Taillight Mounting Pad
p/n: 30-0198-15
Mounting pad, taillight. With proper edging and shape, molded left and right. Sold only in complete pairs.Length: 9.75 inches.
Hood Corner Pad
p/n: 30-0225-42
Pads, front and rear hood corners, brass core, right angle.Length: 2.625 inches. Width: 2.625 inches.
Axle Rebound Pad
p/n: 70-1289-32
Bushing, rear support arm. Rear upper. Four (4) per car. For lower see #70-1290-32.
Axle Rebound Pad
p/n: 70-1290-32
Bushing, rear support arm. Rear lower. Four (4) per car. For upper see #70-1289-32.
Beltline Weatherstrip
p/n: 30-0301-57
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with stainless bead. Available in 3ft pair.
Bumper Grommet
p/n: 30-0039-28
Grommets, front or rear bumper. On models without trunk racks. Two (2) pair used per car if needing both front and rear bumper grommets.
Red Brake and Clutch Pedal Pad
p/n: 30-0114-89
Pads, brake and clutch pedal, slip over type. Black and red rubber. For black only see our #30-0114-22.
Hood to Cowl Weatherstrip
p/n: 30-0049-42
Scuff pad, hood to cowl. Superior duplication of part with better rubber than original.Length: 8.25 inches.
Rigid Run Channels
p/n: 30-0023-57
This Rigid Run Channel pair for the division bar is un-beaded, steel core, plush lined, and cloth covered. Available as 28" pair.
Front Suspension Bumper
p/n: 70-1294-32
Bumper, front load rebound, upper.Width: 1.625 inches. Height: 2.75 inches.
Cowl Vent Gasket
p/n: 30-0250-54
Gasket, cowl vent. Molded labyrinth style as original.Length: 13.50 inches.
Axle Rebound Pad
p/n: 30-0102-32
Pads, axle rebound, block type with flange. One and one half (1-1/2) inch by one and three fourths (1-3/4) inch by two and one half (2-1/2) inch overall.
Windshield Gasket
p/n: 19-0006-52
This Windshield Gasket comes in a four (4) foot strip and is for horizontally split windshields. The slot fits on the lower half and the projecting edge meets the upper half when the windshield is closed.
Prop shaft retainer bushing
p/n: 70-2268-27
Retainer, intermediate bearing. All models with two piece driveshafts.
Side Mount Grommet
p/n: 30-0205-37
Grommet, side mount support arm to running board splasher, right and left. Height: 4.25 inches.
Taillight Mounting Pad
p/n: 30-0230-15
Gaskets, taillight mounting. Proper type lip as original. One and eleven sixteenths (1-11/16) inch by four and one half (4-1/4) inch.Length: 4.25 inches.
Brake and Clutch Pedal Pads
p/n: 30-0188-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (semi-automatic clutch models) see our #30-0188-89.Length: 3.875 inches.
Front Bow Weatherstrip
p/n: 40-0418-65
This Front Bow Weatherstrip is designed from the original part for superior fitment and seal. Top quality extrusion cut five (5') feet long.
Headlight Mounting Pad
p/n: 30-0145-14
Pads, headlight bracket to fender mounting. Proper edge form.Length: 4.375 inches.
Detachable Center Post Pad
p/n: 30-0408-67
Pad, detachable center post, right and left hand.Width: 2.125 inches. Height: 2.6875 inches.
3" Firewall Grommet
p/n: 30-0110-42
This Firewall Grommet pair is used for the hood lock link through the firewall. Designed from the original part for superior fit and seal.
Taillight Mounting Pad
p/n: 30-0201-15
Pads, taillight bracket mounting, with proper beading and shape. For two and one eighths (2-1/8) inch by five and one half (5-1/2) inch base. Length: 5.
Taillight Mounting Pad
p/n: 30-0303-15
Gaskets, taillight assembly mounting. Molded left and right as original. Length: 10.25 inches.
Axle Rebound Pad
p/n: 30-0534-32
Bumper, rear axle rebound.Length: 3.0 inches. Width: 2.375 inches. Height: 1.6875 inches.
Headlight Mounting Pad
p/n: 30-0354-14
Gasket, headlight front assembly to fender. Between headlight bucket and the fender receiver hole. One (1) pair per car, sold only in pairs.
Fender Skirt Edge Weatherstrip
p/n: 20-0111-44
This Fender Skirt Edge Weatherstrip pair is designed from the original part for superior fitment, finish and sealing function. Two five (5) foot strips that fit between the rear wheel fender skirt and rear quarter panel.
