Firewall Grommet
p/n: 30-0456-20
This Firewall Grommet is used for the heater core at the firewall. Designed from the original part for superior fit and seal.
Peel-N-Stick Trunk Weatherstrip
p/n: 20-1389-WT
This Peel-N-Stick Trunk Weatherstrip is designed for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body. Easy to install 3M Peel-N-Stick backing provides superior adhesion for reliable performance.
Brake and clutch shank seal
p/n: 70-0465-23
Grommets, brake and clutch pedal shank below floorboard.
Side Window Sash Channel
p/n: 70-0641-58
This Side Window Sash Channel is the u-shaped steel channel only, no filler. Sold in 4 foot strip, usually sufficient for two (2) windows.
2-5/8" Firewall Grommet
p/n: 70-1628-20
This Firewall Grommet is used for the wiring harness. Designed from the original part for superior fit and seal. Made from high-quality dense rubber to provide excellent durability.
Vent Window Division Post Weatherstrips
p/n: 20-0470-56
This Vent Window Division Post Weatherstrip is fully molded in high quality rubber and with a metal core. This part fits opposite the glass run channel and seals the vent window when the vent is closed. Part installs using the included rivets.
Sash Channel Weatherstrip
p/n: 60-0690-58
Weatherstrip, sash channel. Correct extrusion. Two (2) strips cut twenty five and one half (25-1/2) inches long.
Cowl Vent Gasket
p/n: 60-0124-54
Gasket, cowl vent. Original labyrinth style, not sponge.Length: 16.5 inches. Width: 4.0 inches.
Fabric Hood Lacing
p/n: 20-0354-42
This Fabric Hood Lacing installs where the hood rests on the cowl panel. Original woven style lacing complete with installation tacks. Sold as a forty-nine (49) inch strip.
Fuel Tank Filler Neck Grommet
p/n: 20-0345-39
This Fuel Tank Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Gearshift Floorplate
p/n: 20-0464-88
Seals, transmission cover to floor. Cork and rubber. Three (3) piece set.
Splash Apron / A-Arm Dust Shield Filler
p/n: 70-3060-45
This two (2) piece Splash Apron / A-Arm Dust Shield Filler pair is designed from the original part for superior fitment and seal. Filler pieces are die cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Steering Column Gasket
p/n: 70-2317-88
Insulator, steering column lower mounting frame gasket. Triangular shape with mounting holes and column tube clearance.
License Lens Gasket
p/n: 70-2121-17
Gasket, rear bumper license plate lens. Machine die-cut from 1/16" rubber.Length: 6.5625 inches. Width: 1.625 inches.
Firewall Grommet
p/n: 70-0967-20
This Firewall Grommet is used to run the windshield washer, vacuum lines, antenna lead, and other wires through the firewall. Designed from the original part for superior fit and seal.
Convertible Top Rest Bump Stop Block
p/n: 70-0397-67
This Convertible Top Rest Bump Stop Block pair is designed from the original part for an authentic fit, finish, and appearance. Attaches to the folding pillar arm of the convertible top assembly. This rubber only bumper block glues to the original metal core.
Hood Bumper Set
p/n: 20-3003-42
This ten (10) piece Hood Bumper set is designed from the original parts for superior fitment and function.
Hood to Radiator Weatherstrip
p/n: 40-0512-42
Weatherstrip, hood to grill or radiator shroud. Two (2) pieces, each sixteen (16) inches.Width: 1.3125 inches.
Rigid Run Channels
p/n: 70-0516-58
This Rigid Run Channel pair is zinc plated steel with black cloth inside lining to provide a smooth sliding surface for glass movement. Also works to protect the glass. Fastens in place by small screws or rivets on top and bottom.
Splash Apron
p/n: 20-3014-44
This six (6) piece Splash Apron set is designed from the original part for superior fitment and seal. Installs on the fender splash apron.
Vent division bar weatherstrip
p/n: 20-3040-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Vent Window Post Back Edge Weatherstrips
p/n: 20-3041-56
This Vent Window Post Back Edge Weatherstrips pair is designed from the original part for superior fitment and seal. These pieces mount on the vertical division bar with rivets and seal as the vent glass closes against them.
Hood to Cowl Weatherstrip
p/n: 60-0056-42
This Hood to Cowl Weatherstrip is extruded from a high quality dense rubber for a durable and proper seal. This seal mounts at the rear of the engine bay to seal between the hood and vehicle body cowl.
Accelerator Pedal
p/n: 60-0240-40
This reproduction Accelerator Pedal replaces worn or broken originals. Manufactured in quality black rubber. Steel core with hinge. Length: 8-15/16 inches.
Rear Window Gasket
p/n: 20-0419-81
This Rear Window Gasket is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the back glass and has vulcanized, or bonded, ends which means no cutting or splicing is required for installation.
Back-Up Light To Body Gasket
p/n: 70-3896-17
This Back-Up Light To Body Gasket pair are top quality molded rubber seals manufactured to authentic original dimensions.
