Front Stabilizer Bushing
p/n: 30-0363-33
Bearings or bushings, front stabilizer rod. One (1) pair used per vehicle. Fully molded rubber.
Front Stabilizer Bushing
p/n: 30-0123-33
Bushings, front stabilizer mounting bracket. Fully molded rubber.
Front suspension bumper
p/n: 30-0229-32
Bumper assembly, front suspension rebound (upper arm). Straight style with stud.
Front Suspension Bumper
p/n: 30-0489-32
Bumper, front suspension (inside of coil spring). Made with three eighths (3/8) inch stud as original.
Front Suspension Bumper
p/n: 30-0228-32
Bumper assembly, front suspension inside coil spring, with five sixteenths (5/16) inch threaded studs as found originally.
Front Suspension Bumper
p/n: 70-1294-32
Bumper, front load rebound, upper.Width: 1.625 inches. Height: 2.75 inches.
Front Suspension Bumper
p/n: 70-1295-32
Bumper assembly, front load compression, lower.Width: 2.125 inches. Height: 2.75 inches.
Front Suspension Bumper
p/n: 30-0490-32
Bumper, front suspension (inside of coil spring). Made with three five sixteenths (5/16) inch studs as original.
Front suspension bushing
p/n: 30-0239-32
Bushings, front suspension torque arm. Necessary for proper front end geometry.
Fuel Filler Neck Grommet
p/n: 30-0158-41
This Fuel Filler Neck To Body Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Fuel Line Grommet
p/n: 30-0320-41
Grommet, fuel line through engine pan. Two and one fourth (2-1/4) inch diameter.
Fuel Line Grommet
p/n: 30-0045-41
Grommet, fuel gauge and gas line through rear frame cross member. For five eighths (5/8) inch by two and three eighths (2-3/8) inch slot.Length: 2.
Fuel Neck Grommet
p/n: 30-0101-41
Grommet, fuel filler neck. For inside of body, on floor of wheel carrier.
Fuel Neck Grommet
p/n: 30-0099-41
Grommet, fuel filler neck. Three and one half (3-7/16) inch inside diameter for four (4) inch hole in apron.
Fuel Neck Grommet
p/n: 30-0241-41
Grommet, gas tank inlet to wheel housing. Also used as grommet, gas tank inlet tube to wheel compartment bottom.
Fuel Neck Grommet
p/n: 30-0232-41
Grommet, fuel filler neck. 2-1/2" inside diameter. Fits 3-3/8" hole in sheet metal. Overall width 4-1/8".
Fuel Neck Grommet
p/n: 30-0157-41
Seal, fuel filler neck through rumble seat floor pan. Highest quality workmanship, rubber with brass core as original.
Fuel Tank Support Pad
p/n: 30-0482-41
This Fuel Tank Support Pad is made of a high quality EPDM dense rubber. This cushion is used to help reduce noise. Available by the foot.
Gearshift Boot
p/n: 30-0178-24
Boot, gearshift cover. For cane shifts only. Length: 4.0 inches. Width: 3.0 inches. Height: 5.125 inches.
Gearshift Boot
p/n: 30-0129-24
Boot for column gearshift, short type. Black rubber. For brown see our #30-0129-89. All series with column shift.Height: 1.4375 inches.
Gearshift Boot
p/n: 30-0412-24
Grommet, shifter shaft to shroud. One (1) per car.Length: 4.125 inches. Width: 2.3125 inches.
Gearshift Seal
p/n: 30-0165-24
Seal, gearshift to floorboard.Length: 5.625 inches. Width: 4.875 inches.
Gravel Shield
p/n: 30-0007-44
Gravel deflector, underside of running board at rear. Length: 7.125 inches.
Gravel shield bumper
p/n: 70-2825-44
Anti-rattler, front stone shield. Insulates the front stone shield from the front bumper. Six (6) piece set.
Gravel Shield Bumper
p/n: 30-0384-44
Cushion, rear gravel to bumper. Six (6) feet long. One (1) strip required per car.Length: 72.00 inches. Width: .25 inches. Height: .6875 inches.
Hardtop Weatherstrip
p/n: 70-2012-68
Weatherstrip, hardtop roof rail, auxiliary. Installed in side window flipper seal. This is a factory service department fix designed to reduce wind noise on 56th series hardtops that also can be used on 55th series models.
Harmonic Balancer - Revulcanization Service
p/n: 30-0520-12
This front Harmonic Balancer - Revulcanization Service is designed to restore your engine's vibration damper to a like new original condition. Service only requires your metal core. Please call or email for more service details and ordering.
Headlight Lens Gasket
p/n: 30-0176-14
Gaskets, headlight lens and reflector mounting. A three sixteenths (3/16) inch cross section rubber ring of proper diameter.
Headlight Mounting Pad
p/n: 30-0142-14
Gaskets, headlight body mounting to fender. Cut to exact size as original.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Headlight Mounting Pad
p/n: 30-0291-14
Pads, headlight support bar to fender. Molded right and left.Length: 3.75 inches. Width: 3.75 inches.
Headlight Mounting Pad
p/n: 30-0265-14
Mounting pad, headlight bracket to fender. Molded right and left with proper beading and shape as original.Length: 9.375 inches.
Headlight Mounting Pad
p/n: 30-0134-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. Made with a metal core. This pad acts as the headlight adjusting collar.
Headlight Mounting Pad
p/n: 30-0354-14
Gasket, headlight front assembly to fender. Between headlight bucket and the fender receiver hole. One (1) pair per car, sold only in pairs.
Headlight Mounting Pad
p/n: 30-0145-14
Pads, headlight bracket to fender mounting. Proper edge form.Length: 4.375 inches.
Headlight Mounting Pad
p/n: 30-0133-14
Pads, headlight bracket mounting to fender. Molded left and right. Proper construction with beading as original. Sold in complete pairs only.Length: 9.
Headlight Mounting Pad Set
p/n: 30-0236-14
Pad set, headlight mounting. Six (6) piece replacement set. Sold in complete sets only.
Headlight Mounting Pad Set
p/n: 30-0161-14
Pad and Grommet Set, headlight support bar to radiator shell. Four (4) piece set, sold in complete sets only.
Headlight stanchion pad
p/n: 30-0240-14
Cushion (rubber washer), front light to radiator shell. One (1) pair required per car.
Headliner Retainer Grommet
p/n: 70-1713-88
Grommet, headliner bow end. Twelve (12) required per car.Length: 1.4375 inches.