Front Bow Weatherstrip
p/n: 70-0785-64
Weatherstrip, front bow of convertible. Sponge rubber extrusion of correct dimensions.Length: 60.0 inches. Width: .8125 inches.
Trunk Bumper
p/n: 70-0296-87
T-nut, trunk bumper in gutter at sides, brass core tapped 10-32 thread. Two (2) required per car. For models having partial weatherstrip in gutter of body.
Heater control valve seal
p/n: 50-0356-20
Seal, heater control valve. High quality sponge rubber designed to cushion heater control valve and keep out noise and water. For all except right-hand drive.
Body Mounting Pad
p/n: 50-0477-48
Pad, body mounting. Fully molded rubber with metal core & locating collar.
Taillight Mounting Pad
p/n: 50-0410-15
Pad, taillight to fender. Width: 7.25 inches. Height: 4.0 inches.
Door Handle Gasket Set
p/n: 50-0322-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Taillight Lens Gasket
p/n: 50-0411-15
Gasket, taillight lens. Die cut three sixteenths (3/16) inch sponge rubber as original.Width: 6.25 inches. Height: 3.25 inches.
Hydraulic Pump Mounting Cushion
p/n: 70-0852-67
This Hydraulic Pump Mounting Cushion is designed from the original part for superior fitment and function. Used on models with hydraulic window lifts or a hydraulic convertible top. Two (2) to three (3) required per car.
Quarter Window Vertical Leading Edge
p/n: 70-0141-58
This quarter to side window Vertical Leading Edge Weatherstrip pair is designed from the original part for superior fitment and seal. Slides into metal retaining channel attached to rear side window and seals between the front door window and the rear quarter window.
Battery Clamp Cover
p/n: 70-0095-21
This Battery Clamp Cover helps to protect the nearby metal and finish. Fully molded from high-quality EPDM rubber to ensure durability. Good copy from an original part.
Hood Bumper
p/n: 50-0159-42
Bumper, hood ledge corner at shroud.Width: 1.25 inches. Height: .5 inches.
2-1/2" Black Bow Drill Cloth Tape
p/n: 70-1172-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Black in color and available in a five (5) foot roll.
Body Mounting Pad
p/n: 50-0478-48
Pad, body mounting. Fully molded rubber with locating collar. Two (2) are needed per car.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
Body Mounting Pad
p/n: 50-0096-48
Pad, body mounting. Fully molded rubber with steel core and locating collar.
2-1/2" Tan Bow Drill Cloth Tape
p/n: 70-1173-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
Parking, Signal or Backup Light Lens Gaskets
p/n: 50-0381-16
This front Parking and Turn Signal Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Light Lens and the Light Housing or Bezel. Also fits Backup Light Lens on cars with optional Backup Lights.
Hood Bumper
p/n: 50-0277-42
Bumper, hood side to fender ledge. Metal core molded in as original.Width: 1.875 inches. Height: .8125 inches.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Body Mounting Pad
p/n: 50-0361-48
Pad, body mounting. Required replacement for body-off restorations. Constructed of high quality rubber for long lasting durability. Two inch (2") square by fifteen sixteenths inch (15/16) inside hole diameter by one fourth inch (1/4") height.
1-5/8" Firewall Grommet
p/n: 50-0364-20
This Firewall Grommet is used to run the oil pressure and water temperature, or washer vacuum hose through the firewall. Designed from original part for excellent workmanship.
License lens gasket
p/n: 50-0357-17
Gasket set, rear license light assembly. One (1) rubber ring and one (1) cork rubber gasket comprise set.