Brake and Clutch Pedal Pads
p/n: 30-0114-22
Pads, brake and clutch pedal, slip over type. Black rubber only. For black and red (electromatic clutch models) see our #30-0114-89.
Headlight Lens Gasket
p/n: 30-0176-14
Gaskets, headlight lens and reflector mounting. A three sixteenths (3/16) inch cross section rubber ring of proper diameter.
Radiator Mounting Pad
p/n: 30-0309-31
Grommet, several usages. Radiator core cradle tie rod to frame or rear stabilizer pad to link to where the leaf springs are bolted. Fully molded rubber. 2nd type with chamfered edge. Comes as a (4) piece set.
Suspension bushing
p/n: 30-0339-36
Bushing, insulator, front suspension lower support arm, inner. Four (4) piece set.
Suspension bushing
p/n: 30-0335-36
Bushing, insulator, torque arm to frame at rear. Four (4) piece set.
Vent division bar weatherstrip
p/n: 30-0532-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Carpet Heel Plate
p/n: 70-3019-88
Heel pad for carpet. Seven and three eighths (7-3/8) inch wide by sixteen (16) inches long.
Front Stabilizer Bar Bushing
p/n: 70-1293-33
A Front Stabilizer Bar to Frame Bushing pair for both sides of the vehicle. Fits front stabilizer or sway bar. Manufactured with quality materials to original specifications. One (1) pair per vehicle.
Fuel Neck Grommet
p/n: 30-0099-41
Grommet, fuel filler neck. Three and one half (3-7/16) inch inside diameter for four (4) inch hole in apron.
Convertible Top Front Bow Weatherstrip
p/n: 30-0503-65
This Convertible Top Front Bow Weatherstrip is designed from the original part for superior fitment and seal. This seal installs directly to the convertible top to seal between the soft top and the top of the windshield.
Front Stabilizer Bushing
p/n: 30-0363-33
Bearings or bushings, front stabilizer rod. One (1) pair used per vehicle. Fully molded rubber.
Fuel Filler Neck Grommet
p/n: 30-0158-41
This Fuel Filler Neck To Body Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Fuel Neck Grommet
p/n: 30-0101-41
Grommet, fuel filler neck. For inside of body, on floor of wheel carrier.
Fuel Neck Grommet
p/n: 30-0232-41
Grommet, fuel filler neck. 2-1/2" inside diameter. Fits 3-3/8" hole in sheet metal. Overall width 4-1/8".
Vent division bar weatherstrip
p/n: 30-0540-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Rear Window Gasket
p/n: 70-0084-77
This Rear Window Gasket comes in a seven foot, six inch (7' 6") strip and mounts around the full perimeter of the back glass. The ends may require trimming and bonding for installation.
Vent division bar weatherstrip
p/n: 70-1511-56
Front vent window division post seal. Fully molded with metal core and attaching tabs.
Rear Shield to Bumper Seal
p/n: 30-0476-44
This Rear Shield to Bumper Seal is made of high quality EPDM dense rubber. The seal is designed from an original part so it fits correctly. Overall length is seven (7) feet.
Door Bumper
p/n: 34-0305-71
Bumper assembly, front door hinge, upper, stop. Two (2) per car, steel core as original.Height: .6875 inches.
Vent Window Division Bar Weatherstrip
p/n: 30-0541-74
Division post seal pair for rear door vent window. Made from top quality rubber to ensure durability and proper seal. Designed from original part so it fits correctly.
Hood Corner Pad
p/n: 30-0037-42
Pads, hood front corner. Metal core, retained by single rivet.Length: 1.75 inches. Width: 1.375 inches.
Taillight Mounting Pad
p/n: 30-0318-15
Gaskets, taillight mounting, with proper beading and shape as original. For all models with center license mounting. Length: 7.125 inches.
Suspension bushing
p/n: 30-0341-36
Bushing, insulator, upper support arm, outer above steering knuckle support. Four (4) piece set.
Taillight Mounting Pad
p/n: 30-0148-15
Mounting pad, taillight bracket to fender, with correct beading and shape. Length: 4.5625 inches. Width: 1.875 inches.
Side Mount Grommet
p/n: 30-0079-37
Grommet, sidemount brace, lower, to fender. Hollow construction for good fit.
Front Stabilizer Bushing
p/n: 30-0123-33
Bushings, front stabilizer mounting bracket. Fully molded rubber.
