Accelerator Rod Seal
p/n: 40-0205-88
This Accelerator Rod Seal is used as an accelerator rod through the toeboard. Molded from a high-quality EPDM dense rubber.
Side Mount Grommet
p/n: 40-0140-37
Grommet, sidemount carrier brace to fender. One and five sixteenths (1-15/16) inch outside diameter by one half (1/2) inch inside diameter.
Door Plug Beltline Extender
p/n: 70-3214-62
This Door Plug Beltline Extender pair is designed from the original part for superior fitment and seal. This piece works on beltline as an extender. Width: 2.0 inches.
Taillight Mounting Pad
p/n: 40-0299-15
Mounting pad, taillight bracket to fender. This is a plain, flat un-beaded pad as original, and reversible. Four and three fourths (4-3/4) inch long.
Brake and Clutch Shank Seal
p/n: 40-0016-24
Seal, brake and clutch pedal shank to floorboard (draft excluder).Length: 2.4375 inches. Width: 1.875 inches.
Firewall Grommet
p/n: 40-0222-21
This Firewall Grommet is used to run the throttle cable and wiper vacuum line through the firewall as well as a drain hole for the cowl vent. The holes in the three (3) hole design measure: 9/16", 3/8", and 1/4".
Fuel Filler Neck Grommet
p/n: 70-3622-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Firewall Grommet
p/n: 40-0221-21
This Firewall Grommet is used to run the speedometer cable, oil tube, and the temperature tube through the firewall. The three (3) holes measure 5/16", 1/4", 3/16".
Engine Top Cover Weatherstrip
p/n: 70-4750-88
This Engine Top Cover Gasket is an original design reproduction made from top quality sponge rubber. This gasket attaches between the removable engine cover ("doghouse") and the vehicle firewall / floorboard.
Trunk Weatherstrip
p/n: 70-3052-84
This Trunk Weatherstrip is designed from the original part for superior fitment and seal. The weatherstrip mounts around the full perimeter of the trunk directly to the body.
Window Gasket Locking Strip - Chrome
p/n: 70-1919-52
This chrome appearing Window Gasket Locking Strip is designed from the original part for superior fitment and seal. Locking strip serves as the front or rear window gasket retainer. Sixteen (16') foot length single piece, one application, for complete coverage.
Fuel Neck Grommet
p/n: 70-2284-41
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body. Fully molded out of gasoline resistant BUNA high quality rubber.
Firewall Grommet
p/n: 40-0223-21
This Firewall Grommet can be used for a variety of applications since the grommet is plain (no holes). Designed from the original part for superior fit and seal.
Door handle gasket
p/n: 40-0191-70
Pad, outside door handle escutcheon. Compare with our #40-0207-70.
1-7/16" Firewall Grommet
p/n: 40-0204-21
This Firewall Grommet is used to run the wiring harness through the firewall. Designed from the original part for superior fit and seal.
Windshield Division Bar Gasket
p/n: 70-0098-52
This Windshield Division Bar Gasket is designed from the original part for superior fitment and seal. Part combines inner and outer gasket in one piece as original. For seventeen (17") inch to (20") inch lengths.
Brake and Clutch Pedal Pad
p/n: 40-0287-22
Pads, brake and clutch pedal. Length: 3.625 inches. Width: 2.0 inches.
Taillight Mounting Pad
p/n: 40-0092-15
Pad, taillight mounting, plain type without bead. Compare with our #40-0299-15. Length: 4.3125 inches. Width: 2.25 inches.
Window Locking Strip - Black
p/n: 70-2195-52
This extruded Locking Strip is used to retain windshield gaskets in pickups and vans. Designed from the original part for superior fitment, finish and function. Available in 16ft lengths.
Taillight Mounting Pad
p/n: 40-0061-15
Pad, taillight mounting. Chrysler 1932-33 Pad, taillight mounting. Chrysler and other WPC cars. Chrysler 1932-33 Pad, rumble seat step mounting.
