Turn signal light gasket
p/n: 20-0749-16
Gaskets, side marker light. Front and rear. Four (4) piece set.
Brake or Clutch Pedal Pad - Manual
p/n: 60-0709-22
A top-quality rubber Clutch or Brake Pedal Pedal Pad reproduction. One (1) each slip-over type pedal pad installs over the full perimeter of the brake or clutch pedal for a precise, factory fit. For manual transmission model GM vehicles only.
Stabilizer Bar Bushings
p/n: 70-4678-34
This Stabilizer Bar to Frame Bushing pair may fit either front or rear stabilizer / sway bars depending on the vehicle. Manufactured with quality materials to original specifications.
Hood to Cowl Weatherstrip
p/n: 70-2807-43
This Hood to Cowl Weatherstrip is designed from the original part for superior fitment and seal. This seal mounts at the rear of the engine bay directly to the body.
Splash Apron / A-Arm Dust Shield
p/n: 70-3316-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Pieces fit over suspension a-arms and inside front inner fenders.
Parking Brake Cable To Floor Seal
p/n: 20-0760-24
This Parking Brake Cable To Floor Seal is designed from the original part for superior fitment, finish and function. The part protects the parking brake cable as it passes through the truck body floor pan.
Trunk Decklid Bumper Stop
p/n: 82-0160-87
This Trunk-Decklid Bumper Stop is a quality reproduction of the original factory part. This adjustable rubber bumper attaches to the vehicle body to support / cushion the trunk lid closure.
Door Glass Run Channel
p/n: 70-4313-58
This Door Glass Run Channel is designed from the original part for superior fitment and seal. The window glass run channel presses into the door channel at the top and back part of the door. This single piece fits either the driver (LH) OR the passenger (RH) side front door.
Body Mounting Pad
p/n: 70-2165-48
Pad, body mount, lower bolt retaining. Rubber with metal washer molded in. Used on the bottom of most mounting locations.
Vent Window Rebuild Set
p/n: 70-4801-70
This Vent Window Rebuild Set includes glass setting tape (1/16 thick), hinge pivot step rivet pair, and a rivet peening punch. The set has enough materials for both the passenger side and driver side vent window assemblies.
Firewall To Hood Weatherstrip - Cowl Lacing
p/n: 70-4014-42
This Firewall To Hood Weatherstrip - Cowl Lacing comes with pre-drilled mounting holes and mounting clips installed. Made of high-quality EPDM rubber and to the original design for a factory like fit and appearance.
Radius Arm Bushing
p/n: 20-0671-36
This Radius Arm Bushing is a quality reproduction of the original factory part. The bushing fits at the frame end of the radius rod on 4-Wheel Drive models. Requires two (2) bushings per side with four (4) total per vehicle.
F-100 Brake Pedal Pad, Automatic
p/n: 70-4485-22
This reproduction F-100 Brake Pedal Pad slips over the full perimeter of the brake or clutch pedal for a precise, factory fit. Replaces original brake pedal pads for automatic transmissions.
Side Window Glass Run Channel
p/n: 20-0812-58
This Side Window Glass Run Channel is designed from the original part for superior fitment and seal. Single length of flexible window run channel for the sides and top of door windows. For Left or Right side, order two (2) per truck as needed.
Brake Pedal Pad - Automatic
p/n: 60-0710-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. A direct fit to replace worn, heavy wear original brake pedal pads. For GM models with an automatic transmission.
Rear Hatchback Door Window Glass Weatherstrip
p/n: 70-4826-81
This Rear Hatchback Door Window Glass Weatherstrip is designed from the original part for superior fitment and seal. A reproduction of edge channel that surrounds the metal edge were the rear hatch window glass touches the hatch door.
Radiator Insulator Pads - Set of 4
p/n: 20-0198-31
This Radiator Insulator Pad set is designed from the original part for superior fitment and function. Molded insulator pads; two (2) long and two (2) short pads for the upper and lower, and for the left and right sides of the radiator. For various applications.
Taillight Lens Gasket
p/n: 20-0746-15
Gaskets, taillight lens. Rectangular type. Style-side pickups before Serial # T00,001.
Clutch Pedal Rod Boot
p/n: 20-1049-23
This Clutch Pedal Rod Boot is designed from the original part for superior fitment and seal. Accordion style boot seals the clutch rod to the floor.
F-100 Brake OR Clutch Pedal Pad
p/n: 70-4484-22
This reproduction F-100 script Brake OR Clutch Pedal Pad slips over the full perimeter of the brake or clutch pedal for a precise, factory fit. Replaces original brake or manual transmission clutch pedal pads.
