Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Clutch and Brake Pedal Pads - Brown
p/n: 50-0054-89
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality brown rubber.
Clutch or Brake Pedal Bumper
p/n: 20-1051-24
This Clutch or Brake Pedal Bumper is designed from the original part for superior fitment, finish and function. This bumper is commonly used as a clutch or brake pedal arm stop cushion.
Clutch or Brake Pedal Pad
p/n: 20-0848-22
This reproduction Clutch and/or Brake Pedal Pad slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Control Arm Bumper
p/n: 40-0465-32
Bumper, upper control arm. One (1) pair per car.Height: 1.375 inches.
Control arm bushing
p/n: 20-1280-32
Bushing, control arm. Upper inner rear. One (1) required per side.
Control arm bushing
p/n: 20-1293-32
Bushing, control arm. Upper inner front. One (1) required per side.
Control arm bushing seal
p/n: 60-0094-32
Seal, upper and lower control arm cross shaft bushing, at inner end of arm.1939-48: Lower only, all pass. (exc.
Control Arm Bushing Seal
p/n: 60-0095-32
Seal, lower control arm pivot bolt bushing. Four (4) per car.Width: .1875 inches.
Convertible A-Pillar Post Weatherstrips
p/n: 20-1912-63
This Convertible A-Pillar Post Weatherstrip pair is designed from the original part for superior fitment and sealing.. These windshield post weatherstrips attach to the body to seal between the A-pillar post and the front section of the door or vent window frame when the door is closed.
Convertible Front Bow Weatherstrip
p/n: 60-0253-64
This Convertible Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This header seal installs directly to the windshield frame to seal between the soft top and the rear center section.
Convertible Roof Rail Bumper
p/n: 20-1920-67
Bumpers, roof assembly to quarter panel. Four (4) piece set.
Convertible Roof Rail Weatherstrip Set
p/n: 70-0757-65
This Convertible Roof Rail Weatherstrip Set fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
Convertible Roof Rail Weatherstrip Set
p/n: 20-1762-65
This seven (7) piece Convertible Roof Rail Weatherstrip set fits on the folding roof of the vehicle and seals the side windows when the windows are fully raised. Cloth covered like original. The set also includes the front header bow weatherstrip.
Convertible Roof Rail Weatherstrip Set
p/n: 60-0140-65
This ten (10) piece reproduction Convertible Roof Rail Weatherstrip Set is designed from the original part. These high-quality rubber weatherstrips fit on the roof of the vehicle and work to seal the side windows when the window is fully raised. Set includes the front header bow weatherstrip.
Convertible Roof Rail Weatherstrip Set
p/n: 50-0437-65
This Convertible Roof Rail Weatherstrip Set fits on the folding roof of the vehicle and seals the side window when the window is fully raised.
Convertible Roof Rail Weatherstrip T-Bolt Set
p/n: 70-4606-67
These Convertible Top Roof Rail Weatherstrip T-Bolt reproductions are designed from the original part for superior fitment and function. This twenty two (22) t-bolts and twenty two (22) nut set fastens to the convertible top bow weatherstrips.
Convertible Top Rest Block
p/n: 60-0209-67
These Convertible Top Rest Blocks are used on the folding top, side roof rail slat iron. Fully molded with a brass core as original. Sold as a pair. Two (2) or four (4) per car as required for front and center.
Cowl Drain Gutter Hose Grommet
p/n: 33-0329-54
This Cowl Drain Gutter Hose Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Cowl Side Ventilator Door Gasket
p/n: 20-1327-54
This Cowl Side Ventilator Door Gasket is molded as the Original. Two (2) required per car.
Cowl Top Plug
p/n: 20-1813-20
This Cowl Top Plug is designed from the original part for an authentic fit, finish, and appearance. This plug installs in the access hole in cowl top.
Cowl Vent Weatherstrip
p/n: 20-0705-54
This six (6) piece Cowl Vent Weatherstrip is used to reduce noise from the cowl vent screen. These U-Shaped stripes are designed for a superior fitment and seal.