Hood to Fender Bumper
p/n: 70-2046-42
This Hood to Fender Bumper pair is a quality reproduction of the original factory part. These rubber bumpers attach to the front fender to support / cushion the hood closure.
Cowl Drain Gutter Hose Grommet
p/n: 40-0202-54
Grommet, cowl drain. One and seven sixteenths (1-7/16) inch outside diameter for seven sixteenths (7/16) inch drain hose through firewall.
Splash Apron / A-Arm Dust Shield Filler Set
p/n: 70-4670-45
This four (4) piece Splash Apron / A-Arm Dust Shield Filler set is designed from the original part for superior fitment and seal. Filler pieces are die-cut from quality masticated rubber to authentic original dimensions. Left and Right pieces fit over suspension a-arms and inside front inner fenders.
Door handle gasket
p/n: 70-2628-69
Gasket set, door handle. Machine die cut to original profile. Each set is enough for two doors.
Vent Window Division Bar Weatherstrip
p/n: 70-1432-56
This Front Vent Window Division Bar Weatherstrip is designed from the original part for superior fitment and seal. A single 32" inch (approximate) length of original cross-section extruded rubber.
Window Locking Strip - Black
p/n: 70-1918-52
This Window Locking Strip is designed from the original part for superior fitment and function. Front or rear window retainer made from top quality black EPDM rubber. Available in 15ft lengths.
Door Bumper
p/n: 40-0131-70
Bumper, door side. Approximate size one half (1/2) inch by three fourth (3/4) inch by two (2) inch. Length: 2.0 inches. Width: .50 inches.
Steering Column Cushion
p/n: 40-0259-36
Pad, steering post bracket. One (1) per car. Cushions steering post clamp to instrument panel.Length: 3.50 inches.
Inner Fender Splash / Dust Shield Set
p/n: 70-4669-45
This four (4) piece Inner Fender Splash / Dust Shield Set is designed from the original part for superior fitment and seal. Inner Fender pieces are die-cut from quality masticated rubber to authentic original dimensions. These pieces fit to the inner front fenders.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Hood Support Rod Top Cap
p/n: 40-0346-42
Pad, hood rest rod. For five sixteenths (5/16) inch diameter hood support rod. Also see our #40-0103-42.Length: 1.0 inches.
Body Mounting Pad
p/n: 40-0232-48
Pad, body mounting, upper. Fully molded rubber with locating collar. As many as twelve (12) used per car. One and fifteen sixteenths inch (1 15/16") outside width by two inch (2") outside width. See drawing for more dimensions.
Body Mounting Pad
p/n: 40-0453-48
Insulator, body mounting. Fully molded rubber with locating collar. Use as required. Up to eight (8) are used per car.
Steering gear bushing
p/n: 40-0130-36
Bushing, insulator, for steering gear arm. Four (4) required per car.
Fuel Filler Neck Grommet
p/n: 70-2580-39
This Fuel Filler Neck Grommet is designed from the original part for superior fitment and seal. This grommet fits around the vehicles fuel filler neck between the filler neck and vehicle body.
Door Bumper
p/n: 40-0235-70
Bumper, door striker plate. Two (2) per door, front and rear.Length: 1.375 inches. Width: .50 inches.
Exhaust Support Grommet
p/n: 60-0031-13
This Exhaust Support Grommet is designed from the original part for superior fitment and usage. The OEM direct fit application is as a rear and middle muffler exhaust support hanger.
Quarter Window Vertical Leading Edge
p/n: 83-1012-80
This quarter and side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. A reproduction weatherstrip manufactured to OEM specifications to install for an authentic fit and finish.
Coil wire sleeve
p/n: 40-0336-21
Nipple, sparkplug wire at sparkplug, for right angle plug terminal. This is an exact copy of the style used at the time. Not a modernistic makeover.
2-1/2" Black Bow Drill Cloth Tape
p/n: 70-1172-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Hood Bumper
p/n: 82-0212-42
Bumper, hood to fender ledge. Excellent reproduction, made just like original.
2-1/2" Tan Bow Drill Cloth Tape
p/n: 70-1173-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.