Brake and clutch pedal pad
p/n: 11-0023-22
Pedal pad, clutch and brake. Original pattern, superior workmanship.
Brake and Clutch Pedal Pads
p/n: 40-0213-22
Pad, brake and clutch pedals. Horizontal oval style, slip over type.Length: 3.8125 inches. Width: 2.375 inches.
Brake and Clutch Pedal Pads
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Brake and Clutch Pedal Pads
p/n: 40-0072-22
Pad, brake and clutch pedal.Length: 3.9375 inches. Width: 2.9375 inches.
Brake and Clutch Pedal Pads
p/n: 40-0038-22
Pad, brake and clutch pedal. See also our #40-0072-22.Length: 3.8125 inches. Width: 2.3125 inches.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Brake and Clutch Shank Seal
p/n: 40-0016-24
Seal, brake and clutch pedal shank to floorboard (draft excluder).Length: 2.4375 inches. Width: 1.875 inches.
Brake and Clutch Shank Seal
p/n: 30-0055-24
Seals, brake and clutch pedal shanks, against underside of floorboard.Length: 2.5625 inches. Width: 1.75 inches.
Brake and clutch shank seal
p/n: 60-0019-24
Seal, brake and clutch pedal shank to floorboard. Single bellows rubber cup, seals air drafts around pedals.
Brake and Clutch Shank Seal
p/n: 40-0175-24
Seal, brake and clutch pedal shank to floorboard. One and one half (1-1/2) inch by two and one eighth (2-1/8) inch by three fourths (3/4) inch thick.
Brake Cable Anti-Rub Cover
p/n: 60-0443-24
Sleeve, rear brake cable anti-rub. Six (6) piece set. One half (1/2) inch inside diameter, seven eighth (7/8) inch outside diameter.
Brake Cable Boot
p/n: 60-0156-24
Boot, front brake cable end at brake backing plate. Two and seven eighths (2-7/8) inches long.Length: 2.875 inches.
Brake Cable Boots
p/n: 70-0067-24
This Brake Cable Boot pair is designed from the original part for superior fitment and seal. Boot fits over brake cables at front or rear wheels.
Brake Master Cylinder Filler Access Hole Cover
p/n: 60-0016-24
This Master Cylinder Access Hole Cover is designed from the original part for superior fitment and seal. Secures the Brake Master Cylinder Filler and Inspection Access Hole in the vehicle.
Brake Vacuum Cylinder Rod Boot
p/n: 70-0485-24
This Brake Vacuum Cylinder Rod Boot is designed from the original part for superior fitment and function. For piston type vacuum cylinders.
Brown Gearshift Boot
p/n: 50-0035-89
Boot, gearshift. Brown rubber. For black see our #50-0035-24.Color:brown Width: 2.8125 inches.
Brown Handbrake Floorplate
p/n: 40-0110-89
Floorplate, handbrake. Brown rubber. Steel core as original.
Brown Steering Column Cushion
p/n: 60-0012-89
Grommet, steering column to cowl, for U-bolt clamp. Brown rubber. For black see our #60-0012-36.Color:brown Height: 1.25 inches.
Brown Steering Floorplate
p/n: 50-0117-89
Floorplate at steering column and pedals. Brown rubber. Metal core as original.
Cadillac Motors pedal pad
p/n: 70-0076-22
Cadillac Motors pedal pads. Authentic straight diamond pattern. Especially good copy, fine detail.
Cadillac V-8 Pedal Pad
p/n: 70-0148-22
Cadillac V-8 pedal pads, clutch and brake. Another rare one we finally found to copy. Superior copy.
Carpet Heel Plate
p/n: 70-0617-88
Heel mat, front carpet insert.Length: 13.5625 inches. Width: 9.75 inches.
Carpet Heel Plate
p/n: 40-0087-88
Heel pad for carpet. Identical to original. Five and three fourths (5-3/4) inch by ten and one half (10-1/2) inch, to be stitched in place.Length: 10.
Channel Filler Weatherstrip
p/n: 20-2091-62
This Channel Filler Weatherstrip is designed from the original part for superior fitment and seal. This door glass to body filler seal fits in the metal channel that holds the glass piece. Sold in a 36" strips.
Choke and Throttle Dash Grommets
p/n: 20-0347-41
This Choke and Throttle Dash Grommet pair mounts in the dash where the choke and throttle rods pass through the dash to keep rods from rattling.
Choke, Throttle and Starter Wiper Motor Grommet
p/n: 20-1561-20
This Choke, Throttle or Wiper Motor Grommet is designed from the original part for superior fitment and usage. A multi-purpose grommet, it fits into the vehicles firewall to provide a secure passthrough for the mechanical choke, throttle rod or wiper motor wiring.
Chrome Fender Welting - 25ft
p/n: 70-1101-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Twenty five (25) foot roll. Typically used to attach two (2) fenders to body. For fifty (50) foot roll see our #70-1102-44.
Chrome Fender Welting - 50ft
p/n: 70-1102-44
Welting, fender, bright chrome vinyl, three sixteenths (3/16) inch bead, one and one half (1-1/2) inch width. Superior quality. Fifty (50) foot roll. Typically used to attach four (4) fenders to body. For twenty five (25) foot roll see #70-1101-44.
Clutch and Brake Pedal Pads - Black
p/n: 50-0077-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch and Brake Pedal Pads - BLACK
p/n: 25-0024-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Black rubber.
Clutch and Brake Pedal Pads - Bowtie Emblem
p/n: 60-0043-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber. Excellent detail with bowtie emblem like original.