Fuel Neck Grommet
p/n: 10-0123-41
Grommet, fuel filler neck. Fully molded soft flexible rubber. Two and seven sixteenths inch (2-7/16") outside diameter by one and seven sixteenths inch (1-7/16") inside hole diameter by five sixteenths (5/16") height.
Door Weatherstrip
p/n: 60-0664-73
Weatherstrip, auxiliary on body lock pillar. Correct extrusion cut thirty (30) inches long.
Rear Stone Deflector Seal
p/n: 20-2957-29
This Rear Stone Deflector Seal installs between the body and rear bumper. Includes six (6) clips for installation. Designed from original part so it fits correctly.
Drag Link End Repair Set
p/n: 20-0506-32
This Drag Link End Repair set is designed from the original parts for superior fit and function. This repair set will help your worn and aged steering connections to be once again as tight as the factory made them and help to make steering your classic truck easy again.
Convertible Roof Rail Weatherstrip T-Bolt Set
p/n: 70-4606-67
These Convertible Top Roof Rail Weatherstrip T-Bolt reproductions are designed from the original part for superior fitment and function. This twenty two (22) t-bolts and twenty two (22) nut set fastens to the convertible top bow weatherstrips.
Gravel Shield Bumper Set
p/n: 60-0146-30
This Gravel Shield Bumper Set is used as a rear bumper deflector. Also used between the radiator grille and the lower panel. Two (2) required per car. Designed from the original part for superior fitment and seal.
5" Wide Bow Drill Cloth Tape
p/n: 70-1175-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Brake and Clutch Shank Seal
p/n: 50-0066-24
Grommet, brake and clutch pedal floor seal.Width: 1.8125 inches. Height: 2.375 inches.
Brown Gearshift Boot - Steering Column
p/n: 30-0069-89
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Brown rubber. Two and one quarter (2-1/4) inches long.
Clutch Rod Boot
p/n: 20-2949-23
This Clutch Rod to Firewall Boot is designed from the original part for superior fitment and seal. This boot makes a weathertight connection for the clutch rod lever as it passes through the firewall.
Front Engine Mount
p/n: 20-2401-11
This Front Engine Mount is designed from original part for correct fitment and function. Rubber coated over a metal core for durability and proper engine vibration isolation. Two (2) required per car.
Front Fender Seal
p/n: 20-3010-44
This Front Fender Seal installs between the splash apron to fender and the rear of the splash apron to body. Sold as a one hundred forty (140) inch strip.
Air ventilator seal
p/n: 20-2965-31
Seals, air vent damper. Must drill out spot welds to replace the cracked rubber. Includes screws to put back together.
Brake and clutch shank seal
p/n: 70-0466-23
Grommet, brake and clutch pedal shank above floorboard. Special offset pattern as original.
Taillight Lens Gasket
p/n: 30-0353-15
Gasket, taillight lens to body mount. High quality replacement of normally deteriorated part. Nine and one half (9-1/2) inches long.Length: 9.50 inches.
Front Upper Engine Mount
p/n: 20-0503-11
This Front Upper Engine Mount is made of a quality dense rubber for maximum durability. Designed from original specifications for a correct fit and appearance.
Trunk Weatherstrip
p/n: 20-1389-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The seal mounts around the full perimeter of the trunk lid.
Clutch and Brake Pedal Pads
p/n: 60-0242-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Door Weatherstrip
p/n: 60-0313-73
Weatherstrip, door bottom. Retained by metal strip, black only. Each strip approximately thirty two and one half (32-1/2) inches long.
Hood to Cowl Weatherstrip
p/n: 60-0138-42
This Hood To Cowl Weatherstrip pair installs at the rear of the engine bay to seal between the hood and vehicle body cowl. Sold as a pair for left and right side.
Beltline Weatherstrip
p/n: 60-0287-58
Weatherstrip, door window at beltline, outer, (scraper type). Each strip approximately twenty six (26) inches to twenty seven (27) inches long.
Fuel Neck Grommet
p/n: 60-0271-41
Grommet, fuel filler neck. Oblong shaped molded rubber with retaining flange. Three and three fourths inch (3-3/4") outside length by three and five eighths inch (3-5/8") outside width.
Hood To Cowl Weatherstrip
p/n: 70-1698-43
This Hood To Cowl Weatherstrip mounts at the rear of the engine bay to seal between the hood and vehicle body cowl. A reproduction designed from original part so it fits correctly.
Rear Spring Pad
p/n: 70-2080-32
Pad, rear spring insulator. Order four (4) per car.Length: 4.75 inches. Width: 2.875 inches.
Fuel Neck Grommet
p/n: 60-0149-41
Grommet, fuel filler neck (1955-1st type). Oblong fully molded rubber with retaining flange. Three and seven eighths inch (3-7/8") outside width by five and one eight inch (5-1/8") outside length by one and one eighth inch (1-1/8") height.
Exhaust System Hanger
p/n: 60-0307-13
This Exhaust System Hanger is used for the muffler-to-tailpipe support (insulator) with reinforced webbing. Fully molded from top-quality EPDM dense rubber to ensure durability. One (1) required per car.