Fuel Neck Grommet
p/n: 30-0241-41
Grommet, gas tank inlet to wheel housing. Also used as grommet, gas tank inlet tube to wheel compartment bottom.
Hood Bumper
p/n: 30-0151-42
Bumpers, hood catch. Right and left.Length: 2.50 inches. Width: 1.4375 inches.
Beltline Weatherstrip
p/n: 30-0300-58
Window felt inner and/or outer. Flexible, pile lined, rubber covered, with stainless bead. Available in 3ft pair.
Front Header Bow Weatherstrip
p/n: 70-1298-64
Weatherstrip, front of front header bow seal. Five (5) foot long extrusion. Made from top quality rubber to ensure durability and proper seal.
Cowl Vent Gasket
p/n: 30-0050-54
Gasket, cowl vent. Perfect reproduction, high quality, original configuration, not a sponge substitute.Length: 14.0 inches. Width: 5.75 inches.
Radiator Mounting Pad
p/n: 30-0208-31
Pad, radiator lower splasher to grille. Fastens into place with rivets. One four (4) piece set required per car.Length: .875 inches. Width: .875 inches.
Firewall Grommet
p/n: 30-0070-21
This Firewall Grommet is used to run instrument board cables through the firewall. The oval type with masked hole for six (6) wires or cables is the necessary replacement for correct restoration.
Brake Cable Anti-Rub Cover
p/n: 60-0443-24
Sleeve, rear brake cable anti-rub. Six (6) piece set. One half (1/2) inch inside diameter, seven eighth (7/8) inch outside diameter.
Coil Wire Sleeve
p/n: 70-2052-21
Boot, spark plug wire, at spark plug. All original textures and details.Length: 2.0 inches.
Windshield Side Weatherstrips
p/n: 30-0074-52
This Windshield Side Weatherstrip pair is designed from the original part for superior fitment and seal. Windshield side, inner frame to windshield post, upper, fits dovetail slot in swinging glass frame.
Parking Light Mounting Pad
p/n: 30-0416-17
Gasket, fender light. Faithful copy with correct shape and detail as originalLength: 2.75 inches.
Parking Light Mounting Pad
p/n: 30-0282-17
Gaskets, parking light (fender light).Length: 2.75 inches. Width: 1.75 inches.
Radiator Mounting Pad
p/n: 30-0395-31
Spacer or Pad, radiator anchorage stud, upper stud. One (1) pair required per car.Length: 2.5625 inches.
2-3/8" Firewall Grommet
p/n: 30-0056-21
This Firewall Grommet is made to run the ignition cable and thermometer tube through the firewall. Designed from the original part for superior fit and seal.
Back-Up Light To Body Gasket
p/n: 70-3895-17
This Back-Up Light To Body Gasket pair are top quality molded rubber seals manufactured to authentic original dimensions.
Cowl Vent Gasket
p/n: 30-0096-54
Gasket, top cowl vent. Closed cell sponge rubber. One half (1/2) inch by three fourths (3/4) inch. Rectangular cross section.
Cowl Vent Gasket
p/n: 30-0519-54
Gasket, cowl vent. Die cut sponge with smooth curves. Excellent reproduction designed to fit in gutter and not bind when closing.Length: 15.75 inches.
Front Stabilizer Bushing
p/n: 30-0298-33
Bushings, front stabilizer rod end. One (1) pair required per car. Fully molded rubber.
Hood Inner Center Rest Pad
p/n: 30-0222-42
This Hood Inner Center Rest Pad pair is designed from the original part for an authentic fit, finish, and appearance. Rubber only pads that fit original bracket.
Cowl Vent Gasket
p/n: 30-0179-54
Gasket, cowl vent, original labyrinth type, not sponge.Length: 14.75 inches. Width: 5.50 inches.
Engine Mount
p/n: 30-0292-11
This Engine Mount pair is used as the engine crank case link ball insulator. Correctly designed with careful attention to detail as original. Sold only in pairs.
Ignition Cable Grommet
p/n: 70-1598-21
Grommet, ignition cable.Length: 2.125 inches. Width: 1.50 inches.
Side Mount Grommet
p/n: 30-0100-37
Grommets, spare wheel sidemount brace, lower.Length: 2.625 inches. Width: 2.50 inches.
Radiator Mounting Pad
p/n: 30-0209-31
Shim, radiator core mounting stud spacer. Fully molded rubber. Use as required. Comes as a pair of two (2). Two and seven eighths inch (2 7/8") square by five eighths inch (5/8") inside hole diameter by three eighths inch (3/8") height.