Hood to Fender Bumper Set
p/n: 20-0213-42
This Hood to Fender Bumper Set is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Steering Column - Floor Seal
p/n: 70-3358-36
This Steering Column is designed from the original part for superior fitment and sealing. Seal part is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan inside the vehicle.
Clutch or Brake Pedal Pad
p/n: 20-0848-22
This reproduction Clutch and/or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
2-7/16" Floor Plug
p/n: 35-3508-45
This Floor Plug is fully molded and designed from the original part for superior fitment and seal. This plug is made from high-quality EPDM dense rubber to provide excellent durability. Up to ten (10) used per vehicle.
Adjustable Hood Bumper
p/n: 70-1084-42
This Adjustable Hood Bumper is designed from the original part for superior fitment, finish and function. Adjustable with molded on rubber cap.
Adjustable Hood Bumper
p/n: 70-2715-42
This Radiator Support to Hood Bumper is a quality replacement for the original factory part. This adjustable bumper attaches to the radiator support to cushion / stop the hood closure. Usually requires two (2) front bumpers each per vehicle.
Body Hole Plug
p/n: 20-0764-24
Plug, fill hole. Used where clutch rod goes on standard transmission.
Tailgate Bumper
p/n: 20-0694-45
These Tailgate Bumpers are sold as pair. The bumpers fit in brackets and comes with chains.
Door Handle Gasket Set
p/n: 70-1647-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do two (2) doors.
Tailgate Lower Seal
p/n: 70-4010-85
This Tailgate Lower Seal is properly molded from originals for a factory like fit. The seal is installed using screws, which are included.
Tailgate Bumper
p/n: 20-0801-45
This Tailgate Bumper is used as a retaining support. Two (2) are required per truck.
Trunk Emblem Gasket
p/n: 70-3220-87
This single Trunk Emblem gasket is designed from the original part for superior fitment and seal. The gasket is precision die cut to the original specifications. This gasket is for one (1) trunk / decklid emblem mounting.
Windshield Frame Lower Weatherstrip
p/n: 70-4477-52
This Windshield Frame To Body Lower Weatherstrip is designed from the original part for superior fitment and sealing. This is the lower windshield frame hinge weatherstrip. It mounts to seal between the windshield frame and the cowl with the bead facing to the inside of the vehicle.
Bronco Script Brake OR Clutch Pedal Pad
p/n: 70-4480-22
This reproduction Brake OR Clutch Pedal Pad slips over the full perimeter of the brake or clutch pedals for a precise, factory fit. Replaces original brake or manual transmission clutch pedal pads.
Windshield Molding Joint Cover With Wide Moldings
p/n: 70-4483-52
This Windshield Molding Joint Cover is designed from the original part for superior fitment and usage. This cover is made from Stainless Steel to cover the molding joint where the Windshield rubber comes together.
Hood bumper
p/n: 70-2871-42
Bumper, hood, front adjustable. Bumper threads into radiator support on left and right side. Two (2) required per car.
Instrument Panel Grommet
p/n: 70-1654-88
Grommet, instrument panel to windshield frame. Two (2) to six (6) required.Length: 1.3125 inches. Width: 1.0625 inches.
Headlight dimmer switch pad
p/n: 70-0930-14
Pad, headlight dimmer switch. Rubber slip-over cover for floor mounted switch.
Multi-Purpose Clips
p/n: 70-4802-45
A ten (10) piece set of Multi-Purpose Clips. Commonly used to retain Hood to Cowl Weatherstrips or Inner Fender Splash Panels.
Parking Brake Pedal Pad
p/n: 70-4804-22
This reproduction Parking Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace a worn or damaged original pedal pad.
Parking Light Lens Gaskets
p/n: 20-2683-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Lens and the Parking Light Housing or Bezel.
Parking Light Housing Gaskets
p/n: 20-0612-16
This Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Parking Light Housing or Bezel and the body of the vehicle.
Steering Column At Floor Seal
p/n: 70-3490-36
This Steering Column At Floor Seal is designed from the original part for superior fitment and sealing. The seal is die cut from quality masticated rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Glovebox Link Bumper
p/n: 50-0367-88
This Glovebox Link Bumper is made to original specifications for an authentic fit and appearance. The glovebox check link bumper fits on the glovebox door arm.
Taillight Mounting Pad
p/n: 70-3564-15
Gasket, taillight mounting pad. Eight (8) used per car. Machine die cut 5/8" thick sponge rubber seals tail light assembly to body. Included in our kit part number #70-3566-15.