Cowl Ventilator Grille Weatherstrips
p/n: 20-1886-54
These Cowl Ventilator Grille Weatherstrips are used to reduce noise from the cowl top ventilator grille. These U-Shaped stripes are designed for a superior fitment and seal.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Directional and Parking Light Lens Gaskets
p/n: 70-3116-16
This Turn Signal and Parking Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Signal / Parking Light Lens and the Signal / Parking Light Housing or Bezel.
Division Bar Channel and Beltline Set
p/n: 80-0016-57
This is an Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This ten (10) piece set includes vent window division bars inner / outer window felt beltline weatherstrips for each side window and quarter window and a felt piece for above the rear quarters.
Division Bar Channels and Window Felt Beltlines Set
p/n: 80-0014-57
This is an Original equipment style side window horizontal weatherstrip set (also known as beltline weatherstrip). This ten (10) piece set includes vent window division bars inner / outer window felt beltline weatherstrips for each side window and quarter window and a felt piece for above the rear quarters.
Door - Gravel Shield - Running Board Weatherstrip
p/n: 60-0054-73
This Door - Gravel Shield - Running Board Weatherstrip is a anti-squeak bulb type extrusion with fitment for General Motors vehicles. A twelve (12) foot strip made of high-quality EPDM dense rubber and designed from original parts for superior fitment, finish and function.
Door Auxiliary Weatherstrips
p/n: 60-0342-73
This six (6) piece Door Auxiliary Weatherstrip set is designed from the original part for superior fitment and seal. The Auxiliary Weatherstrip, also known as a "J" seal, installs on the door front at the beltline, right and left sides of the vehicle.
Door Bumper
p/n: 70-2365-71
Bumpers, rear door opening. Proper configuration with slots for retaining screws like original.
Door Bumper
p/n: 60-0334-71
Bumper, back door check link above door. Dovetail base fits check arm.Length: 1.0 inches. Width: 1.0 inches. Height: .625 inches.
Door Bumper
p/n: 70-2615-71
This fully molded 5/8" Door Bumper is quality reproduction of the original factory part. This twin retainer style rubber bumper attaches to the vehicle body to support / cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door Bumper
p/n: 34-0131-37
Bumper, front door above the upper hinge on the upper radius of the door. Stiff-backed, retained by screw, mounted on door only.
Door Bumper
p/n: 50-0203-41
This Door Bumper is used for the fuel filler door on the rear fender. Molded from top-quality EPDM rubber over a steel core for durability. These bumpers are screw retained.
Door Bumper
p/n: 33-1234-71
This Door Bumper is fully molded and designed from the original part for superior fitment. This door bumper attaches to the vehicle door to support/cushion the door closure. Two (2) or four (4) used per car.
Door Bumper
p/n: 33-1227-71
This Door Bumper is fully molded and designed from the original part for superior fitment. The twin retainer style rubber bumper attaches to the vehicle body to support/cushion the door closure. Usually requires two (2) bumpers each per vehicle.
Door Drain Hole Seal
p/n: 60-0442-70
This Door Drain Hole Seal installs on the door bottom and is also used on the tailgate of station wagons. Two (2) required per vehicle. Molded from high-quality EPDM dense rubber.
Door Edge Weatherstrips
p/n: 60-0247-72
This Door Edge Weatherstrip pair is designed from the original parts for superior fitment and seal to keep the elements out and reduce road noise while driving. These door edge weatherstrips mount, with pre-installed pins, to seal the Left and Right doors when closed.
Door Flipper Stops
p/n: 70-2853-62
This Door Flipper Stop pair is designed from the original part for superior fitment and function. These rear flipper stops mount inside the flipper opening at the very rear of the door flipper.
Door Glass Run Channel
p/n: 20-1895-58
This Door Glass Run Channel is designed from the original part for superior fitment and function. Part is for the lock side at the rear of the front door. Rigid metal channel with fuzzy flocked lining.