Trunk Bumper
p/n: 50-0546-87
Bumper, trunk. On side near hinge end. Made with metal core.Width: 1.625 inches. Height: 1.0 inches.
Window Stop Stem Bumper
p/n: 33-0675-62
Cushion (stem bumper), window stop, lower. For front and rear door, rear side and quarter windows as required.
Body Mounting Pad
p/n: 50-0130-48
Pad, body mounting. Fully molded rectangular rubber with locating collar.
Body Mounting Pad
p/n: 50-0096-48
Pad, body mounting. Fully molded rubber with steel core and locating collar.
Rear coil spring pad
p/n: 50-0304-35
Insulator, rear coil spring clamp bolt (upper end). Two (2) per car. Fabric reinforced rubber as original.
1-3/16" Standard Grommet
p/n: 32-0328-54
This Standard Grommet is fully molded and designed from the original part for superior fitment and seal. This grommet is made from high-quality EPDM dense rubber to provide excellent durability.
Windshield Wiper Transmission Gaskets
p/n: 70-1196-53
This Windshield Wiper Transmission Gasket pair is designed from the original part for superior fitment and function. This gasket mounts between the windshield wiper transmission and the vehicle body work to reduce noise and vibration.
Axle Rebound Pad
p/n: 50-0303-35
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car.
Glovebox Door Link Grommet
p/n: 70-0968-88
This Glovebox Door Link Grommet is designed from the original part for superior fitment and function. Grommet works to cushion the glovebox door closure.
1-1/2" Firewall Grommet
p/n: 50-0299-20
This Firewall Grommet is used to run the oil pressure and water temperature lines through the firewall. Designed from original part for excellent workmanship.
2-1/2" Tan Bow Drill Cloth Tape
p/n: 70-1173-65
This Bow Drill Cloth Tape is used for covering convertible side window weatherstrip. Tan in color and available in a five (5) foot roll.
Antenna Mount Pad
p/n: 50-0168-21
Pad, antenna mounting over windshield, one and thirteen sixteenths (1-13/16) inch outside diameter, one and one fourth (1-1/4) inch inside diameter.
Folding seat bumper
p/n: 70-2579-88
Bumper, folding front seat frame rest cushion. Manufactured from dense rubber with a molded in metal retaining washer. Two (2) used per car.
Hood to Fender Bumper
p/n: 70-3445-42
Bumpers, hood to fender. Set of four (4). Proper cross section with original details approximately five eights (5/8") of an inch wide.
Wiper Transmission Gasket
p/n: 70-1197-53
Gasket, windshield wiper transmission. Replaces #4074294 & #4082366.
Parking, Signal or Backup Light Lens Gaskets
p/n: 50-0381-16
This front Parking and Turn Signal Light Lens Gasket pair is designed from the original part for superior fitment and seal. This reproduction gasket fits between the Light Lens and the Light Housing or Bezel. Also fits Backup Light Lens on cars with optional Backup Lights.
Parking/Backup Light Lens Gasket
p/n: 70-1272-16
Gasket, parking light lens and backup light lens. Die cut from one eighth (1/8) inch rubber.
Wiper Transmission Gasket
p/n: 70-1198-53
Gasket, windshield wiper transmission (1939-later type). Replaces #4097038.
Brake Pedal Pad - Automatic
p/n: 60-0710-22
This reproduction Brake Pedal Pad slips over the full perimeter of the brake pedal for a precise, factory fit. A direct fit to replace worn, heavy wear original brake pedal pads. For GM models with an automatic transmission.
Ferrule and Grommet Set
p/n: 70-0597-69
This Ferrule and Grommet Set for the outside door handle is cadmium plated ferrule with rubber sleeve. Two (2) piece set for one (1) door.
Front Bumper Gravel Shield
p/n: 70-0127-30
This anti-rattle Front Bumper Gravel Shield pad is designed from the original part for superior fitment and seal. Fully molded with top quality EPDM rubber over a corrosion resistant brass core to ensure durability, fit and appearance.
1-3/8" Firewall Grommet
p/n: 50-0531-20
This Firewall Grommet is used to run the oil pressure, water temperature, and vacuum line through the firewall. Designed from original part for excellent workmanship.