Clutch and Brake Pedal Pads - BROWN
p/n: 25-0024-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A reproduction with authentic type ribbing, to replace worn original pedal pads. Manufactured in Brown rubber.
Clutch, Brake Pedal or Rumble Seat Pads
p/n: 20-0325-22
This reproduction Pad pair easily screws on the clutch and brake pedal arms for a precise, factory fit. Pads with pyramid design like original. Used as clutch and brake pedal pads for all models. Used as a rumble seat step pad for cars so equipped.
Coil wire sleeve
p/n: 70-0109-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only. V-12 & V-16 with coils mounted in radiator, V-8 with coils mounted horizontally on brace rods.
Coil wire sleeve
p/n: 70-1179-21
Sleeve, coil wire to distributor. Fluted to match upper water hoses rubber only.
Coil wire sleeve
p/n: 40-0336-21
Nipple, sparkplug wire at sparkplug, for right angle plug terminal. This is an exact copy of the style used at the time. Not a modernistic makeover.
Convertible A-Pillar Post Weatherstrips
p/n: 70-0072-63
This Convertible Hinge A-Pillar Weatherstrip pair attaches to the body and seals between the A-pillar windshield post and the front section of the door or vent window frame when the door is closed.
Cowl Firewall Grommet
p/n: 20-1560-20
This Cowl Firewall Grommet fits into the upper section of the firewall for the main wiring harness. Also used to run the dash wires on the firewall and through the firewall.
Cowl Vent Gasket
p/n: 20-2049-54
This Cowl Vent Gasket is designed from the original part for superior fitment and seal. This gasket works to seal the cowl vent when closed into the cowl body. Made from top quality rubber to ensure durability and proper seal.
Cowl Vent Gasket
p/n: 60-0044-54
Gasket, cowl vent. One (1) piece sponge rubber shear die cut to correct dimensions. Replaces #4034247-8.
Cowl Vent Gasket
p/n: 30-0096-54
Gasket, top cowl vent. Closed cell sponge rubber. One half (1/2) inch by three fourths (3/4) inch. Rectangular cross section.
Cowl Vent Gasket
p/n: 60-0131-54
Gasket, cowl vent. One fourth (1/4) inch by five sixteenths (5/16) inch, for five (5) inch by fifteen (15) inch top cowl vent. Sponge type.Width: 15.
Cowl Vent Gaskets
p/n: 40-0170-54
This Cowl Vent Gasket is manufactured from high quality EPDM sponge rubber. For twin cowl vents of thirty four (34") inch circumference.
Cowl Vent Weatherstrip
p/n: 50-0123-54
Weatherstrip, cowl vent lid (top), sponge lip type, for five (5) inches by eighteen (18) inches cowl vent.Width: 18.0 inches. Height: 5.0 inches.
Crankshaft Vibration Damper - Revulcanization Only
p/n: 30-0376-12
This Revulcanization Service Only is designed to restore the Crankshaft Vibration Damper to a like new original condition. This revulcanizing service is for the rubber cushion elements. Service requires your metal core.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Door Alignment Pad
p/n: 70-1821-71
Wedge pads, door aligning.Length: 1.125 inches. Width: .5 inches. Height: .875 inches.
Door and Trunk Handle Gasket
p/n: 40-0132-70
Pad, door handle escutcheon. Two and five sixteenths (2-5/16) inch by one and seven sixteenths (1-7/16) inch.
Door Bottom weatherstrip
p/n: 70-3140-73
Seal, lower door. Mounts to door scuff plates. Enough for 4 doors.
Door Bumper
p/n: 40-0037-70
Pad, door jamb. One and nine sixteenths (1-9/16) inch long by one and one eighth (1-1/8) inch wide.Length: 1.625 inches. Width: 1.0625 inches.
Door Bumper
p/n: 17-0039-71
Bumper, round door side. An auxiliary door side bumper on door jamb pad.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Door Bumper
p/n: 30-0002-71
Bumper, door side. One and one fourth (1-1/4) inch by two (2) inch.Length: 2.0 inches. Width: 1.25 inches.
Door Bumper
p/n: 17-0041-70
Pad, door jamb, large size, retained by both dovetail retainer from back, and screw through center. Usually 2 per door.Length: 2.125 inches. Width: 1.
Door Bumper
p/n: 40-0154-70
Bumper, door side. One and one fourth (1-1/4) inch long by one (1) inch wide. Similar to our #40-0010-70, but different workface.Length: 1.0 inches.
Door Bumper
p/n: 70-1155-71
Pad, door jamb (door side bumper).Length: 1.25 inches. Width: .9375 inches.
Door Bumper
p/n: 70-1156-71
Door Side Bumper made from EPDM Dense rubber. Clip retained. Appears identical to Atwood #107, #208. Width: 1-1/2" inches. Height: 1-5/16"
Door Bumper
p/n: 60-0581-71
Pad, door jamb. (Door side bumper). Two screw type with metal reinforcing inserts.
Door Bumper
p/n: 30-0052-71
Bumper, door side, upper. Oblong type, perfect copy of original.Length: 2.4375 inches.
Door Bumper
p/n: 40-0316-70
Bumper, door side, lower, on lock post. Retained by dovetail tapping plate.Length: 1.5625 inches. Width: 1.5625 inches.
Door Bumper
p/n: 30-0032-71
Pad, for door. Circular shape, one and one fourth (1-1/4) inch diameter.
Door Bumper
p/n: 40-0010-70
Pad, door jamb, fully detailed. One and one eighth (1-1/8) inch long, one and one fourth (1-1/4) inch wide.Length: 1.125 inches. Width: 1.25 inches.