Headlight Door To Lens Weatherstrips
p/n: 70-0493-14
This Headlight Door To Lens Weatherstrip pair is the double lip type for sealed beam headlights. The pair is molded without wire. Designed from the original part to fit correctly.
Headlight Mounting Pad
p/n: 70-0201-14
This Headlight Mounting Pad is designed from the original part for superior fitment and seal. This pad acts as the headlight adjusting collar. Sold as a pair.
Hinge Pillar Weatherstrip
p/n: 70-0378-63
Convertible Hinge Pillar Weatherstrip - Attaches to the body and seals between the A-pillar post and the front section of the door or vent window frame when the door is closed. Note: order #70-0379-68 hardtop roof rail seals separately.
Hood and Trunk Bumper Cap for Adjustment Screw
p/n: 70-0294-42
This Hood and Trunk Bumper Cap is designed from the original part for superior fitment, finish and function. Cap type for front hood or rear trunk lid adjustment screw.
Hood Corner Pad
p/n: 70-0914-42
Pad, hood corner. Molded left and right like original.Width: 1.375 inches.
Hood to Cowl Weatherstrip
p/n: 70-1211-42
Weatherstrip, hood to cowl. High quality rubber molded in one piece as original.
Hydraulic Pump Grommet
p/n: 70-0640-21
Grommet, two (2) hole, for hydraulic pump through sheet metal.Length: 1.9375 inches. Width: 1.125 inches.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Lower Suspension Arm Dust Seal
p/n: 70-0624-32
Dust seal, "O" ring. Lower suspension arm pin bushing. Four (4) required per car.Height: .25 inches.
Lower suspension arm dust seal
p/n: 70-0646-32
Seal, lower suspension arm, inner. Four (4) piece set.
Masticated Rubber Sheet
p/n: 70-0645-45
This Masticated Rubber Sheet is three-thirty seconds (3/32) inch thick. The rubber sheet contains random milled cotton cord reinforcement for front end splash aprons, etc.
Metal Sleeved Grommet
p/n: 70-0203-41
Flanged rubber grommet with metal sleeve bushing. Used as part of the accelerator relay lever. Also used from 1959-61 on all Cadillac models as a bushing for the windshield wiper relay lever adaptor.
Parking/Backup Light Lens Gasket
p/n: 70-1272-16
Gasket, parking light lens and backup light lens. Die cut from one eighth (1/8) inch rubber.
Peel-N-Stick Door Edge Weatherstrip
p/n: 70-0390-WT
This Peel-N-Stick Door Edge Weatherstrip is designed for a specific set of vehicles but with its generic shape, has many uses outside of its original purpose. Available by the foot. Available by the foot.
Peel-N-Stick Door Weatherstrip
p/n: 70-0331-WT
This Peel-N-Stick Door Weatherstrip is made from high-quality EPDM sponge rubber. Available by the foot.
Power Top Cylinder Spacer
p/n: 70-0822-67
This Power Top Cylinder Spacer is used as the folding top power cylinder support. Molded from 100% EPDM dense rubber for durability. Four (4) spacers used per car.
Pressure Ring
p/n: 70-0261-69
Pressure ring (washer), sponge rubber, interior door handle and window regulator escutcheon. One and three fourths (1-3/4) inches outside diameter by three eighths (3/8) inch thick.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Rear Axle Bumpers
p/n: 70-0210-32
This Rear Axle Bumper pair is a quality reproduction of the original factory part. These bottoming pads are dense rubber blocks that mount by bracket to the rear axle tube.
Rear Gravel Deflector to Bumper Face Bar
p/n: 70-0462-45
This Rear Gravel Deflector to Bumper Face Bar staples to the gravel deflector. The seal is die cut from dense rubber. Sold as a six (6) foot strip.