Beltline Guide Plate - Plastic
p/n: 50-0384-62
This Beltline Guide Plate is designed from the original part for superior fitment and function. High quality plastic plate attaches to various outer beltline window scraper weatherstrips.
Body Mounting Pad
p/n: 50-0329-48
Pad, body mounting. Under frame bracket for hold-down nut. Fully molded rubber. Check number needed for your particular body.
Door Check Link Rod End Stop
p/n: 70-0326-70
End stop and pad, door check link rod. Rubber with embedded steel plate, five sixteenths (5/16) inch diameter thread. Most models with rod type door checks.
Front Door Lock Pillar Filler
p/n: 70-0834-79
This Front Door Lock Pillar Filler pair is designed from the original part for superior fitment and sealing. This left and right weatherstrip filler seals the bottom at the front of the rear side window. Also known as a door jamb seal.
Body Mounting Pad
p/n: 50-0232-48
Shim, body sill, for #3, #5, and #7 body bolts. Six (6) per car. Width: 2.0 inches. Height: 2.0 inches.
Hood Bumper
p/n: 50-0277-42
Bumper, hood side to fender ledge. Metal core molded in as original.Width: 1.875 inches. Height: .8125 inches.
Wiper Transmission Gasket
p/n: 70-0499-53
Gasket, wiper transmission mounting. Replaces #4089635 for smaller type wiper gear, about 7/8" X 1-1/8". Early series models only.
1-3/8" Parking Brake Grommet
p/n: 50-0555-20
This Parking Brake Grommet is used to run the parking brake cable through the frame. Designed from original part for excellent workmanship.
Hood Bumper
p/n: 34-0311-42
Bumper, hood, fastened to cowl at rear of hood. Steel core. One and eleven sixteenths (1-11/16) inch diameter. Two (2) per car.
Shock or Stabilizer Link Cross Pin Bushing
p/n: 50-0220-32
This Shock or Stabilizer Link Cross Pin Bushing is designed from the original part for superior fitment and function. A rubber bushing for shock absorber link cross pin or stabilizer cross link pin.
Transmission Mount
p/n: 70-2058-25
This Transmission Mount is a new aftermarket replacement mount manufactured to meet or exceed factory specifications.. One (1) required per vehicle.
Vent Window Division Post Weatherstrip
p/n: 70-0040-56
This Vent Window Division Post Weatherstrip is an extruded thirty (30") inch rubber strip that may have to be glued to your old original division post seal core, or directly to the division post.
Tailgate bumper
p/n: 70-2854-87
Bumper, tailgate support. Two (2) bumpers mount on tailgate and two (2) mount on body in lower sections. Four (4) required.
Clutch and Brake Pedal Bump Stops
p/n: 70-4805-24
This Clutch and Brake Pedal Bump Stop pair is designed from the original part for superior fitment, finish and function. These rubber bumpers help align your brake and clutch pedals in the correct position, while also preventing rattles and squeaks.
Convertible Top Arm Cover Cap
p/n: 70-0736-67
This four (4) piece Convertible Top Arm Cover Cap set is designed from the original part for superior fitment, finish and function. Installs on the folding pillar to side roof rail links. A perfect copy in original grey rubber. Four (4) piece set.Length: 1-3/4" inches.
Steering Column Gasket - Automatic Transmission
p/n: 70-4467-36
This Steering Column gasket is designed from the original part for superior fitment and sealing. Gasket is machine cut from quality sponge rubber to authentic original dimensions. This part fits around the steering column to seal the column through the body floor pan.
Dimmer Switch Grommet
p/n: 40-0083-88
This Dimmer Switch Grommet is used during carpet installations in automotive restorations. Made from high-quality EPDM dense rubber to provide excellent durability. Includes a wide flange for floor dimmer switch fitments.
Body Mount Isolator Pad
p/n: 50-0507-48
Isolator, body mounting. Fully molded rubber. Two inches (2") outside diameter by seven eighths inch (7/8") inside hole diameter by three fourths inch (3/4") height.
