper End Filler pair is designed from the original part for a superior fitment level. These die cut masticated rubber pieces fit to the left and right bumper ends between the rear bumper and the vehicle body.
Brake Master Cylinder Push Rod Boot
p/n: 60-0180-24
This Brake Master Cylinder Push Rod Boot is made from high-quality Nitrile rubber for a precise, factory like fit for your classic vehicle. Manufactured to OEM specifications to install for an authentic fit and finish.
Stabilizer Bar End Link Set
p/n: 60-0221-33
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt 3/8"-16 NF x 6-15/16" long. Comes with metal sleeve, metal cup washers and rubber grommets.
Battery Hole Cover Seal
p/n: 20-0555-21
This Battery Hole Cover Seal is designed from the original part for superior fitment and seal. This part seals the battery hole cover to the vehicle floor.
Firewall Grommet
p/n: 70-2066-24
This Firewall Grommet is used to run the emergency brake cable through the firewall. Designed from the original part for superior fit and seal.
Starter Button Cover
p/n: 60-0166-21
Cover, starter pedal button. Rubber slip over type for old metal. Two (2) inch outside diameter. If car doesn't have old metal, see our #60-0322-21.
Vent Window Division Bar Weatherstrip
p/n: 70-1432-56
This Front Vent Window Division Bar Weatherstrip is designed from the original part for superior fitment and seal. A single 32" inch (approximate) length of original cross-section extruded rubber.
Body Mounting Pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar.
1-7/16" Firewall Grommet
p/n: 60-0276-45
This Firewall Grommet is used to run the throttle rod and tube, oil pressure gauge pipe, heat indicator tube, and choke rod through the firewall.
Body Mounting Pad
p/n: 70-1429-48
Pad, body mounting. Fully molded rubber with metal core and rubber locating collar. Also used for radiator cradle to frame. Eight (8) to ten (10) required per car. Two and one fourth inch (2 1/4") outside diameter by one and one sixteenth inch (1 1/16") l
Hood Bumper Set
p/n: 33-0680-42
This eight (8) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Lower Rear Engine Mount
p/n: 20-0584-11
This Lower Rear Engine Mount is designed from original part for correct fitment and function. Made of a quality dense rubber for durability and proper engine vibration isolation. Two (2) required per truck.
Firewall Grommet
p/n: 70-2067-20
This Firewall Grommet is used to run the main wiring harness through the firewall. Designed from the original part for superior fit and seal.
Body Mount Isolator Pad
p/n: 70-0929-48
Body Mount Isolator Pad - Rubber with metal core and locating collar as original part. Part dimensions = Two and three sixteenths inch (2 3/16") square by one inch (1") overall height with thirteen sixteenths inch (13/16") inside bolt diameter. Does not include any fastener hardware.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Body Mounting Pad
p/n: 27-0092-48
Insulator, body mounting pad. Metal core & locating collar covered with rubber.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Rear Leaf Spring Insulator
p/n: 70-0980-32
This Rear Leaf Spring Insulator is an exact replacement for the upper and lower spring pad. Two and one half (2-1/2) inches wide, with cloth reinforcement. Four (4) used per car.
Brake and Clutch Pedal Pads
p/n: 60-0300-22
Pad, brake and clutch pedal.Length: 3.0 inches. Width: 2.5625 inches.
Lock Pillar Water Deflector
p/n: 70-3635-62
Door panel water deflector, at lock. Fully molded for both left and right hand sides.