Steel Sash Channel - Left Front Door
p/n: 20-3047-58
This reproduction Steel Sash Channel is designed from the original part for superior fitment and function. This channel is for the Driver (Left) Side Front Door.
Side Window Vent Frame Upper Bumpers
p/n: 60-0183-62
These Side Window Vent Frame Upper Bumpers (pair) are designed from the original part for superior fitment and function. This glass bumper fits in vent frame at the top on the right and left sides of the vehicle.
Steel Sash Channel - Right Front Door
p/n: 20-3046-58
This reproduction Steel Sash Channel is designed from the original part for superior fitment and function. This channel is for the Passenger (Right) Side Front Door.
Rear Window Gasket
p/n: 20-0571-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Front Engine Mount
p/n: 20-1786-11
This Front Engine Mount is made of a quality rubber over a metal core to provide maximum life and performance. Two (2) required per car.
Headliner Retainer Strip
p/n: 60-0368-88
Retainer strip. Holds cardboard headliner in place. Twelve (12) foot strip.Length: 144.0 inches. Width: .5625 inches.
Air Conditioning Pipe Grommet
p/n: 70-0934-31
Grommet, air conditioning pipes to compressor and condenser. One (1) per car.Length: 4.375 inches. Width: 2.5 inches.
Fuel Filler Neck Lower Cover Collar Seal
p/n: 70-3700-39
This Fuel Filler Neck Lower Cover seals the neck where it goes through rear fender splash panel on the trunk floor. Part is fully molded rubber with a corrosion resistant brass core.
Rear coil spring pad
p/n: 50-0359-35
Insulators, rear coil spring. Fabric reinforced rubber as original. One (1) pair per car.
Beltline Weatherstrip
p/n: 30-0300-58
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with stainless bead. Available in 3ft pair.
Flexible Run Channel
p/n: 20-1146-58
This Flexible Run Channel helps to eliminate window rattle, provides a smooth sliding surface for glass movement, and works to protect the glass. Stainless steel beaded. Available in sixty (60) inch strips.
Windshield Weatherstrip Set
p/n: 70-3915-50
This four (4) piece Windshield Weatherstrip Set works to install the Corvette windshield with a precise, like factory fit. Parts are designed from originals to fit correctly.
Door Auxiliary Weatherstrips
p/n: 60-0342-73
This six (6) piece Door Auxiliary Weatherstrip set is designed from the original part for superior fitment and seal. The Auxiliary Weatherstrip, also known as a "J" seal, installs on the door front at the beltline, right and left sides of the vehicle.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Flexible Run Channel - 60 Inch
p/n: 20-1619-58
Channel, side window glass, vertical run. Flexible, felt lined, rubber covered channel. Available 60" lengths.
Window Felt Beltline Weatherstrips
p/n: 80-0631-57
Made from Original style material. Side window horizontal seal (also known as beltline weatherstrip). These strips wipe the side windows when the glass is lowered.
Door Glass Run Channel
p/n: 20-0531-58
A top-quality Door Glass Run Channel with stainless beaded edge. Includes pre-installed clips. Enough for one door only.
Rear Bumper To Body Filler
p/n: 60-0359-30
This dense rubber Rear Bumper To Body Filler is designed from the original part for a superior fitment. The part is approximately sixty-six (66) inches long and fits between the vehicle body and the rear bumper.
Body Bumper Kit
p/n: 90-0205-90
This fourteen (14) piece Body Bumper Kit is designed from the original part for superior fitment, finish and function. Designed from originals and made from top quality rubber to ensure durability.
1935-1974 Cadillac Factory Parts Manual, CD
p/n: 07-1346-07
This GM Licensed Detroit Iron CD provides the most comprehensive set of digital Cadillac Factory parts manuals. The factory manuals on this CD were professionally scanned from the original service and parts manuals.
Tailgate or Back Door Weatherstrip
p/n: 70-3604-84
This Tailgate or Back Door Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts with properly spaced plastic clips around the full perimeter of the rear opening.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Front coil spring pad
p/n: 70-2302-35
Pad, front coil spring insulator cushion. Fully molded, mounts at top of front coil springs.
Vent Window Division Bar Weatherstrip
p/n: 30-0541-74
Division post seal pair for rear door vent window. Made from top quality rubber to ensure durability and proper seal. Designed from original part so it fits correctly.