Body Mounting Pad
p/n: 50-0361-48
Pad, body mounting. Required replacement for body-off restorations. Constructed of high quality rubber for long lasting durability. Two inch (2") square by fifteen sixteenths inch (15/16) inside hole diameter by one fourth inch (1/4") height.
Strut Rod Bushing
p/n: 50-0522-27
Bushing, strut rod at drive shaft tube. Two (2) per car required.Length: 1.65625 inches.
Tailgate wedge
p/n: 70-2855-87
Wedge, tailgate bumper anti-rattler. Mounts on both end jamb areas on tailgate.
1-5/8" Firewall Grommet
p/n: 50-0364-20
This Firewall Grommet is used to run the oil pressure and water temperature, or washer vacuum hose through the firewall. Designed from original part for excellent workmanship.
1-5/8" Firewall Grommet
p/n: 50-0363-20
This Firewall Grommet is used to run the windshield washer hose through the firewall. Designed from original part for excellent workmanship.
Adjustable Hood Bumper
p/n: 70-1084-42
This Adjustable Hood Bumper is designed from the original part for superior fitment, finish and function. Adjustable with molded on rubber cap.
Body Mounting Pad
p/n: 50-0097-48
Pad, several usages. Use as a body mounting pad or as a cushion for body mounting bolt. Fully molded rubber. Up to twenty (20) required per car.
Door Handle Gasket Set
p/n: 60-0640-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This six (6) piece gasket set will do two (2) doors.
Hood Bumper
p/n: 50-0489-42
Bumper, hood to fender ledge. Number required varies. Molded rubber type.Width: 1.5 inches. Height: 1.0 inches.
License lens gasket
p/n: 50-0357-17
Gasket set, rear license light assembly. One (1) rubber ring and one (1) cork rubber gasket comprise set.
Door Handle Gasket Set
p/n: 70-1647-69
This Door Handle Gasket Set is designed from the original part for superior fitment and seal. This four (4) piece gasket set will do two (2) doors.
Shock Absorber Bushing
p/n: 50-0087-33
Bushing, Delco type, shock absorber link. One and five sixteenths (1-5/16) inch outside diameter, seven sixteenths (7/16) inch inside diameter.
Tailgate Bumper
p/n: 70-1910-87
This Tailgate Bumper is designed from the original part for superior fitment, finish and function. This station wagon tailgate bumper is commonly used on GM station wagon models.
Body Mounting Pad
p/n: 50-0328-48
Pad, body mounting to frame. Fully molded rubber. Up to twenty (20) required per car. Check number needed for your particular body. Two inch (2") square by five eights inch (5/8") inside hole diameter by seven sixteenths inch (7/16") height.
Plastic Guide Plate
p/n: 50-0385-58
Plastic guide plate, attaches to various outer scraper weatherstrips.Length: 1.625 inches. Width: .625 inches.
Axle Rebound Pad
p/n: 50-0302-35
Bushing, rear axle, anti-sway rod ends. Fully molded rubber. Four (4) required per car.
Body Mounting Pad
p/n: 50-0132-48
Pad, body mounting. Fully molded rubber. One and three fourths inch (1 3/4") outside diameter by three eighths inch (3/8") inside hole diameter by five sixteenths inch (5/16") height.
Body Mounting Pad
p/n: 50-0131-48
Pad, body mounting. Fully molded rubber with locating collar. Two-inch (2") square by thirteen sixteenths inch (13/16") locating collar outside diameter by one half inch (1/2") locating collar inside diameter.
Body Mounting Pad
p/n: 50-0133-48
Pad, body mounting. Fully molded rubber. Two inches (2") outside diameter by three eighths inch (3/8") inside hole diameter by three eighths inch (3/8") height.
Wiper Transmission Gasket
p/n: 50-0484-53
Gasket, windshield wiper transmission to cowl. Steel rule die cut replacement for #4587667.
Door Bumper
p/n: 70-1156-71
Door Side Bumper made from EPDM Dense rubber. Clip retained. Appears identical to Atwood #107, #208. Width: 1-1/2" inches. Height: 1-5/16"
Door Bumper
p/n: 70-1155-71
Pad, door jamb (door side bumper).Length: 1.25 inches. Width: .9375 inches.