Clutch and Brake Pedal Pads - Black
p/n: 50-0054-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the pedal for a precise, factory fit. A perfect reproduction to replace worn original pedal pads. Manufactured in quality black rubber.
Starter Button
p/n: 60-0322-21
Starter button, push on replacement to rod. Two (2) inch outside diameter.
Door Bumper
p/n: 60-0334-71
Bumper, back door check link above door. Dovetail base fits check arm.Length: 1.0 inches. Width: 1.0 inches. Height: .625 inches.
Firewall Grommet
p/n: 60-0565-20
This Firewall Grommet is used to run the top hydraulic lines, wiring harness, and speedometer cable through the firewall. Designed from the original part for superior fit and seal.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Cowl to Fender Seal
p/n: 20-0443-45
Seal, front fender to cowl. Soft pliable sponge rubber designed to accurately fill the gaps between the back side of the fender and cowl. May be supplied as single strip that customer will have to cut in order to facilitate installation.
Front coil spring pad
p/n: 50-0358-35
Insulators, front coil spring. Fabric reinforced rubber as original.
Steering Column Connecting Rod Seal
p/n: 60-0400-36
Steering column steering connecting rod seal. Power steering models require one (1) per car. Non-power steering models require two (2) per car.
Brake and Clutch Pedal Pad
p/n: 60-0218-22
Pad, brake and clutch pedal. Length: 3.75 inches. Width: 2.375 inches.
Black Gearshift Boot - Steering Column
p/n: 30-0069-36
This steering column Gearshift Boot is designed from the original part for superior fitment, finish and function. Black rubber. Two and one quarter (2-1/4) inches long.
Brake and Clutch Pedal Bumper
p/n: 60-0579-24
Bumper, brake or clutch pedal to floorboard. Longer type with one and three eighths (1-3/8) inch clearance for pedal shaft.Length: 2.75 inches.
Brake and Clutch Pedal Bumpers
p/n: 60-0104-24
Bumpers, brake and clutch pedal shank, rides under floorboard. One and one eighth (1-1/8) inch clearance for pedal shaft. Compare with part 60-0579-24.
Front Bow Weatherstrip
p/n: 70-0785-64
Weatherstrip, front bow of convertible. Sponge rubber extrusion of correct dimensions.Length: 60.0 inches. Width: .8125 inches.
Gearshift Boot - Brown
p/n: 20-2166-26
This Gearshift Boot is designed from the original part for superior fitment and seal. This boot fits over the gearshift tower to make a weathertight connection for the transmission gearshift rod as it passes up through the vehicle floorboard.
Door Weatherstrips - Lower
p/n: 60-0078-73
This Lower Door Weatherstrip pair is designed from the original parts for superior fitment and seal. Heavy type with original ribbing and retainer lip.
Threaded Ends Insulator for Propeller Shaft and Exhaust Muffler
p/n: 70-0631-27
A steel core, double end threaded quality rubber Insulator that functions as an exhaust system muffler pipe bracket insulator. Also functions as a propeller shaft bearing to frame crossmember insulator.
Power brake carpet grommet
p/n: 70-3147-24
Grommet, carpet. Floor front carpet grommet use for power brake hole.
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
Steering Column Seal
p/n: 60-0518-36
Seal, steering column and shift column toe pan. Five eighths (5/8) inch thick sponge rubber.Width: 4.875 inches. Height: .625 inches.
Rear Spring Pad
p/n: 70-0191-32
Pad, rear spring insulator for two (2) inch wide springs. (see our number 70-0245-32 for two and one fourth (2-1/4) inch springs). Cloth reinforced. Four (4) per vehicle.
Fender Welting
p/n: 20-1591-44
This black Fender Welting is designed from the original part for superior fitment and seal. This welting material fits between the fenders and the vehicle body. Eight (8) foot length.
Brake and Clutch Pedal Pads
p/n: 70-3003-22
This reproduction Clutch and Brake Pedal Pad pair slips over the full perimeter of the brake pedal for a precise, factory fit. A square style direct fit reproduction to replace worn original pedal pads. Manufactured in black rubber.
Phototube Mounting Pad
p/n: 70-0721-17
Pad, phototube mounting on instrument panel. Automatic headlight beam control.Length: 2.3125 inches. Width: 1.6785 inches.
Side Window Vertical Leading Edge
p/n: 20-3126-80
Side window vertical leading edge weatherstrip. Cut to length. NOT cloth covered. This part attaches to the vertical edge of the rear side windows when the rear side windows are fully raised. Designed from the original part for superior fitment and seal.
Lower Door Weatherstrip Retainers
p/n: 20-0393-73
This Lower Door Weatherstrip Retainer pair is designed from the original part for superior fitment, finish and function. A pair of retainers for the lower door weatherstrips that mount on the left and right rocker sills. Does not include door weatherstrips.
Lock Pillar Water Deflector
p/n: 70-3635-62
Door panel water deflector, at lock. Fully molded for both left and right hand sides.