Vent Division Bar Assembly
p/n: 20-0532-56
Assembly, complete division bar. Right-side only. Ready to install. Comes complete with brackets and back of vent window seal.
Vent Division Bar Assembly
p/n: 20-0533-56
Assembly, complete division bar. Left-side only. Ready to install. Comes complete with brackets and back of vent window seal.
Quarter Window Filler
p/n: 20-3085-62
Seal assembly. Installs on body below rear quarter glass to body weatherstrip.
Clutch and Brake Pedal Pads
p/n: 60-0068-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. An oval style perfect reproduction to replace worn or damaged original pedal pads.
Front Spring Rubber Bumpers
p/n: 70-0329-32
This Front Spring Rubber Bumper Pair fits to the upper control arms on frame. Manufactured to OEM specifications to install for an authentic fit, finish and function.
Front Door Auxiliary Weatherstrips
p/n: 70-0551-73
This Front Door Auxiliary Weatherstrip pair fits to the left and right doors at the beltline. Uses snap-in fasteners, four (4) each included.
Vent division bar weatherstrip
p/n: 70-1511-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Rear Window Gasket Set
p/n: 60-0082-83
This Rear Window Gasket Set contains the rear window gasket itself and the locking strip. Both strips comes in a ninety inch (90") piece and mount around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Stabilizer Bar End Link Set
p/n: 70-0567-34
Twenty-two (22) piece Stabilizer Bar End Link set for both sides of one (1) vehicle, fits front or rear bar. Order two (2) sets for vehicles with front and rear stabilizer bars. Hex head bolt. 5/16"-24NF x 7-5/8" long. Includes metal sleeves, cup washers and rubber grommets.
Quarter Window Filler
p/n: 70-3431-67
These quarter window fillers mount inside the rear panel at the bottom of the rear side window. The pair is fully molded as left and right with brass cores.
Front Stabilizer Bar Bushing
p/n: 70-1293-33
A Front Stabilizer Bar to Frame Bushing pair for both sides of the vehicle. Fits front stabilizer or sway bar. Manufactured with quality materials to original specifications. One (1) pair per vehicle.
Carpet Heel Plate
p/n: 70-3019-88
Heel pad for carpet. Seven and three eighths (7-3/8) inch wide by sixteen (16) inches long.
Front Suspension Rubber Bumper
p/n: 60-0103-32
Front Suspension Rubber Bumper for the front suspension lower control arm (attaches to lower arm spring mount). Steel core, with original size bolt. Width: 1.625 inches.
Vent division bar weatherstrip
p/n: 30-0532-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Hood to Cowl Weatherstrip
p/n: 70-0940-42
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. An exact reproduction of the original profile. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Flexible Run Channel
p/n: 60-0375-58
For windows with metal glass frames. Flexible corrugated steel, cloth covered, mohair lined. Available in 5ft lengths.
Vent Window Division Post Seals
p/n: 70-4333-56
This Front Vent Window Division Post Seal pair is designed from the original part for superior fitment and seal. Parts are fully molded EPDM rubber over a brass metal core.
Axle Rebound Pad
p/n: 30-0534-32
Bumper, rear axle rebound.Length: 3.0 inches. Width: 2.375 inches. Height: 1.6875 inches.
U Jamb Lock Pillar Filler
p/n: 60-0570-79
This U Jamb Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This part seals the bottom of the rear side window. Fully molded authentic rubber construction with metal core.
Upper Control Arm Shaft
p/n: 20-1278-32
This three (3) piece Upper Control Arm Shaft set is designed from the original part for superior fitment and performance. Renew the performance of your aged and worn front suspension to restore the ride of your classic vintage vehicle.
Rear Window Gasket
p/n: 70-2051-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Rear Vent Window Division Post Weatherstrip
p/n: 70-3762-56
This Rear Door Vent Window Division Post Weatherstrip pair is designed from the original part for superior fitment and seal. This seal is fully molded with EPDM rubber over brass metal cores. This part fits opposite the glass run channel and seals the vent window when the vent is closed.
Trunk Weatherstrip - Clipped
p/n: 70-1123-85
This Clipped Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter and directly to the trunk lid using properly spaced plastic clips.